AD841KN - Wideband Unity-Gain Op Amp | Analog Devices
料号: AD841KN ✓ 量产中AD841KN 概述
An operational amplifier is a voltage-controlled, high-gain active device used in feedback networks to amplify, filter, buffer, or compare signals. The AD841KN is a single amplifier rather than an instrumentation amplifier, so its external resistor and compensation choices determine the usable gain, bandwidth, output drive, and offset behavior. Its unity-gain stability makes it suitable for closed-loop voltage followers and noninverting stages without relying on the minimum stable gain of the related AD840.
The principal differentiators are unity-gain stability, wide bandwidth, and the family’s junction-isolated complementary bipolar construction. Analog Devices identifies the AD841 as a member of a high-speed, high-precision amplifier family and describes the AD842 as a related device that is stable at a gain of two or greater and provides at least 100 mA of output-current drive. The AD841 is intended for systems that need its particular unity-gain-stable profile rather than the gain-of-two stability and output-drive characteristics of the AD842.
The bipolar process combines DC precision with wideband AC performance. In practical closed-loop designs, the useful bandwidth depends on amplifier gain, feedback impedance, load capacitance, slew rate, output-current demand, and power-supply bypass. Component selection should account for the complete feedback network because a nominally unity-gain-stable device still requires stable resistors, suitable output loading, and clean supply rails to preserve expected settling behavior.
Typical applications include precision signal conditioning, active filtering, waveform amplification, instrumentation interfaces, low-level sensor conditioning, and communication-signal paths. It can also serve as a buffered output stage when the circuit requires more drive than a general-purpose precision amplifier provides. In systems using the related family, the AD840 is optimized for stability at gains of ten or greater, while the AD842 supports gains of two or greater.
For layout, place input and feedback components close to the amplifier pins, minimize feedback-loop area, and decouple each supply pin near the device. Avoid excessive capacitive loading on the output because it can impair stability and settling. Confirm operation across the intended supply voltage, load, temperature, and source impedances using the manufacturer’s recommended configurations rather than assuming that a generic feedback network preserves full bandwidth.
This product page combines the AD841 family architecture, package details, replacement considerations, comparison data, and practical design guidance. It helps engineers distinguish the AD841KN’s unity-gain-stable role from the gain-specific AD840 and AD842 alternatives while preserving the same 14-pin PDIP footprint.
直接替换替代料: AD841KN ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
AD841KNZ
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
AD841ANZ
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
AD841BNZ
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
AD841JNZ
✅ 直接替换📋 参考替代料(不在目录中)
AD841KN 最大额定值与电气特性
| Product Type | Single wideband operational amplifier |
| Amplifier Architecture | Voltage-feedback operational amplifier |
| Gain Stability | Unity-gain stable |
| Process Technology | Junction-isolated complementary bipolar (CB) process |
| Number of Circuits | 1 circuit |
| 封装 | 14-pin PDIP |
| 安装类型 | Through-hole |
| Related Family Output Drive | 100 mA minimum for AD842 |
| Related AD840 Stability | Gain of 10 or greater |
| Related AD842 Stability | Gain of 2 or greater |
AD841KN 引脚配置
| 引脚 1 | NC — Not connected (per datasheet) |
| 引脚 2 | -IN — Inverting input |
| 引脚 3 | +IN — Non-inverting input |
| 引脚 4 | V- — Negative power supply |
| 引脚 5 | NC — Not connected (per datasheet) |
| 引脚 6 | OUT — Output |
| 引脚 7 | V+ — Positive power supply |
| 引脚 8 | NC — Not connected (per datasheet) |
| 引脚 9 | NC — Not connected (per datasheet) |
| 引脚 10 | NC — Not connected (per datasheet) |
| 引脚 11 | NC — Not connected (per datasheet) |
| 引脚 12 | NC — Not connected (per datasheet) |
| 引脚 13 | NC — Not connected (per datasheet) |
| 引脚 14 | NC — Not connected (per datasheet) |
典型应用
AD841KN 适用于 6 应用s: Precision Voltage Buffer, Active Analog Filtering, Low-Level Sensor Signal Conditioning, Instrumentation Input Interface, Waveform Amplification, Communication Signal Conditioning.
Precision Voltage Buffer
The AD841KN is well suited to a unity-gain voltage buffer because the AD841 is explicitly unity-gain stable. Placing the amplifier directly in the feedback path can provide a low-impedance output for a high-impedance source without adding another gain stage. This application benefits from the device’s junction-isolated complementary bipolar construction, which Analog Devices describes as combining DC precision with wideband AC performance. The designer should still minimize feedback-loop area, provide local supply bypassing, and confirm output settling against the intended load. Unity-gain stability removes the minimum-gain constraint associated with the related AD840, while the AD842 is intended for operation at gains of two or greater and includes 100 mA minimum output-current drive.
推荐
Active Analog Filtering
The AD841KN can form the gain element in an active filter when the selected closed-loop gain is compatible with unity-gain stability. Its wideband bipolar implementation supports signal-chain applications where filtering must preserve phase and amplitude accuracy over a useful frequency range. Component values and source impedances remain important because parasitic capacitance, resistor tolerance, and amplifier drive can alter the intended response. Use the manufacturer application guidance to select stable feedback ratios and verify the completed filter with realistic loading. Compared with the AD840, the AD841 permits lower closed-loop gains; compared with the AD842, it targets unity-gain operation rather than the AD842’s gain-of-two-or-higher regime.
推荐
Low-Level Sensor Signal Conditioning
The AD841KN is applicable to low-level sensor conditioning when the circuit requires a precision bipolar amplifier with wideband response. The AD841 family’s junction-isolated CB process supports operation where both DC accuracy and AC bandwidth matter, such as conditioning outputs from pressure, temperature, or current-sensing elements. Designers should account for input bias current, source impedance, offset behavior, and common-mode range using the exact manufacturer electrical tables. Local grounding and short input paths are essential to prevent sensor traces from adding pickup or phase shift. The AD841’s unity-gain stability is useful for first-stage buffers, whereas the related AD842 becomes attractive when gain of two or greater and stronger output-current drive are required.
推荐
Instrumentation Input Interface
The AD841KN can serve as an interface element in an instrumentation signal chain when the instrumentation architecture includes discrete precision amplification stages. Its wideband, unity-gain-stable behavior allows it to buffer sensor inputs or support low-gain amplification before a subsequent measurement stage. Practical implementation requires careful attention to bias-current return paths, resistor matching, common-mode limits, and power-supply rejection for the selected operating frequency. A unity-gain follower also makes the AD841 useful when preserving sensor voltage while presenting a lower output impedance to an ADC driver. For designs built around gain of two or greater, the AD842 provides a distinct alternative with 100 mA minimum output-current drive, while the AD840 targets higher-gain architectures.
推荐
Waveform Amplification
The AD841KN can amplify waveforms in test, communications, and signal-analysis circuits where unity-gain stability and wideband behavior are useful. The bipolar process supports a combination of DC precision and AC performance, helping the amplifier process signals with both static and dynamic content. Feedback resistance and capacitance must be selected to preserve the intended closed-loop response, while output loading should be checked for adequate current drive and settling. The AD841 is especially suitable for voltage-following and low-gain waveform stages. The AD842 is a different choice for gain-of-two-or-higher signal paths that benefit from its 100 mA minimum output-current capability, and the AD840 is intended for stable operation at gains of ten or greater.
推荐
Communication Signal Conditioning
The AD841KN is suitable for communication-signal conditioning when a compact precision bipolar stage is needed ahead of a converter, receiver, or measurement block. Wideband operation can preserve fast signal transitions, while unity-gain stability supports direct buffering without requiring a minimum gain of two or ten. Board implementation should use short, impedance-controlled paths, clean return planes, and close decoupling to prevent supply noise or trace pickup from degrading the amplified waveform. The operating point must remain within the exact supply, input common-mode, output-swing, and output-current limits defined for the AD841. For higher-gain stages requiring greater drive, the AD842 offers 100 mA minimum output-current capability, whereas the AD840 is optimized for gains of ten or greater.
推荐
推荐产品汇总
工程参考数据: AD841KN ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | AD841KNZ | AD841ANZ | AD841BNZ | AD841JNZ |
|---|---|---|---|---|---|
| Package | 14-pin PDIP | 14-pin PDIP - same | 14-pin PDIP - same | 14-pin PDIP - same | 14-pin PDIP - same |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Core Function | Wideband unity-gain-stable operational amplifier | Wideband unity-gain-stable operational amplifier | Wideband unity-gain-stable operational amplifier | Wideband unity-gain-stable operational amplifier | Wideband unity-gain-stable operational amplifier |
| Number of Circuits | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Minimum Stable Gain | Unity gain | Unity gain | Unity gain | Unity gain | Unity gain |
| Process Technology | Junction-isolated complementary bipolar process | Junction-isolated complementary bipolar process | Junction-isolated complementary bipolar process | Junction-isolated complementary bipolar process | Junction-isolated complementary bipolar process |
| Related AD842 Minimum Stable Gain | AD842 stable at gain of 2 or greater | AD842 stable at gain of 2 or greater | AD842 stable at gain of 2 or greater | AD842 stable at gain of 2 or greater | AD842 stable at gain of 2 or greater |
| Related AD840 Minimum Stable Gain | AD840 stable at gain of 10 or greater | AD840 stable at gain of 10 or greater | AD840 stable at gain of 10 or greater | AD840 stable at gain of 10 or greater | AD840 stable at gain of 10 or greater |
关键差异点
- Unity-gain operation (对比 AD842)
- Broader usable gain range than AD840 (对比 AD840)
- Same-package family migration (对比 AD841JNZ)
设计说明
Keep the AD841KN input and feedback network close to the package and minimize the loop enclosed by the feedback components. Place the supply-bypass capacitors immediately across the positive and negative supply pins, with short ground returns. For a high-speed design, inspect the assembled board with an oscilloscope because probe grounding and long input traces can create behavior that is not represented by a simple ideal-op-amp model.
Do not select the AD841 on package similarity alone. The AD841 is unity-gain stable, while the related AD842 is stable at gains of two or greater and the related AD840 is stable at gains of ten or greater. A circuit designed around a different minimum stable gain can show ringing or unstable settling even when all three devices use a comparable footprint. Confirm the exact AD841 feedback configuration against the manufacturer guidance.
Evaluate output loading and settling rather than relying only on nominal bandwidth. Include the source impedance, feedback impedance, load capacitance, supply range, and intended closed-loop gain in the stability assessment. Extra output capacitance can disrupt transient behavior, so avoid adding long cable or capacitive loads directly to the output without checking the manufacturer’s recommended drive and compensation arrangements.
合规信息
Compliance attributes are not stated in the manufacturer product-page or datasheet excerpts associated with this listing. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status for the exact orderable suffix before production release.