AD842SH - 80MHz Wide-Bandwidth Operational Amplifier | Analog Devices
MPN: AD842SH ✓ सक्रियAD842SH अवलोकन
An operational amplifier is an analog signal-processing IC that amplifies the voltage difference between its inverting and non-inverting inputs while offering high open-loop gain and low output impedance. The AD842 belongs to the operational-amplifier hierarchy within amplifier ICs and power-management systems used for instrumentation, industrial control, communications, and high-speed analog signal acquisition.
The AD842SH combines wide bandwidth with precision DC characteristics. Key ratings include 115 dB open-loop gain, 9 nV/√Hz input noise at 1 kHz, 1.5 mV maximum input offset voltage, and 14 µV/°C input offset drift. Its 375 V/µs slew rate supports accurate reproduction of high-frequency, large-amplitude signals, while the 8 µA input bias current is suitable for many high-impedance source designs.
The amplifier is fabricated using Analog Devices' junction-isolated complementary bipolar process. This process combines DC precision with wideband AC performance. The 80 MHz gain-bandwidth product supports closed-loop bandwidth near 10 MHz when configured for a gain of 8, making the device useful where conventional precision op amps cannot preserve signal amplitude at higher frequencies.
Typical uses include low-level instrumentation-amplifier front ends, precision signal conditioners, active filters, broadband measurement systems, and industrial analog interfaces. In a typical non-inverting or inverting amplifier, external resistors establish the closed-loop gain while the compensation capacitor selected for that gain controls frequency response and stability.
Design the AD842SH around its supply limits, input common-mode range, output swing, noise bandwidth, and required gain. Keep sensitive input and feedback nodes short, use stable reference and gain resistors, and place compensation components close to the relevant pins. Verify thermal rise and output drive at the lowest expected supply voltage because both can limit large-signal performance.
This page combines manufacturer specifications, package information, sourcing guidance, replacement considerations, and practical circuit-design notes. It helps engineers evaluate whether the AD842SH's 80 MHz bandwidth, 375 V/µs slew rate, 115 dB gain, and hermetic 12-lead TO-8 package satisfy a precision analog design before committing the component to a PCB or production BOM.
के लिए ड्रॉप-इन विकल्प AD842SH — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
AD842JH
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
AD842SHZ
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
AD842SH/883
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
AD842SQ
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →AD842SH Maximum Ratings और Electrical Characteristics
| Product Type | Single-channel operational amplifier |
| Gain-Bandwidth Product | 80 MHz |
| Slew Rate | 375 V/µs |
| Open-Loop Gain | 115 dB |
| Input Offset Voltage | 1.5 mV maximum |
| Input Offset Drift | 14 µV/°C maximum |
| Input Noise Density | 9 nV/√Hz at 1 kHz |
| Input Bias Current | 8 µA |
| Maximum Supply Voltage | 18 V |
| ऑपरेटिंग तापमान रेंज | 0°C to +70°C |
| पैकेज | TO-8 style, 12 leads |
| माउंटिंग प्रकार | Through-hole |
| Process Technology | Junction-isolated complementary bipolar process |
| Number of Channels | 1 channel |
| RoHS स्थिति | Compliant |
AD842SH to-8 style, 12 leads पिन कॉन्फ़िगरेशन गाइड
AD842SH (to-8 style, 12 leads पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस एनालॉग कंपोनेंट में इनपुट, आउटपुट और पावर सप्लाई पिन हैं। ऑफ़सेट नल, कम्पनसेशन और एनेबल पिन कॉन्फ़िगरेशन के लिए निर्माता डेटाशीट देखें। सिग्नल कंडीशनिंग और एम्प्लीफ़ायर सर्किट के लिए आदर्श।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: AD842SH.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
AD842SH के लिए उपयुक्त है 6 अनुप्रयोगs: Precision Instrumentation Front End, Active Analog Filters, Industrial Signal Conditioning, Broadband Measurement Systems, Communications Signal Interface, Precision Data Acquisition.
Precision Instrumentation Front End
The AD842SH fits low-level instrumentation front ends where sensor signals require accurate DC behavior without sacrificing bandwidth. Its 115 dB open-loop gain, 1.5 mV maximum input offset voltage, and 14 µV/°C offset drift help preserve small measurement signals through the amplifier stage. The 80 MHz gain-bandwidth product also supports transient content that would be attenuated by a slower precision amplifier. Configure the gain with low-noise resistors, select the compensation capacitor for the intended closed-loop gain, and verify the input common-mode range against the sensor output. The device's 375 V/µs slew rate provides additional margin when the amplified waveform contains sharp, low-amplitude transitions.
अनुशंसित
Active Analog Filters
The AD842SH is appropriate for active filtering stages that must retain small signals while processing higher-frequency components. Its 80 MHz gain-bandwidth product provides substantial loop bandwidth for moderate closed-loop gains, and the 375 V/µs slew rate helps limit large-signal distortion. Component tolerances in the feedback network determine the actual filter response, while the op amp's 9 nV/√Hz input noise at 1 kHz contributes to the output noise spectrum. Choose the gain and compensation network together, keep the summing node physically compact, and test stability with the intended source impedance. The hermetic TO-8-style, 12-lead package supports laboratory, industrial, and legacy instrument installations where through-hole construction is preferred.
अनुशंसित
Industrial Signal Conditioning
The AD842SH can condition low-level industrial process signals while providing the bandwidth needed for sensor and control-loop dynamics. Its 1.5 mV maximum input offset and 14 µV/°C drift limit static error, while its 80 MHz gain-bandwidth product avoids unnecessarily limiting dynamic response. Place the amplifier close to the sensor or connector when source impedance and cable noise are significant, and keep the return path continuous to reduce common-mode pickup. The 18 V maximum supply rating permits conventional bipolar rails, but the output must remain inside the load-dependent swing range. For factory equipment, qualify the exact operating-temperature grade and verify thermal performance across the expected ambient range before production release.
अनुशंसित
Broadband Measurement Systems
The AD842SH is suitable for broadband measurement systems that combine high open-loop gain with rapid signal settling. The 80 MHz gain-bandwidth product allows useful closed-loop bandwidth at moderate gain, while the 375 V/µs slew rate helps preserve amplitude and phase behavior for fast waveforms. Its 9 nV/√Hz input noise at 1 kHz is important when the measured quantity is close to the noise floor. Use short feedback components, maintain symmetric routing where practical, and ensure the source and load impedances do not interfere with the selected compensation network. For oscilloscope-style analog channels, verify output swing, slew-limited bandwidth, and thermal rise at the maximum expected input amplitude.
अनुशंसित
Communications Signal Interface
The AD842SH can serve as an analog interface in communication equipment where received signals require linear amplification across a broad frequency range. Its 115 dB open-loop gain provides strong loop gain, while the 80 MHz gain-bandwidth product and 375 V/µs slew rate support higher-rate analog waveforms. The input noise density of 9 nV/√Hz at 1 kHz can matter in low-amplitude receiver channels. Maintain controlled impedance on the input path, use short ground returns, and decouple the supply pins close to the device. Designers should check the exact common-mode range, output swing, and stability requirements for the selected gain. The hermetic 12-lead package is particularly suitable for legacy communication and test equipment built with through-hole components.
अनुशंसित
Precision Data Acquisition
The AD842SH is useful in precision data-acquisition chains that amplify sensor outputs ahead of an ADC or measurement converter. Low input offset and drift reduce static gain error, while the 80 MHz gain-bandwidth product allows the amplifier to preserve fast events without adding a bandwidth bottleneck. At 9 nV/√Hz input noise density at 1 kHz, source resistance and resistor selection can materially influence total noise, so use low-value thermal-noise resistors where appropriate. Keep the input connection short and place the input and feedback resistors close to the device. Confirm that the signal remains within the input common-mode range and that the output swing accommodates the converter reference and full-scale requirements.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा AD842SH — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | AD842JH | AD842SHZ | AD842SH/883 | AD842SQ |
|---|---|---|---|---|---|
| Package | TO-8 style, 12 leads | TO-8 style, 12 leads | TO-8 style, 12 leads | TO-8 style, 12 leads | TO-8 style, 12 leads |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Product Family | AD842 | AD842 | AD842 | AD842 | AD842 |
| Special Ordering Feature | SH ordering code | JH ordering code | Z ordering suffix | 883 screening designation | SQ ordering code |
मुख्य विशेषताएँ
- Wide-bandwidth precision in a hermetic package (बनामAD842JH)
- Low-noise operation supports small-signal measurement (बनामAD842SQ)
- Fast large-signal response (बनामAD842SH/883)
डिज़ाइन नोट्स
Route the input, feedback, compensation, and ground paths as short as practical. The AD842SH's 80 MHz gain-bandwidth product makes parasitic capacitance and long feedback loops significant, especially at higher closed-loop gains. Place input and feedback resistors close to their associated pins, keep the compensation capacitor adjacent to the compensation pin, and provide a low-impedance ground return. Review the completed layout against the manufacturer's typical application circuit and evaluate stability across the intended source impedance.
Use separate, physically close bypass paths for the positive and negative supply pins to limit inductive impedance at high frequency. The device supports an 18 V maximum total supply voltage, but the usable input and output range also depends on the chosen rails. Confirm common-mode range, output swing, and stable operation at the minimum supply voltage before release. Decoupling capacitance and voltage ratings should be selected for the actual rail arrangement and transient environment.
Do not treat every AD842 ordering suffix as electrically and administratively interchangeable. The AD842JH, AD842SHZ, AD842SH/883, and AD842SQ may differ in qualification, screening, or ordering treatment even though they use the same TO-8-style 12-lead package family. Before substitution, compare the ordering guide, temperature range, offset-voltage limits, screening requirements, and pin assignments. Never adapt an 8-pin TO-8 or SOIC footprint to this 12-lead device.
अनुपालन जानकारी
The component listing identifies the AD842SH as RoHS compliant. The hermetic TO-8-style package and 0°C to +70°C specification are not automotive qualifications; no AEC-Q100 status applies.