ADF4112BCPZ-RL7 - 3 GHz Integer-N PLL | Analog Devices
MPN: ADF4112BCPZ-RL7 ✓ सक्रियADF4112BCPZ-RL7 अवलोकन
A frequency synthesizer is a clock-and-timing IC that locks an output oscillator to a stable reference frequency. In the ADF4110 family hierarchy, the phase-frequency detector compares the divided reference with the divided feedback signal, while the charge pump converts phase and frequency error into a control voltage for an external voltage-controlled oscillator. This PLL is therefore an integer-N RF synthesizer rather than a fixed-frequency clock generator or a direct RF mixer.
Key features include a maximum frequency of 3 GHz, RF bandwidth to 4 GHz, a 2.7 V to 5.5 V supply range, and selectable 4/5 and 8/9 prescaler ratios. The 6-bit A counter and 13-bit B counter establish the programmable integer-N division ratio. Programmable charge-pump currents support adjustment of loop current, while the reference divider permits division of the external reference signal.
The ADF4110 family architecture uses a low-noise digital phase-frequency detector, a precision charge pump, a programmable reference divider, programmable A and B counters, and a dual-modulus P/P+1 prescaler. The synthesizer produces a tuning voltage through the charge-pump output, so an external loop filter, tank circuit, and VCO are normally required. The separate supply or voltage arrangement should follow the pin-description and application-circuit tables in the manufacturer datasheet.
Typical applications include wireless receiver and transmitter local oscillators, RF up-conversion and down-conversion stages, wireless communication equipment, and test equipment requiring programmable RF synthesis. The 3 GHz ceiling is appropriate for many conventional RF bands, while the 4 GHz RF bandwidth supports higher operating conditions described by Analog Devices. Designers must still verify the VCO range, divider path, reference ratio, and lock-range requirements for the intended channel plan.
The critical design consideration is loop behavior. Prescaler choice, charge-pump current, reference-divider ratio, filter resistance and capacitance, and VCO tuning range determine lock time, phase noise, reference spurs, and maximum achievable output frequency. Use the manufacturer application information to select the prescaler, filter components, and external VCO before treating the ADF4112BCPZ-RL7 as a complete frequency-generation solution.
This product page combines the ADF4112 technical specifications, package and ordering information, pin-compatible family candidates, comparison parameters, and practical RF layout guidance into one engineering reference. It also highlights where external RF and passive components are required, helping designers distinguish the synthesizer IC from a standalone oscillator or complete RF signal chain.
के लिए ड्रॉप-इन विकल्प ADF4112BCPZ-RL7 — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस सीरीज़ के वेरिएंट
समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं ADF4112BCPZ-RL7 (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Package, Product Type.
ADF4113BCPZ
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →ADF4114BCPZ
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित📋 संदर्भ विकल्प (कैटलॉग में नहीं)
ADF4117BCPZ
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित📋 संदर्भ विकल्प (कैटलॉग में नहीं)
ADF4112BCPZ-RL7 विशेषताएं
| Device Type | Single, integer-N RF PLL frequency synthesizer |
| Maximum Synthesizer Frequency | 3 GHz |
| RF Bandwidth | 4 GHz |
| Number of Synthesizers | 1 |
| Supply Voltage Range | 2.7 V to 5.5 V |
| ऑपरेटिंग तापमान रेंज | -40 °C to +85 °C |
| Prescaler Ratios | 4/5 or 8/9 |
| A Counter Width | 6 bit |
| B Counter Width | 13 bit |
| Reference Divider | Programmable |
| Charge-Pump Current | Programmable |
| Phase-Frequency Detector | Low-noise digital PFD |
| पैकेज | 20-WFQFN exposed-pad CSP |
| माउंटिंग प्रकार | Surface mount |
| Manufacturer Lifecycle Status | Production |
ADF4112BCPZ-RL7 20-wfqfn exposed-pad csp पिन कॉन्फ़िगरेशन गाइड
ADF4112BCPZ-RL7 (20-wfqfn exposed-pad csp पैकेज) के लिए पिन कॉन्फ़िगरेशन। पिन नंबरिंग, फ़ंक्शन और कनेक्शन आरेख निर्माता डेटाशीट में परिभाषित हैं। सटीक फुटप्रिंट और सोल्डरिंग दिशानिर्देशों के लिए इसे देखें।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: ADF4112BCPZ-RL7.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
ADF4112BCPZ-RL7 के लिए उपयुक्त है 6 अनुप्रयोगs: Wireless Receiver Local Oscillator, Wireless Transmitter Up-Conversion, RF Down-Conversion, Programmable RF Test Equipment, Industrial RF Monitoring, RF Communication Module.
Wireless Receiver Local Oscillator
The ADF4112BCPZ-RL7 is appropriate for a programmable wireless receiver local oscillator when the required channel is within its 3 GHz maximum synthesis frequency. The 4/5 or 8/9 prescaler, 6-bit A counter, and 13-bit B counter establish the integer-N division ratio, while the reference divider adapts the incoming reference to the channel plan. A suitable external VCO and passive loop filter remain necessary. The design should be checked for lock range across temperature, reference spur suppression, phase noise, and the required settling time after a channel change.
Wireless Transmitter Up-Conversion
In a wireless transmitter up-conversion chain, the ADF4112BCPZ-RL7 can generate the programmable local-oscillator signal used by an RF mixer. Its 3 GHz maximum synthesis frequency covers many conventional RF operating bands, while the selectable prescaler supports flexible integer-N ratios. Engineers must choose the external VCO tuning range to cover the complete channel plan and calculate the loop filter around the selected charge-pump setting. The resulting design should then be evaluated for phase noise, unwanted reference spurs, output-power stability, and lock behavior during rapid frequency changes.
RF Down-Conversion
The ADF4112BCPZ-RL7 can supply the local-oscillator signal used in an RF down-conversion stage for wireless equipment. Programmable reference division and integer-N counters allow channel frequencies to be derived from one reference source, reducing the need for multiple oscillators. Because the device is a synthesizer rather than a complete VCO, the external VCO must overlap the required local-oscillator range. Validate mixer drive requirements, harmonic content, phase-noise contribution, spur levels, and synthesizer settling time as a combined signal-chain budget.
Programmable RF Test Equipment
The ADF4112BCPZ-RL7 is useful in programmable RF test equipment requiring a local oscillator below 3 GHz. Its integer-N architecture allows one reference source to produce multiple programmable frequencies, simplifying RF channel simulation and receiver-stimulus systems. The engineer should select a reference frequency and divider ratio that supports every required test channel while maintaining integer division. External loop-filter and VCO design quality will determine settling time and spectral purity, so the final instrument specification should be verified against phase-noise, spurious-signal, and amplitude-accuracy requirements.
Industrial RF Monitoring
For industrial RF monitoring equipment, the ADF4112BCPZ-RL7 can generate a programmable oscillator for sensing or communication front ends operating within the 3 GHz limit. Its surface-mount 20-WFQFN exposed-pad package supports compact instrument designs, while the integer-N architecture provides repeatable channel selection from a stable reference. Industrial enclosure temperature changes may shift the external VCO and loop characteristics, so the design should include sufficient tuning margin. Validate conducted and radiated emissions as well as lock performance across the full industrial temperature range.
RF Communication Module
The ADF4112BCPZ-RL7 can implement a compact programmable RF communication local oscillator when the carrier frequency and internal reference arrangement meet its synthesizer limits. Its 2.7 V to 5.5 V supply range permits integration with low-voltage RF circuitry, while the programmable prescaler and counters support multiple frequency plans. The external VCO and loop filter should be placed to minimize RF coupling and reference noise. Confirm conducted emissions, output-buffer isolation, temperature drift, and frequency accuracy before using the oscillator in a compact communications module.
के लिए इंजीनियरिंग संदर्भ डेटा ADF4112BCPZ-RL7 — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | ADF4113BCPZ | ADF4114BCPZ | ADF4117BCPZ |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 20-WFQFN Exposed Pad, CSP | 20-WFQFN Exposed Pad, CSP | 20-WFQFN Exposed Pad, CSP | 20-WFQFN Exposed Pad, CSP |
| Device Type | Single, integer-N RF PLL frequency synthesizer | Integer-N RF PLL frequency synthesizer | Integer-N RF PLL frequency synthesizer | Integer-N RF PLL frequency synthesizer |
मुख्य विशेषताएँ
- Higher operating-frequency capability (बनामADF4113BCPZ)
- 3 GHz synthesis ceiling with 4 GHz RF bandwidth (बनामADF4117BCPZ)
- Single-family programming environment (बनामADF4114BCPZ)
डिज़ाइन नोट्स
Use the manufacturer application layout as the foundation for the reference input, charge-pump output, feedback input, supply decoupling, and exposed-pad connection. Keep the sensitive phase-detector and feedback paths away from the VCO control line and minimize loop-filter area. A compact ground return around the exposed pad improves thermal performance, but the pad connection and pin mapping must follow the official ADF4112 package drawing.
Do not select the ADF4112BCPZ-RL7 solely from its 3 GHz maximum rating. Confirm that the external VCO covers every required channel, that the selected 4/5 or 8/9 prescaler provides adequate division range, and that the reference-divider and A/B counters generate the intended integer-N ratio. Check lock range across temperature and supply tolerance before committing the PCB.
Reference-divider pulses and charge-pump current can create harmonics that interfere with sensitive RF stages. Place the loop filter close to the charge-pump output and VCO tuning input, use a properly terminated reference source, and route high-speed feedback away from sensitive analog nodes. Evaluate conducted and radiated emissions with the final enclosure and external VCO because PCB-level behavior can differ substantially from schematic-level expectations.
Use the exposed pad and PCB copper area as the primary thermal path, following the manufacturer's land-pattern guidance. Keep the analog ground connection consistent with the datasheet recommendation and avoid placing a thermal break beneath the pad. Thermal performance depends on copper area, board layers, airflow, and neighboring heat sources, so calculate the junction-temperature rise for the maximum ambient and supply condition.
अनुपालन जानकारी
The manufacturer product page identifies the ADF4112 as a production device but does not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status on the cited page.