Microchip Technology

AT90CAN128-15MT - 128KB CAN AVR MCU | Microchip Technology

MPN: AT90CAN128-15MT ✓ सक्रिय
2.7 V to 5.5 V Vdss 64-QFN (9 x 9 mm), exposed pad Package 15 MHz Speed 128 KB Memory
न्यूनतम ऑर्डर मात्रा: 1 |

AT90CAN128-15MT अवलोकन

Microchip Technology AT90CAN128-15MT is an 8-bit AVR RISC microcontroller with 128 KB of ISP flash memory, 4 KB EEPROM, 4 KB SRAM, 53 general-purpose I/O lines, and 32 general-purpose working registers. The device integrates a CAN 2.0A/V2.0B-compatible controller and is offered in a 64-QFN exposed-pad package. The -15 speed grade operates at up to 15 MHz.

An 8-bit microcontroller is a programmable semiconductor that integrates a processor core, nonvolatile program memory, data memory, and peripheral interfaces onto one device. The AT90CAN128 belongs to the AVR family of low-power CMOS embedded controllers. Its enhanced RISC architecture, communication peripherals, and mixed-signal capability make it suitable for embedded control systems where CAN networking, deterministic control, and compact board area are important.

The AT90CAN128-15MT provides 128 KB of flash for application firmware, 4 KB of EEPROM for nonvolatile parameter storage, and 4 KB of SRAM for working data. Its 53 I/O lines support digital interfaces, while 32 working registers support efficient AVR instruction execution. The integrated CAN controller communicates using CAN 2.0A/V2.0B-compatible protocols, and the device also includes a real-time counter and flexible timer/counter resources.

Two USARTs provide serial communication paths, while the byte-oriented Two-Wire Interface supports a compact peripheral bus. The AT90CAN128 family also includes analog and timing resources suited to industrial monitoring, actuator control, and communication gateways. The 15 MHz grade trades some clock speed for potentially simpler timing, power-budget, and clock-tree implementation compared with the 16 MHz grade of the same family.

Typical uses include CAN-connected industrial controllers, vehicle subsystem controllers, building automation nodes, sensor aggregation equipment, and embedded CAN gateways. The 128 KB code space is useful for protocol stacks, diagnostic routines, local control logic, and application firmware. The combination of 53 I/O lines and CAN connectivity allows one device to bridge a local control network to a broader CAN bus.

PCB implementation should account for the exposed thermal pad beneath the 64-QFN package. Use the manufacturer land pattern, provide a continuous ground-plane connection to the exposed pad, and route high-current and sensitive signals away from the pad connection. Confirm external CAN transceiver, termination, clock, decoupling, and programming requirements against the manufacturer datasheet before release.

This product page combines the AT90CAN128-15MT specifications, package details, practical application guidance, and same-footprint replacement considerations into an engineering-focused reference. It also highlights where clock-grade differences matter when evaluating an alternative.

के लिए ड्रॉप-इन विकल्प AT90CAN128-15MT — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

इस सीरीज़ के वेरिएंट

समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं AT90CAN128-15MT (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Package, CAN Controller, Flash Memory, Supply Voltage Range, ADC Channels.

Microchip Technology
Package: 64-pin TQFP, 14 mm x 14 mm
CAN Controller: CAN 2.0A and CAN 2.0B compliant
Flash Memory: 128 KB (128K x 8)
इसके साथ तुलना करें AT90CAN128-15MT →
Microchip Technology
Package: 64-pin QFN (9 mm x 9 mm)
CAN Controller: CAN 2.0A / 2.0B compliant
इसके साथ तुलना करें AT90CAN128-15MT →
Microchip Technology
Package: 64-VFQFN Exposed Pad (9x9 mm)
Flash Memory: 128 KB (64K x 16)
Supply Voltage Range: 4.5 V to 5.5 V
इसके साथ तुलना करें AT90CAN128-15MT →

AT90CAN128-15MU

✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित
📦 64-QFN (9 x 9 mm), exposed pad
Same 15 MHz AT90CAN128 architecture and 64-QFN footprint; ordering-temperature and grade details require confirmation.

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

AT90CAN128-15MT1

✅ ड्रॉप-इन
📦 64-QFN (9 x 9 mm), exposed pad
Same 15 MHz AT90CAN128 architecture and 64-QFN footprint; MT1 ordering-code details require manufacturer confirmation.

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

AT90CAN128-16MU

✅ ड्रॉप-इन
Microchip Technology
📦 64-QFN (9 x 9 mm), exposed pad
AVR 8-bit RISC · 128 KB (128K x 8) · 4 KB · 4 KB · 16 MHz · 4.5 V to 5.5 V · 53 · 32

कीमत के लिए संपर्क करें

डेटाशीट देखें →

AT90CAN128-16AU

✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित
Microchip Technology
📦 64-QFN (9 x 9 mm), exposed pad
8-bit AVR RISC microcontroller with CAN controller · 16 MHz · 128 KB (128K x 8) · 4 KB · 4 KB · 53 lines · 32 registers · CAN 2.0A and CAN 2.0B compliant

कीमत के लिए संपर्क करें

डेटाशीट देखें →

AT90CAN128-16MU

✅ ड्रॉप-इन
Microchip Technology
📦 64-QFN (9 x 9 mm), exposed pad
AVR 8-bit RISC · 128 KB (128K x 8) · 4 KB · 4 KB · 16 MHz · 4.5 V to 5.5 V · 53 · 32

कीमत के लिए संपर्क करें

डेटाशीट देखें →

AT90CAN128-15MT Maximum Ratings और Electrical Characteristics

Product Type 8-bit AVR RISC microcontroller
अधिकतम क्लॉक फ़्रीक्वेंसी 15 MHz
Flash Memory 128 KB
EEPROM 4 KB
SRAM 4 KB
General-Purpose I/O Lines 53
General-Purpose Working Registers 32
CAN Controller CAN 2.0A/V2.0B compatible
USART Count 2
Two-Wire Interface Byte-oriented
Real-Time Counter 1
Supply Voltage Range 2.7 V to 5.5 V
पैकेज 64-QFN (9 x 9 mm), exposed pad
माउंटिंग प्रकार Surface mount
Core Architecture AVR enhanced RISC
Qualification AEC-Q100
RoHS स्थिति Compliant
Timer/Counters 4 flexible timer/counters

AT90CAN128-15MT 64-qfn (9 x 9 mm), exposed pad पिन कॉन्फ़िगरेशन गाइड

AT90CAN128-15MT (64-qfn (9 x 9 mm), exposed pad पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस डिजिटल IC में GPIO, संचार इंटरफ़ेस (UART, SPI, I2C) और पावर पिन शामिल हैं। वैकल्पिक पिन फ़ंक्शन और कॉन्फ़िगरेशन विकल्पों के लिए निर्माता डेटाशीट देखें। एम्बेडेड सिस्टम डिज़ाइन और PCB लेआउट के लिए आवश्यक।

AT90CAN128-15MT के लिए 64-qfn (9 x 9 mm), exposed pad पैकेज पिनआउट आरेख

इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: AT90CAN128-15MT.

देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।

सामान्य अनुप्रयोग

AT90CAN128-15MT के लिए उपयुक्त है 6 अनुप्रयोगs: CAN-Connected Industrial Controller, Vehicle Subsystem Controller, Building Automation Gateway, Sensor Aggregation Equipment, CAN Network Diagnostic Tool, Actuator and Motor-Control Node.

🏭

CAN-Connected Industrial Controller

The AT90CAN128-15MT fits industrial equipment that must exchange diagnostic or command data over a CAN bus while executing local control logic. Its 128 KB flash can hold communication handlers, diagnostics, state machines, and application firmware, while 4 KB of SRAM supports runtime buffering and 4 KB of EEPROM preserves configuration values. The 15 MHz AVR core and four timer/counters support periodic sampling and actuator timing. A separate CAN transceiver, correct 120-ohm bus termination, and carefully routed differential traces remain required for a production CAN interface.

🚗

Vehicle Subsystem Controller

The AT90CAN128-15MT is appropriate for a distributed vehicle module that receives commands over CAN and controls sensors, relays, or actuators locally. Its 53 general-purpose I/O lines provide substantial digital connectivity, and the integrated CAN 2.0A/V2.0B-compatible controller supports networked vehicle functions. Four flexible timer/counters are useful for periodic control tasks. Because automotive designs require exact qualification and temperature-range control, engineers must verify the selected order code against the Microchip automotive data sheet and system-level EMC, load-dump, and transient requirements before production use.

🧩

Building Automation Gateway

The AT90CAN128-15MT can serve as a building-automation gateway that collects sensor information and distributes control commands across a CAN-based network. Its two USARTs provide paths for local serial devices, while the byte-oriented Two-Wire Interface supports compatible peripheral sensors or actuators. The 128 KB program space is useful for protocol handling, diagnostics, logging, and application logic. Designers should isolate CAN and serial routing from sensitive inputs, provide local decoupling according to the manufacturer guidance, and verify that the 15 MHz timing budget remains adequate for the gateway protocol and update workload.

🌐

Sensor Aggregation Equipment

The AT90CAN128-15MT is well suited to industrial sensing equipment that combines multiple inputs, performs local calculations, and publishes measurements through CAN. Its 53 I/O lines can support discrete sensors and digital signaling, while 4 KB of EEPROM can retain calibration or configuration records. Four timer/counters provide periodic sampling and timing functions, and the 15 MHz grade supports deterministic control without requiring the 16 MHz clock grade. Input conditioning, analog measurement circuitry, sensor isolation, and grounding should be designed separately because the MCU provides the digital control and communication foundation rather than complete sensor front ends.

🔧

CAN Network Diagnostic Tool

The AT90CAN128-15MT can implement a compact CAN diagnostic device for bench testing, service access, or network monitoring. Its 128 KB flash can accommodate protocol firmware, fault logging, identification tables, and communication diagnostics, while the integrated CAN controller handles bus frame processing. The two USARTs can support a host computer or configuration terminal, and the 53 I/O lines allow status indicators, control inputs, and test outputs. Use an isolated transceiver arrangement where the device connects to an external vehicle or machine bus, and verify termination, common-mode protection, and EMC behavior in the final enclosure.

⚡

Actuator and Motor-Control Node

The AT90CAN128-15MT can act as a distributed actuator node that receives commands over CAN and operates local outputs using its timer and counter resources. Its 53 I/O lines allow connection to control inputs, status signals, and driver-enable circuitry, while four flexible timer/counters support pulse generation and timing functions. The 4 KB SRAM is adequate for compact command and state management, and EEPROM can preserve node identity or calibration parameters. Power-stage design, protection, thermal management, and electromagnetic compatibility remain the responsibility of the surrounding circuitry rather than the MCU itself.

अनुशंसित उत्पादों का सारांश

AT90CAN128-15MU Same-family 15 MHz CAN microcontroller variant उपयोग में: CAN-Connected Industrial Controller, Building Automation Gateway, Sensor Aggregation Equipment, CAN Network Diagnostic Tool AT90CAN128-16MU Microchip Technology उपयोग में: CAN-Connected Industrial Controller, Vehicle Subsystem Controller, Sensor Aggregation Equipment, CAN Network Diagnostic Tool, Actuator and Motor-Control Node AT90CAN128-15MT1 Same-family ordering-code alternative for review उपयोग में: Vehicle Subsystem Controller, Building Automation Gateway, Actuator and Motor-Control Node
What are the key specifications of AT90CAN128-15MT that engineers should know?
The AT90CAN128-15MT is a 15 MHz, 8-bit AVR microcontroller with 128 KB of ISP flash, 4 KB of EEPROM, 4 KB of SRAM, 53 general-purpose I/O lines, and an integrated CAN 2.0A/V2.0B-compatible controller. According to the Microchip Technology AT90CAN128 product documentation, it also includes 32 working registers, two USARTs, a byte-oriented Two-Wire Interface, a real-time counter, and four flexible timer/counters. The device is packaged in a 64-QFN package with an exposed pad and operates from 2.7 V to 5.5 V.
Where can I download the AT90CAN128-15MT datasheet PDF?
The AT90CAN128-15MT datasheet is available through the official Microchip Technology AT90CAN128 product page at https://www.microchip.com/en-us/product/AT90CAN128. The automotive data sheet can also be accessed at https://ww1.microchip.com/downloads/en/DeviceDoc/doc7682.pdf. Use the manufacturer documents for the complete pin-description table, electrical limits, timing diagrams, package drawings, programming information, and qualification details applicable to the AT90CAN32/64/128 family.
Where can I find the AT90CAN128 pinout?
The AT90CAN128 pinout is shown in the pin-description table and package drawing in the manufacturer data sheet linked from the official AT90CAN128 product page. The AT90CAN128-15MT uses a 64-QFN package, so its physical pin assignments must be checked against the complete 64-pin diagram rather than inferred from the family description. Assign PCB tracks directly from that pin table and confirm exposed-pad, power, ground, programming, clock, reset, and CAN-interface connections before layout release.
What is the operating voltage of AT90CAN128-15MT?
The AT90CAN128-15MT operates from 2.7 V to 5.5 V. According to the Microchip Technology AT90CAN128 product documentation, this range supports both 3.3 V and 5 V system implementations. The chosen supply must remain within the device electrical limits while also providing adequate startup, reset, clock, and communications margin. A local CAN transceiver may have its own supply and logic-level requirements, so the MCU supply decision should be coordinated with the transceiver and field-interface circuitry.
How much flash memory and RAM does AT90CAN128-15MT contain?
The AT90CAN128-15MT contains 128 KB of ISP flash memory, 4 KB of EEPROM, and 4 KB of SRAM. According to the Microchip Technology AT90CAN128 family documentation, the flash stores executable firmware, the EEPROM preserves nonvolatile configuration data, and the SRAM provides working memory for runtime operations. Firmware sizing should account for the bootloader, CAN drivers, application logic, interrupt vectors, and any in-system programming service before the 128 KB code-memory budget is committed.
Is AT90CAN128-15MT suitable for CAN bus control systems?
Yes, the AT90CAN128-15MT is suitable for CAN bus control because it integrates a CAN 2.0A/V2.0B-compatible controller, 128 KB of program memory, 53 I/O lines, two USARTs, and four timer/counters. According to the Microchip Technology AT90CAN128 documentation, the controller handles CAN frame communication while the AVR core manages local control logic. A separate CAN transceiver is required between the MCU controller pins and the physical CAN bus, together with correct bus termination and signal-integrity layout.
How do I start programming the AT90CAN128?
Programming begins by connecting a compatible AVR programmer to the ISP interface, reset line, target supply, and ground, then loading the application firmware and appropriate fuse settings. The AT90CAN128 supports ISP programming according to the Microchip Technology family data sheet and can also be handled through supported AVR development tools. Before programming, verify the device variant, clock source, boot configuration, brownout behavior, and fuse settings in the manufacturer documentation; the AT90CAN128-15MT identification must match the intended firmware and hardware configuration.
What AT90CAN128 development board is available for prototyping?
An AT90CAN128 development board can be used to evaluate the MCU, CAN controller, programming interface, and communication firmware before porting to a custom PCB. Choose a board that matches the AT90CAN128's 2.7 V to 5.5 V supply range and includes an appropriate CAN transceiver rather than connecting MCU pins directly to the bus. The board documentation should identify the MCU speed grade, oscillator arrangement, debugger or ISP connector, and exposed-pad thermal requirements. Confirm the exact MCU fitted to the board before using AT90CAN128-15MT-specific timing assumptions.
What is the difference between AT90CAN128-15MT and AT90CAN128-16MU?
The primary difference is clock grade: AT90CAN128-15MT operates at up to 15 MHz, while AT90CAN128-16MU operates at up to 16 MHz, a 6.7% increase. The alternative retains the same 64-QFN class of package and the same AT90CAN128 memory and peripheral architecture. Select AT90CAN128-16MU when the design specifically requires 16 MHz timing; otherwise, verify timing margins because changing the clock can affect baud-rate generation, task schedules, filtering, and communication timing.
What can replace AT90CAN128-15MT on the same PCB?
AT90CAN128-15MU and AT90CAN128-15MT1 are the closest same-brand candidates for a footprint-compatible review, while AT90CAN128-16MU offers the same family architecture at a 16 MHz clock grade. According to the Microchip AT90CAN128 family documentation, the 128 KB flash, 4 KB EEPROM, 4 KB SRAM, 53 I/O lines, and CAN 2.0A/V2.0B-compatible controller remain the core architecture. Before substitution, confirm the exact package drawing, exposed pad, temperature grade, clock rating, fuse compatibility, and lifecycle status in the manufacturer ordering information.
Is AT90CAN128-15MT the same as AT90CAN128-16MU?
No. The AT90CAN128-15MT and AT90CAN128-16MU share the AT90CAN128 family architecture and a compatible 64-QFN footprint, but their maximum clock frequencies differ: 15 MHz versus 16 MHz. According to the Microchip Technology family documentation, both provide 128 KB of flash, 4 KB of EEPROM, 4 KB of SRAM, 53 I/O lines, and a CAN 2.0A/V2.0B-compatible controller. The 16 MHz option is the functional choice when existing timing calculations require that additional 6.7% clock headroom.
When should I choose AT90CAN128-15MT over a 16 MHz replacement?
Choose the AT90CAN128-15MT when a design has been validated around the 15 MHz grade and does not require the additional timing headroom of a 16 MHz device. According to the Microchip Technology AT90CAN128 documentation, both grades belong to the same family and retain the core memory, I/O, and CAN resources, but clock-dependent calculations must be checked before changing speed grades. The 15 MHz part can also simplify comparisons with existing firmware timing, provided CAN baud-rate and task-period margins remain acceptable.
Is AT90CAN128-15MT suitable for industrial and automotive embedded control?
The AT90CAN128-15MT is suitable for embedded control applications requiring a CAN controller, 128 KB of flash, and 53 I/O lines. The Microchip AT90CAN32/64/128 automotive data sheet states that product quality and reliability were verified through regular qualification under AEC-Q100. Automotive use should still require confirmation of the exact order code, temperature grade, operating limits, and qualification scope. Industrial designs should verify operating temperature, supply tolerance, EMC requirements, and long-term availability against the specific product documentation.
Where to buy AT90CAN128-15MT online?
The AT90CAN128-15MT can be requested through the Request a Quote form on this page. The form is the appropriate route for current unit availability, quantity breaks, order confirmation, and expected lead time. Engineers should provide the required quantity, target packaging, date code preference, and any quality or traceability requirements. The 64-QFN exposed-pad package and industrial operating context should be confirmed against the manufacturer ordering information before releasing a production purchase order.
What is the current price and stock status of AT90CAN128-15MT?
Current price and stock status for the AT90CAN128-15MT should be confirmed through the Request a Quote form on this page because commercial terms and inventory can change with order quantity and packaging. Submit the required quantity, delivery location, date-code preference, and production schedule for a current quotation. The component is identified as a 15 MHz, 128 KB-flash AVR MCU in a 64-QFN exposed-pad package, so include the complete suffix when requesting the quotation to avoid confusion with other AT90CAN128 order codes.
What is the lead time for AT90CAN128-15MT?
Request the current lead time through the Request a Quote form on this page. Lead time can depend on quantity, date-code requirements, packaging configuration, quality documentation, and current factory allocation. Provide the forecast consumption, requested delivery schedule, and approved-part or traceability requirements so the quotation can reflect the appropriate supply commitment. For new production designs, avoid treating an initial quotation as a long-term allocation guarantee.

के लिए इंजीनियरिंग संदर्भ डेटा AT90CAN128-15MT — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose AT90CAN128-15MT when the board has been designed around the 15 MHz AT90CAN128 grade and needs 128 KB of flash, 4 KB of SRAM, 4 KB of EEPROM, 53 I/O lines, and integrated CAN 2.0A/V2.0B-compatible communications. It is a suitable fit for industrial nodes, vehicle subsystems, building controls, and diagnostic equipment with a confirmed 64-QFN exposed-pad layout. Choose AT90CAN128-15MU or AT90CAN128-15MT1 when the same speed and architecture are required but a different manufacturer ordering code may improve sourcing. Choose AT90CAN128-16MU when the design specifically needs 16 MHz and all timing, baud-rate, and interrupt calculations have been revalidated. AT90CAN128-16AU is another 16 MHz family option, but its exact temperature-grade and ordering details must be checked. No alternative should be released solely from package similarity; verify the pin table, exposed pad, clock configuration, temperature range, qualification scope, and firmware compatibility.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद AT90CAN128-15MU AT90CAN128-15MT1 AT90CAN128-16MU AT90CAN128-16AU
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Package 64-QFN (9 x 9 mm), exposed pad 64-QFN (9 x 9 mm), exposed pad 64-QFN (9 x 9 mm), exposed pad 64-QFN (9 x 9 mm), exposed pad 64-QFN (9 x 9 mm), exposed pad
Maximum Clock Frequency 15 MHz 15 MHz 15 MHz 16 MHz 16 MHz
Flash Memory 128 KB 128 KB 128 KB 128 KB 128 KB
EEPROM 4 KB 4 KB 4 KB 4 KB 4 KB
SRAM 4 KB 4 KB 4 KB 4 KB 4 KB
General-Purpose I/O Lines 53 53 53 53 53
CAN Controller CAN 2.0A/V2.0B compatible CAN 2.0A/V2.0B compatible CAN 2.0A/V2.0B compatible CAN 2.0A/V2.0B compatible CAN 2.0A/V2.0B compatible
Supply Voltage Range 2.7 V to 5.5 V 2.7 V to 5.5 V 2.7 V to 5.5 V 2.7 V to 5.5 V 2.7 V to 5.5 V
USART Count 2 2 2 2 2

मुख्य विशेषताएँ

  • Matches the established 15 MHz AT90CAN128 timing grade (बनामAT90CAN128-16MU)
  • Combines 128 KB flash with CAN connectivity in one MCU (बनामAT90CAN128-16MU)
  • Provides substantial local digital I/O for distributed nodes (बनामAT90CAN128-16AU)
  • SAME-speed family option is available for second-source review (बनामAT90CAN128-15MU)

डिज़ाइन नोट्स

Treat the 64-QFN exposed pad as a mandatory thermal and electrical connection. Follow the Microchip recommended land pattern and place a low-inductance via array within the pad footprint, then connect that region to the ground plane. Avoid splitting the ground plane beneath the package, and keep high-current return paths outside the pad area. The pad provides vertical heat conduction into the PCB, but it cannot replace copper area, via stitching, or airflow needed at elevated ambient temperature.

Implement the PCB from the complete manufacturer pin-description table rather than from the family-level block diagram. Verify power, ground, reset, clock, programming, and CAN-controller assignments directly against the 64-QFN drawing. Keep the exposed-pad via field unobstructed, place decoupling capacitance close to the corresponding supply pins, and preserve the recommended return-current path. A complete pin audit before routing is especially important because exposed-pad packages combine perimeter pins with a large central thermal connection.

Route CAN TX and RX from the MCU to the transceiver as short, referenced traces with continuous return paths, and connect the transceiver to the physical bus through a layout that meets its isolation and termination requirements. Place the bus termination only at the appropriate ends of the network. Keep switching regulators, high-current drivers, clock sources, and long parallel digital routes away from the differential CAN path to reduce radiated noise and susceptibility to common-mode interference.

Do not treat a 16 MHz family member as an automatic substitute for a design validated at 15 MHz. The 6.7% clock increase can change baud-rate error, timer periods, interrupt latency, and communication timing. Preserve the original oscillator and fuse configuration when possible, recalculate all timing-dependent behavior, and run CAN stress tests before releasing the higher-clock alternative. Likewise, verify the exact temperature grade and ordering-code meaning for each MT, MU, and AU suffix.

अनुपालन जानकारी

RoHS
Compliant
REACH
Unknown
AEC-Q100
Qualified
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

The Microchip AT90CAN32/64/128 automotive data sheet states that product quality and reliability were verified through regular product qualification under AEC-Q100. RoHS status is compliant; other environmental declarations are not established by the cited documentation.

डेटा सत्यापन तिथि: 2026-11-20 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

at90can128 datasheet at90can128 pinout at90can128 16au datasheet at90can128 programming at90can128 development board at90can128 pdf AT90CAN128-15MT datasheet AT90CAN128-15MT pinout AT90CAN128-15MT equivalent AT90CAN128-15MT replacement AT90CAN128-15MT vs AT90CAN128-16MU AT90CAN128-15MT 64-QFN footprint AT90CAN128-15MT CAN controller AT90CAN128-15MT price AT90CAN128-15MT stock

संबंधित कंपोनेंट्स और शब्द

Microchip Technology AT90CAN128 AT90CAN128-15MT AT90CAN128-15MU AT90CAN128-15MT1 AT90CAN128-16MU AT90CAN128-16AU AVR AVR enhanced RISC architecture 8-bit microcontroller embedded microcontroller semiconductor CAN controller CAN 2.0A CAN 2.0B Industry Standard CAN ISP flash memory EEPROM SRAM USART Two-Wire Interface real-time counter timer/counter 64-QFN QFN family surface mount exposed pad AEC-Q100 RoHS automotive control industrial automation CAN bus
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें