BCM8155FAIFBG - 11.352 Gbps XFI Transceiver | Broadcom
MPN: BCM8155FAIFBG ✓ सक्रियBCM8155FAIFBG अवलोकन
An XFI transceiver is a high-speed interface IC that converts parallel or serial logic into a physical serial channel and receives data from that channel. It belongs to the broader hierarchy of transceiver, communication interface, interface IC, and semiconductor products. The BCM8155 operates in demanding data-center, telecom, and industrial communication systems where link margin, standards compliance, and diagnostic coverage are important design considerations.
Key features include support for OIF, Telcordia, ITU-T, XFI, and IEEE 802.3ae requirements. Its supported range of 8.5 Gbps to 11.352 Gbps supports 10G-class and related high-speed serial links. Input sensitivity is specified at 10 mV peak-to-peak, which provides a defined receiver sensitivity reference for link-budget calculations. The device also provides loopbacks, a pattern generator, and a pattern checker for fault isolation and board-level validation.
The BCM8155 is intended for optical-module, backplane, router, switch, and test-equipment designs where a standardized XFI interface helps simplify interoperability between high-speed PHY or ASIC subsystems. Its diagnostic features allow engineers to isolate transmitter, receiver, pattern-generation, and pattern-verification failures without relying only on external instrumentation. RZ modulation support can provide additional flexibility for long-haul transmission and signal-integrity optimization.
When designing around this transceiver, use the manufacturer pin-description and reference-circuit information to assign power, ground, signal, control, and test pins. Confirm the completed channel budget against 11.352 Gbps operation and the receiver sensitivity requirement. Review termination, differential routing, connector or optical-interface transitions, and return-path continuity before releasing the PCB layout. The device should be treated as a precision high-speed component, with controlled impedance and short return paths especially important in multilayer designs.
के लिए ड्रॉप-इन विकल्प BCM8155FAIFBG — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस उत्पाद के लिए कोई drop-in alternatives उपलब्ध नहीं।
विकल्प अनुरोध करेंBCM8155FAIFBG Maximum Ratings और Electrical Characteristics
| कोई specifications उपलब्ध नहीं |
BCM8155FAIFBG standard पिन कॉन्फ़िगरेशन गाइड
BCM8155FAIFBG (standard पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस एनालॉग कंपोनेंट में इनपुट, आउटपुट और पावर सप्लाई पिन हैं। ऑफ़सेट नल, कम्पनसेशन और एनेबल पिन कॉन्फ़िगरेशन के लिए निर्माता डेटाशीट देखें। सिग्नल कंडीशनिंग और एम्प्लीफ़ायर सर्किट के लिए आदर्श।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: BCM8155FAIFBG.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
BCM8155FAIFBG के लिए उपयुक्त है 6 अनुप्रयोगs: 10G-Class Optical Module Interfaces, Router and Switch Line Cards, Telecom Backplane Links, Data-Center Interconnect Equipment, High-Speed Test and Measurement Systems, Industrial High-Speed Control Systems.
10G-Class Optical Module Interfaces
BCM8155FAIFBG fits high-speed optical-module interfaces that need an XFI connection between a transceiver module and an ASIC or line-card controller. Its 8.5 Gbps to 11.352 Gbps range covers the operating envelope for 10G-class serial links, while RZ modulation capability provides additional long-haul design flexibility. The 10 mV peak-to-peak input sensitivity is useful when closing the receiver link budget against module output, connector loss, and channel loss. In implementation, the reference network and differential routing must be controlled closely, and the pattern checker can verify recovered data during bring-up.
अनुशंसित
Router and Switch Line Cards
BCM8155FAIFBG is appropriate for router and switch line cards requiring a standardized XFI interface to high-speed optical or copper-channel subsystems. The operating range of 8.5 Gbps to 11.352 Gbps supports modern 10G-class transport links, while the available RZ option can assist long-haul channel design. In a line card, the transceiver works beside a packet-processing ASIC, clocking circuitry, and physical-layer devices. Controlled impedance, continuous ground references, and minimized crosstalk are essential because the XFI signal margin depends on the complete channel rather than on the IC alone.
अनुशंसित
Telecom Backplane Links
BCM8155FAIFBG supports telecom backplane and equipment links that operate at high serial rates and benefit from long-haul transmission capability. Its selectable RZ transmitter modulation gives system designers another signaling choice when evaluating channel margin, while the 10 mV peak-to-peak receiver sensitivity provides a defined budget input. Deployment in a backplane requires careful treatment of insertion loss, connector transitions, skew, crosstalk, and return-path discontinuities. The built-in loopback, pattern generator, and pattern checker support commissioning and fault isolation after the system is assembled.
अनुशंसित
Data-Center Interconnect Equipment
BCM8155FAIFBG can be used in data-center interconnect equipment where an ASIC, switching fabric, or aggregation engine requires a high-speed XFI connection to an optical interface. The device supports 8.5 Gbps to 11.352 Gbps and provides diagnostic functions that help identify failures in complex systems. Designers should validate the complete channel against receiver sensitivity and transmitter specifications, then account for thermal conditions and power delivery near the transceiver. Controlled-impedance routing and a short, continuous ground path help preserve signal quality across multilayer boards.
अनुशंसित
High-Speed Test and Measurement Systems
BCM8155FAIFBG is suitable for test and measurement equipment that must exercise high-speed serial links, emulate traffic, and isolate faults. The integrated pattern generator produces controlled test data, the pattern checker evaluates the received sequence, and loopback modes support focused troubleshooting of transmitter and receiver paths. These capabilities can shorten board-level validation compared with systems that depend entirely on external pattern sources. The instrument enclosure still needs a controlled thermal environment and an appropriate high-speed interface, while the PCB must preserve controlled impedance and minimize discontinuity at every connection.
अनुशंसित
Industrial High-Speed Control Systems
BCM8155FAIFBG can support industrial control and monitoring systems that exchange data over a long-haul serial link rather than relying only on a short board-level interface. The supported 8.5 Gbps to 11.352 Gbps range and optional RZ modulation provide a high-performance transport foundation, while the diagnostic functions improve field and manufacturing troubleshooting. Because industrial environments may include vibration, temperature variation, and electromagnetic coupling, the installation should be validated at the system level. Cable or optical transitions, grounding, shielding, and power filtering all influence the practical link margin.
अनुशंसित
के लिए इंजीनियरिंग संदर्भ डेटा BCM8155FAIFBG — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद |
|---|---|
| Brand | Broadcom |
| Supported Data Rate | 8.5 Gbps to 11.352 Gbps |
| Maximum Data Rate | 11.352 Gbps |
| Input Sensitivity | 10 mV peak-to-peak |
| Interface | XFI |
| Transmitter Modulation | RZ modulation capable |
| Fault Isolation | Loopbacks, pattern generator, and pattern checker |
| Standards Compliance | OIF, Telcordia, ITU-T, XFI, IEEE 802.3ae |
मुख्य विशेषताएँ
- Broad supported operating range (बनामNo confirmed drop-in alternative)
- Long-haul modulation flexibility (बनामNo confirmed drop-in alternative)
- Integrated diagnostic coverage (बनामNo confirmed drop-in alternative)
डिज़ाइन नोट्स
Use the manufacturer reference layout to control differential impedance, via transitions, return paths, and the placement of the external interface network. At rates as high as 11.352 Gbps, small discontinuities can affect edge quality and link margin. Keep the high-speed path compact, avoid abrupt width changes, maintain a continuous ground reference, and review the design with an appropriate signal-integrity model before fabrication.
Build the channel budget around the 10 mV peak-to-peak receiver-sensitivity reference and include transmitter output, connector or optical-path loss, insertion loss, jitter, and crosstalk. Account for the exact 8.5 Gbps to 11.352 Gbps operating range rather than assuming all system margins remain constant. If channel loss is high, evaluate the available RZ modulation option and use the loopback and pattern-checking facilities to isolate whether degradation originates in the link or the transceiver.
Do not treat XFI, OIF, Telcordia, ITU-T, or IEEE 802.3ae references as permission to substitute any device with a similar package name. A valid replacement must have verified pin mapping, electrical ratings, timing, supported rates, receiver sensitivity, modulation behavior, and mechanical compatibility. After board assembly, use the pattern generator and checker before declaring the link operational, and separate transmitter, receiver, and interconnect faults with the available loopback modes.
अनुपालन जानकारी
The BCM8155 technical description identifies OIF, Telcordia, ITU-T, XFI, and IEEE 802.3ae compliance. Component-level RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations require confirmation from current manufacturer documentation.