CD4067BPW - 16:1 CMOS Analog Multiplexer | Texas Instruments
MPN: CD4067BPW ✓ सक्रियCD4067BPW अवलोकन
An analog multiplexer is a semiconductor switching network that combines multiple signal paths into a shared input or output. The CD4067B belongs to the CMOS analog switch, multiplexer, and demultiplexer hierarchy, where its bidirectional switch paths can distribute analog signals in either direction. On-chip binary decoding reduces the external control logic required to select one of 16 channels, making the device useful for data acquisition, test systems, and signal-routing equipment.
The principal electrical features include a 20 V maximum supply rating, 3 V to 18 V operating supply range, 125-ohm typical ON resistance, and 240-ohm maximum ON resistance. The typical ON resistance falls to 5 ohms when VDD minus VSS is 15 V. Typical quiescent power dissipation is listed as 0.2 microwatts at a 10 V supply, while a distributor specification lists quiescent current at 100 microamperes.
The CD4067B uses four address inputs to decode one of 16 channels. A common inhibit and an enable control govern whether the selected path is active. Its CMOS switch architecture supports bidirectional signal routing, allowing the same device to function either as a multiplexer or a demultiplexer. The result is a compact analog routing element for systems that need more input or output channels than the controlling converter directly provides.
Typical applications include multiplexed sensor acquisition, automated test-equipment routing, data-converter channel selection, sample-and-hold systems, and industrial control interfaces. The device is especially useful when several low-bandwidth or moderate-bandwidth analog signals must share a downstream ADC, amplifier, measurement front end, or communications interface.
Designers should verify signal amplitude against the supply rails, account for ON resistance when calculating source-load attenuation, and use the enable and inhibit controls to prevent unintended channel selection. Decoupling capacitors should be placed close to the supply pins, while sensitive signals require short, guarded routing to minimize coupling into the high-impedance control paths.
This product page combines the manufacturer and distributor specifications with practical routing guidance, pin-location guidance, package details, and a parameter-by-parameter comparison of documented drop-in alternatives for faster engineering selection.
के लिए ड्रॉप-इन विकल्प CD4067BPW — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
CD4067BPWG4
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
CD4067BPWRG4
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
CD4067BPW विशेषताएं
| Multiplexer Configuration | 1 x 16:1 |
| Number of Channels | 16 channels |
| Multiplexer Type | Single-channel analog multiplexer/demultiplexer |
| Supply Voltage Range | 3 V to 18 V |
| Maximum Supply Voltage | 20 V |
| ON Resistance | 125 ohms typical |
| Maximum ON Resistance | 240 ohms |
| ON Resistance at VDD - VSS = 15 V | 5 ohms typical |
| क्वाइसेंट करंट | 100 microamperes |
| Quiescent Power Dissipation | 0.2 microwatts typical at VDD - VSS = 10 V |
| Address Inputs | 4 binary address inputs |
| Signal Routing | Bidirectional |
| पैकेज | 24-pin TSSOP |
| माउंटिंग प्रकार | Surface mount |
| Shipping Package | Tube |
CD4067BPW tube पिन कॉन्फ़िगरेशन गाइड
CD4067BPW (tube पैकेज) के लिए पिन कॉन्फ़िगरेशन। पिन नंबरिंग, फ़ंक्शन और कनेक्शन आरेख निर्माता डेटाशीट में परिभाषित हैं। सटीक फुटप्रिंट और सोल्डरिंग दिशानिर्देशों के लिए इसे देखें।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: CD4067BPW.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
CD4067BPW के लिए उपयुक्त है 6 अनुप्रयोगs: Multiplexed Sensor Acquisition, Automated Test Equipment Routing, Data Converter Channel Selection, Industrial Control Signal Routing, Sample-and-Hold Signal Selection, Programmable Signal Distribution.
Multiplexed Sensor Acquisition
The CD4067BPW fits sensor-frontend designs that must bring up to 16 analog inputs into one shared ADC or instrumentation amplifier. Its four address inputs allow a microcontroller to select a channel without operating 16 separate analog switches, while the 125-ohm typical ON resistance is useful for moderate-impedance sources. Account for the maximum 240-ohm resistance when driving high-impedance sensors, and place a buffer near the sensor if source impedance or ADC settling time is high. The enable and inhibit controls can also isolate the mux during sensor-settle or calibration intervals.
अनुशंसित
Automated Test Equipment Routing
The CD4067BPW is useful in automated test equipment where a controller must route one of 16 test or measurement paths to a common measurement channel. Its 16:1 organization provides more routing density than an eight-channel multiplexer, and the integrated address decoder simplifies control sequencing. Route sensitive test nodes carefully because the ON resistance can introduce attenuation and thermal noise, while long PCB traces may couple interference into high-impedance inputs. The bidirectional switch paths also support signal routing in either direction.
अनुशंसित
Data Converter Channel Selection
The CD4067BPW can connect several conditioned analog inputs to a shared data-converter input, reducing the number of external routing components required by the system. The 16:1 architecture is particularly effective for sensor, diagnostic, or industrial-control channels that do not require simultaneous high-bandwidth sampling. Account for the mux's maximum 240-ohm ON resistance when budgeting source impedance, ADC acquisition time, and gain error. A local buffer near the multiplexer output can isolate the ADC sample-and-hold input during switching transitions.
अनुशंसित
Industrial Control Signal Routing
The CD4067BPW supports industrial control systems that distribute control, feedback, or diagnostic signals across a shared analog bus. Its 3 V to 18 V operating range accommodates common supply arrangements, and on-chip address decoding allows straightforward selection from a microcontroller or programmable counter. Design the signal path so its common and channel terminals remain within the device's valid analog range. For safety-critical isolation, keep the CD4067BPW on the non-isolated field side and use appropriately rated isolation components at the system boundary.
अनुशंसित
Sample-and-Hold Signal Selection
The CD4067BPW can select one of 16 source signals for a sample-and-hold stage when several slowly changing or multiplexed measurements share one amplifier path. Its typical ON resistance of 125 ohms is low enough for many conventional sample-and-hold networks, but designers should include switch resistance in the acquisition-time and droop calculations. Use the inhibit and enable controls to command a defined settling interval after changing the four address bits. For fast-moving inputs, verify bandwidth and charge-injection requirements against the manufacturer switching data.
अनुशंसित
Programmable Signal Distribution
The CD4067BPW works in programmable signal-distribution systems that route one of 16 sources to a shared destination under digital control. Because the switch paths are bidirectional, the same architecture can support source selection or signal distribution according to the board topology. The integrated four-bit address decoder reduces external decoding logic, while the compact 24-pin TSSOP supports dense control boards. Keep supply decoupling close to VDD and VSS, provide a defined logic reference, and avoid driving the address, enable, or inhibit inputs beyond their specified voltage limits.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा CD4067BPW — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | CD4067BPWG4 | CD4067BPWRG4 |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 24-pin TSSOP | 24-pin TSSOP - same package | 24-pin TSSOP - same package |
| Multiplexer Configuration | 1 x 16:1 | 1 x 16:1 | 1 x 16:1 |
| Number of Channels | 16 channels | 16 channels | 16 channels |
| Address Decoding | On-chip binary decoding | On-chip binary decoding | On-chip binary decoding |
मुख्य विशेषताएँ
- Higher routing density in the same TSSOP footprint (बनामCD4097BPWRE4)
- Bidirectional multiplexer and demultiplexer operation (बनामCD4097BPWRE4)
- Integrated binary address decoding (बनामCD4067BPWG4)
डिज़ाइन नोट्स
Do not treat the maximum 240-ohm ON resistance as a constant value across all supply conditions; the manufacturer information lists 125 ohms typical and approximately 5 ohms typical at a 15 V VDD-minus-VSS difference. Include the actual switch resistance in source impedance, ADC settling-time, and gain-error calculations. For high-impedance sensors, add a nearby buffer rather than allowing the mux resistance to dominate the signal path.
Place the supply bypass capacitor directly between VDD and VSS pins, with a short ground return, and keep the common and selected-channel routes away from clock, address, and high-current switching nodes. Although the chip has integrated address decoding, the four address inputs still require clean return paths. Use a solid ground plane and avoid routing sensitive analog channels beneath digital control traces where coupling could disturb the selected measurement.
Allow the analog path to settle after changing the address code before capturing a sample. Account for the mux ON resistance together with the capacitance of the downstream node and the source impedance of the selected signal. When multiplexing high-frequency or large-amplitude signals, verify the signal amplitude against the supply limits and consult the manufacturer switching-characteristics table before selecting sampling timing.
Use the enable and inhibit controls to place the mux in a defined state during reset, configuration, and measurement transitions. Ensure every address, enable, and inhibit signal remains within the valid logic-input range referenced to VSS. Keeping unused or sensitive channels in a controlled state reduces accidental signal injection and makes system behavior more predictable during startup and fault recovery.
अनुपालन जानकारी
No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals status was identified for the exact orderable MPN. AEC-Q100 is not applicable because CD4067BPW is an industrial CMOS analog multiplexer rather than an automotive-qualified device.