CD4520BCN - Dual 4-Bit Binary Up-Counter | onsemi
MPN: CD4520BCN ✓ सक्रियCD4520BCN अवलोकन
A CMOS binary counter is a sequential logic device that tracks a binary number from one clock event to the next. It belongs to the logic IC hierarchy: counter → binary counter → digital counter → logic IC → semiconductor. The CD4520BCN contains two identical 4-stage counters, allowing one package to provide independent counting channels or to implement a wider 8-bit counting arrangement when the sections are cascaded.
Key features include dual 4-bit up-counting, positive-edge triggering, a maximum count of 15 per section, and operation across a 3 V to 15 V supply range. Its internal counter stages are D-type flip-flops with interchangeable clock and enable lines, giving designers control over when counting advances and when the count is held. The device is offered in a 16-pin PDIP package for through-hole PCB assembly.
The CD4520BCN is designed for low-power digital control, timing, sequencing, and state-counting systems. Because its counter sections are independently synchronous, each section advances on the selected active clock edge when its enable condition is satisfied. Cascading the sections extends the count range beyond the native 4-bit capacity, while separate clock inputs permit two unrelated counters to share one package.
Typical uses include industrial timing modules, laboratory pulse counters, programmable-delay circuits, digital instrumentation, event-counting interfaces, and digital control systems. The device can also serve as a programmable binary divider when additional logic conditions the clock and enable inputs.
Designers should account for unused counter inputs, provide suitable bypassing around the power pins, and confirm that clock and reset waveforms satisfy the manufacturer’s timing requirements. Because the counter operates in the legacy CMOS 4000-series family, verify input levels and timing margins against the system supply voltage before using it with modern 3.3 V or 5 V logic.
This page combines the CD4520BCN’s key operating characteristics, package details, drop-in replacement analysis, application guidance, and practical design notes to support faster component selection and board-level implementation.
के लिए ड्रॉप-इन विकल्प CD4520BCN — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस सीरीज़ के वेरिएंट
समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं CD4520BCN (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Logic Family, Mounting Type, Output Type, Package, Supply Voltage Range.
CD4520BCE
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
CD4520BC
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
MC14520BCL
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
MC14520B
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
CD4520BEE4
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
CD4520BD
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →CD4520BCN Maximum Ratings और Electrical Characteristics
| Product Type | Dual 4-bit binary up-counter |
| Number of Counter Sections | 2 sections |
| Counter Resolution | 4 bits per section |
| Internal Stage Count | 4 stages per counter |
| Counting Direction | Up counter |
| Triggering Edge | Positive-edge triggered |
| Maximum Terminal Count | 15 per section |
| Supply Voltage Range | 3 V to 15 V |
| आउटपुट प्रकार | Binary counter outputs |
| Temperature Grade | Industrial |
| Terminal Form | Through-hole |
| Number of Terminals | 16 terminals |
| Package Code | DIP |
| Package Shape | Rectangular |
| पैकेज | PDIP-16 |
| माउंटिंग प्रकार | Through-hole |
| Logic Family | 4000-series CMOS |
CD4520BCN pdip-16 पिन कॉन्फ़िगरेशन गाइड
CD4520BCN (pdip-16 पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस डिजिटल IC में GPIO, संचार इंटरफ़ेस (UART, SPI, I2C) और पावर पिन शामिल हैं। वैकल्पिक पिन फ़ंक्शन और कॉन्फ़िगरेशन विकल्पों के लिए निर्माता डेटाशीट देखें। एम्बेडेड सिस्टम डिज़ाइन और PCB लेआउट के लिए आवश्यक।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: CD4520BCN.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
CD4520BCN के लिए उपयुक्त है 6 अनुप्रयोगs: Industrial Pulse Counter, Programmable Timer and Delay, Digital Instrumentation, Digital Sequence Control, Laboratory Event Counter, Frequency Divider.
Industrial Pulse Counter
The CD4520BCN suits industrial pulse-counting modules because it provides two independent 4-bit counters, a 3 V to 15 V supply range, and positive-edge-triggered counting. Each section can count sensor-derived pulses up to 15 before rollover, allowing two event channels to share one 16-pin DIP package. Configure reset and enable inputs to establish a known starting state and prevent unwanted increments. The principal design consideration is edge cleanliness: switch bounce or asynchronous transitions near a clock edge can produce an incorrect count, so filtering and source synchronization may be required before the counter inputs.
अनुशंसित
Programmable Timer and Delay
The CD4520BCN can implement a programmable timer when its clock is driven by a periodic reference and its count output is decoded by external logic. Two 4-bit sections allow parallel timing intervals or cascaded count ranges extending beyond 15 clock events. Positive-edge triggering makes clock polarity and source selection central to implementation. The counter’s maximum terminal count of 15 must be considered when defining the delay interval, while the enable and reset controls determine when timing begins and whether an output remains stable. A clean, jitter-controlled reference clock improves repeatability.
अनुशंसित
Digital Instrumentation
The CD4520BCN is useful in digital instrumentation that counts test cycles, measurement intervals, or sequential test steps. Two independent 4-bit counting sections can handle separate measurement phases within a shared instrument while preserving a compact through-hole footprint. The 3 V to 15 V operating range allows use in legacy laboratory and industrial control systems, although the entire signal chain must use compatible logic levels. Designers should establish reset behavior at power-up, decode binary outputs for display or control, and avoid presenting an unverified pinout assumption to the PCB layout.
अनुशंसित
Digital Sequence Control
The CD4520BCN can form part of a repeatable digital sequence controller by counting command or timing events and decoding the four binary outputs into discrete states. One section can track a primary sequence while the second counts a related phase or provides a rollover event. Its industrial temperature grade and positive-edge clocking support control systems operating across conventional CMOS supply voltages. The design must prevent illegal counter states through reset logic, and output decoding should use non-overlapping states. Cascading is useful when the required sequence length exceeds the native 16-count range.
अनुशंसित
Laboratory Event Counter
The CD4520BCN is appropriate for a laboratory event counter requiring two compact, independently clocked binary count channels. It can count experiment cycles, actuator movements, or logic-generated test events while retaining four-bit state information for downstream display or control. The PDIP-16 package simplifies through-hole prototyping and repair. For accurate results, the event source should present clean transitions, reset should be asserted long enough to initialize both sections, and the maximum count of 15 per channel must be included in the readout or rollover logic. Cascading provides additional range when the application requires it.
अनुशंसित
Frequency Divider
The CD4520BCN can function as a programmable frequency divider by driving its clock with the signal to be divided and decoding a selected count output. The 4-bit counter provides eight divide ratios from 2 through 16, and cascading its two sections extends the selectable range. Positive-edge triggering helps define the relationship between source transitions and count advancement. Designers must account for propagation delay, reset timing, and any counter enable behavior when cascading sections. Because the device is a legacy CMOS logic part, the divider should remain within the manufacturer’s stated supply and input-level limits.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा CD4520BCN — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | CD4520BCN | CD4520BCE | CD4520BC | MC14520BCL | CD4520BEE4 | CD4520B |
|---|---|---|---|---|---|---|---|
| Brand | onsemi | onsemi | onsemi | onsemi | onsemi | Texas Instruments | Texas Instruments |
| Package | PDIP-16 | PDIP-16 | PDIP-16 | PDIP-16 | PDIP-16 | PDIP-16 | PDIP-16 |
| Counter Type | Dual 4-bit binary up-counter | Dual 4-bit binary up-counter | Dual 4-bit binary up-counter | Dual 4-bit binary up-counter | Dual 4-bit binary up-counter | Dual 4-bit binary up-counter | Dual 4-bit binary up-counter |
| Number of Counter Sections | 2 sections | 2 sections | 2 sections | 2 sections | 2 sections | 2 sections | 2 sections |
| Counter Resolution | 4 bits per section | 4 bits per section | 4 bits per section | 4 bits per section | 4 bits per section | 4 bits per section | 4 bits per section |
| Maximum Terminal Count | 15 per section | 15 per section | 15 per section | 15 per section | 15 per section | 15 per section | 15 per section |
| Triggering Edge | Positive-edge triggered | Positive-edge triggered | Positive-edge triggered | Positive-edge triggered | Positive-edge triggered | Positive-edge triggered | Positive-edge triggered |
| Mounting Type | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole |
मुख्य विशेषताएँ
- Two independent counting sections in one package (बनामSN74LS93DR)
- Broad CMOS supply range (बनामCD4520BEE4)
- Native 4-bit terminal count (बनामSN74LS90DR)
डिज़ाइन नोट्स
Treat clock, enable, and reset inputs as synchronous control signals. Hold reset for the interval required by the manufacturer’s timing diagram, and do not allow clock edges to occur near a reset transition. A clean reset release reduces the chance that the counter advances into an unintended state. When a noisy switch or sensor drives the clock, add filtering or synchronization before the input; otherwise contact bounce can be interpreted as multiple count events.
Place the bypass capacitor close to the device supply pins and route ground returns directly to the device ground pins. Keep clock traces away from switching nodes and output traces that change rapidly at count rollover. Because this is a through-hole PDIP device, verify the physical pin orientation, row spacing, and pin numbering against the package drawing before inserting it into the board.
Do not assume the two sections are automatically cascaded: each counter requires the correct connection between its own clock, enable, reset, and output pins. Confirm whether counting should advance on the selected positive edge and whether the enable input is active high or low for the selected configuration. Also account for the 4-bit rollover from 15 to 0 in software, decoding logic, and any downstream interrupt scheme.
अनुपालन जानकारी
The component is identified as an industrial-grade logic IC. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current manufacturer product documentation.