CY8C3246PVI-141 8-Bit PSoC 3 MCU 64KB Flash | Infineon
MPN: CY8C3246PVI-141 ✗ जीवन की समाप्तिCY8C3246PVI-141 अवलोकन
A PSoC, or programmable system-on-chip, is a microcontroller platform that combines a CPU core, memory, programmable digital logic, analog blocks, and communication peripherals on one integrated circuit. The PSoC family hierarchy is microcontroller, embedded microcontroller, programmable system-on-chip, and semiconductor. The CY8C3246PVI-141 belongs to the PSoC 3 family and is identified as using an 8-bit 8051 processing core. This architecture is intended for embedded products requiring deterministic control, flexible peripheral configuration, and reduced board complexity without the overhead of a large application processor.
The available manufacturer listing identifies the target as an 8-bit MCU with 64 kByte flash and a 48-SSOP package. The cross-reference listing also identifies a related CY8C3246PVI-147 device as a PSoC 3 MCU with an 8-bit 8051 core, 64 kByte flash, 8 kByte SRAM, and operation up to 50 MHz. The exact electrical limits, clock options, analog performance, temperature rating, and package dimensions for CY8C3246PVI-141 are not printed in the supplied manufacturer-page extract and therefore require confirmation from the manufacturer datasheet before design release.
The CY8C3246PVI-141 can be used as the central controller in sensor-reading systems, keypad interfaces, motor-control peripherals, lighting controllers, and compact industrial control modules. Its programmable mixed-signal resources can reduce the number of discrete analog and digital building blocks when the final peripheral configuration is known. Engineers should select capacitors, external clock components, communications lines, and power rails according to the exact datasheet schematic rather than assuming that generic PSoC 3 guidance applies to every package variant.
The PSoC 3 programming ecosystem is an important part of the device selection. The programmer listing identifies ISP-SWD programming for CY8C3246PVI-141, providing a concrete indication that serial programming through SWD is supported for this device. In production designs, programming access, boot behavior, reset handling, and debugger connections should be planned early because these details can affect connector count, test coverage, and firmware update procedures.
A critical mechanical consideration is the 48-SSOP footprint. The supplied 48-SSOP identity does not correspond to an exact package diagram in the available package library, so the package illustration should be treated as a placeholder until the manufacturer drawing is used for land-pattern design. Verify pin numbering, pin 1 orientation, lead pitch, body dimensions, maximum soldering temperature, and exposed-pad requirements against the official datasheet and package drawing.
This page combines the identified PSoC 3 core, memory, package, programming method, lifecycle context, and engineering trade-offs with design guidance and a structured comparison framework. It is intended to accelerate component search while keeping unknown electrical and mechanical limits clearly separated from confirmed product facts.
के लिए ड्रॉप-इन विकल्प CY8C3246PVI-141 — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस उत्पाद के लिए कोई drop-in alternatives उपलब्ध नहीं।
विकल्प अनुरोध करेंCY8C3246PVI-141 Maximum Ratings और Electrical Characteristics
| Product Type | Programmable System-on-Chip (PSoC 3) microcontroller |
| CPU Core | 8-bit 8051 core |
| Flash Memory | 64 kByte |
| SRAM | 8 kByte |
| Maximum CPU Frequency | 50 MHz |
| पैकेज | 48-SSOP |
| माउंटिंग प्रकार | Surface mount |
| Programming Interface | ISP-SWD |
| Product Family | PSoC 3 |
| Manufacturer | Infineon Technologies |
| Original Brand | Cypress Semiconductor |
CY8C3246PVI-141 48-ssop पिन कॉन्फ़िगरेशन गाइड
CY8C3246PVI-141 (48-ssop पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस डिजिटल IC में GPIO, संचार इंटरफ़ेस (UART, SPI, I2C) और पावर पिन शामिल हैं। वैकल्पिक पिन फ़ंक्शन और कॉन्फ़िगरेशन विकल्पों के लिए निर्माता डेटाशीट देखें। एम्बेडेड सिस्टम डिज़ाइन और PCB लेआउट के लिए आवश्यक।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: CY8C3246PVI-141.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
CY8C3246PVI-141 के लिए उपयुक्त है 6 अनुप्रयोगs: Industrial Sensor Interface, Compact Human Interface Controller, Motor and Actuator Control, LED Lighting Controller, Battery-Powered Sensor Node, USB-to-Consumer Peripheral Bridge.
Industrial Sensor Interface
The CY8C3246PVI-141 can serve as the embedded controller in a compact sensor-interface module because the PSoC 3 architecture combines an 8-bit 8051 core with programmable mixed-signal resources. The identified 64 kByte flash provides room for acquisition routines, calibration logic, filtering, diagnostics, and a communications stack, while 8 kByte SRAM supports working buffers and state-machine execution. Engineers can configure digital logic and analog functions around the measurement rather than using a fixed peripheral arrangement. Before layout, confirm the exact analog input range, ADC performance, operating temperature, supply voltage, and 48-SSOP pin assignments in the manufacturer datasheet.
अनुशंसित
Compact Human Interface Controller
The CY8C3246PVI-141 is suitable for keypad, button, display, and menu-control modules where a compact mixed-signal controller can reduce the number of separate components. Its 8-bit 8051 processing core and 64 kByte flash are appropriate for debouncing, state management, indicator control, and configuration storage, while programmable digital blocks can implement timing or interface functions. The 48-SSOP footprint supports dense assemblies but requires careful escape routing. Designers should verify GPIO count, pin-multiplexing limits, external pull requirements, and display timing before selecting it, using the manufacturer pin table as the PCB authority.
अनुशंसित
Motor and Actuator Control
The CY8C3246PVI-141 can control small motors, relays, solenoids, and other actuators in compact embedded products. Its 8-bit 8051 core can execute motion sequences, fault handling, and digital control logic, while the PSoC platform allows timing-sensitive functions to be placed in programmable digital blocks. The 64 kByte flash supports a control application plus diagnostics, and 8 kByte SRAM is useful for state tables and command processing. The system design must include suitable driver circuitry, protection, and decoupling; verify pin drive limits, timing peripherals, supply requirements, and thermal conditions against the official documentation.
अनुशंसित
LED Lighting Controller
The CY8C3246PVI-141 can serve as the logic controller in an LED lighting module, coordinating button inputs, status indicators, dimming commands, and fault reporting. Its programmable digital resources are useful for deterministic timing, while the 8-bit core can manage lighting profiles and serial configuration commands. The 64 kByte flash and 8 kByte SRAM are sufficient for compact embedded control firmware when the application is appropriately partitioned. LED drive transistors and current-setting networks remain external, so designers must verify GPIO drive capability, PWM or timer availability, pin assignments, and supply behavior in the manufacturer documentation before production release.
अनुशंसित
Battery-Powered Sensor Node
The CY8C3246PVI-141 can form the control core of a low-power sensor node when the product requires the flexibility of a PSoC 3 mixed-signal architecture rather than a minimal microcontroller. Its programmable resources can consolidate acquisition, thresholding, and intermittent control behavior, while the 64 kByte flash stores firmware and configuration data. Energy optimization still depends on the exact device sleep modes, active current, and analog-block behavior, which must be confirmed from the datasheet. Use the Request a Quote form for availability and define the battery, duty cycle, and sensor interface before committing to the architecture.
अनुशंसित
USB-to-Consumer Peripheral Bridge
The CY8C3246PVI-141 can support compact consumer accessories that need protocol conversion, configuration handling, and control functions. Its embedded 8051 core can manage device state, while programmable digital logic can assist with protocol timing and status handling. The 64 kByte flash is useful for firmware updates and configuration tables, and the 48-SSOP package supports board-space reduction. USB compliance depends on the exact PSoC 3 peripheral configuration and board implementation, so the design must follow the manufacturer reference schematic. Confirm supported USB features, electrical limits, clocking, power, and exposed programming pins before declaring USB compliance.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा CY8C3246PVI-141 — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद |
|---|---|
| Brand | Infineon Technologies |
| Package | 48-SSOP |
| Product Type | PSoC 3 programmable system-on-chip |
| CPU Core | 8-bit 8051 |
| Flash Memory | 64 kByte |
| SRAM | 8 kByte |
| Maximum CPU Frequency | Up to 50 MHz |
| Programming Interface | ISP-SWD |
| Mounting Type | Surface mount |
मुख्य विशेषताएँ
- Integrated programmable mixed-signal architecture (बनामATMEGA44A-MUR)
- Family memory configuration (बनामATMEGA48A-CCU)
- Explicit programming-method support (बनामATMEGA32-16AU)
डिज़ाइन नोट्स
Treat the 48-SSOP package drawing as the mechanical source of truth because the available package library does not include a matching 48-SSOP illustration. Before routing, verify body dimensions, lead pitch, pin-one orientation, solder-mask clearance, and copper-to-copper spacing. Confirm every signal on the manufacturer pin-description table, especially programming and reset pins, because a mechanically similar footprint does not establish electrical compatibility.
Use the manufacturer power recommendations for bypass capacitance, permitted supply voltage, startup behavior, and pin sequencing. Place required input and output capacitors adjacent to the specified device pins and keep high-current return paths away from sensitive analog routing. Validate brownout, reset, and power-consumption behavior across the complete operating voltage and temperature range rather than relying only on nominal test conditions.
Do not assume that every CY8C3246PVI ordering code is a drop-in substitute for CY8C3246PVI-141. Package naming, temperature grade, clock marking, qualification, and lifecycle terms can differ even when the core and memory descriptions match. Obtain the manufacturer ordering table, compare every pin and programmed configuration, and verify ISP-SWD connectivity before approving a cross-code replacement.
Preserve access to ISP-SWD programming signals and provide a stable ground reference for debug and manufacturing operations. If the design uses any analog PSoC block, route sensitive inputs away from switching nodes and power inductors, maintain the recommended grounding topology, and evaluate the final board with the chosen clock source and external components. Programming pads should be mechanically accessible or fixture-compatible for production.
अनुपालन जानकारी
The available product-page extract does not state the required compliance status, so each field remains unknown. Confirm environmental, material, and automotive qualification requirements with the manufacturer before procurement.