Analog Devices

DG406DN+T - 16:1 CMOS Analog Multiplexer | Analog Devices

MPN: DG406DN+T ✓ सक्रिय
100 Ω Rds(on) 28-pin PLCC Package
न्यूनतम ऑर्डर मात्रा: 1 |

DG406DN+T अवलोकन

The Analog Devices DG406DN+T is a 16-channel, single-ended CMOS analog multiplexer with a maximum on-resistance of 100 Ω, housed in a 28-pin PLCC package measuring 11.51 mm by 11.51 mm. It connects one of 16 input channels to a common output according to a 4-bit binary address. The DG406 family is designed for selecting signals in data-acquisition, instrumentation, communication, test, and measurement systems where multiple analog sources must share a limited number of converter or processing inputs.

An analog multiplexer is an analog switch that routes a selected input to a shared output while blocking the unselected channels. In the device hierarchy, the DG406DN+T is an analog multiplexer, a type of analog switch and interface IC. The DG406 family provides 16 single-ended channels, while the related DG407 family provides eight differential channels. This distinction matters because single-ended routing is suitable for unipolar or common-referenced signals, whereas differential multiplexing is preferred for noise-sensitive differential sources.

The manufacturer identifies the DG406 as an improved CMOS analog multiplexer with production status. Its maximum on-resistance is 100 Ω, and the manufacturer also lists guaranteed channel matching of 8 Ω maximum and flatness of 9 Ω maximum over the specified signal range. These specifications support low channel-to-channel variation when a system must measure different analog sources through a common front end. The 4-bit address interface reduces the control logic required to identify the active input.

The DG406 architecture uses CMOS switching elements to provide low power consumption, high switching speed, and consistent signal behavior. Exact switching time, charge injection, off-state leakage, supply current, logic levels, and allowable input-voltage limits are not published in the retrieved product summaries and should be confirmed in the manufacturer datasheet before timing- or precision-sensitive design. Because on-resistance contributes directly to the source impedance seen by downstream converters, system gain and settling calculations should include the selected switch path.

Typical uses include multiplexed data acquisition, automated test equipment, sensor-interface boards, sample-and-hold systems, industrial control modules, and laboratory instruments. The common output can feed an ADC, instrumentation amplifier, measurement front end, or another signal-processing stage. The common-output architecture reduces the number of expensive converter channels, although it also introduces mux on-resistance and switching transients that the downstream acquisition chain must tolerate.

PCB design should keep input and output routing compact, provide a continuous ground reference, and place bypass capacitance near the power pins. Address and enable traces should be controlled away from sensitive analog inputs to minimize capacitive coupling. Because the PLCC footprint is not represented in the available package-diagram library, verify the physical pin orientation and numbering directly against the manufacturer datasheet and the PCB footprint before assembly.

This product page combines the manufacturer’s DG406 architecture information with distributor package and ordering data, a parameter-by-parameter replacement comparison, and practical guidance for layout, signal integrity, and component selection. It is intended to help engineers confirm fit, evaluate channel-error budgets, and choose a pin-compatible replacement without changing the existing 28-pin PLCC layout.

के लिए ड्रॉप-इन विकल्प DG406DN+T — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

इस सीरीज़ के वेरिएंट

समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं DG406DN+T (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Address Inputs, Maximum Channel Matching, Maximum On-Resistance.

Vishay Intertechnology
Address Inputs: 4-bit binary
Maximum Channel Matching: 8 ohm
Maximum On-Resistance: 100 ohm
इसके साथ तुलना करें DG406DN+T →

DG406DN+

✅ ड्रॉप-इन
Vishay Intertechnology
📦 28-pin PLCC (11.51 mm × 11.51 mm)
16:1 single-ended · 16 channels · 4-bit binary · 50 ohm · 100 ohm · 8 ohm · 9 ohm over the specified signal range · 15 pC

कीमत के लिए संपर्क करें

डेटाशीट देखें →

DG406DN-T

✅ ड्रॉप-इन
📦 28-pin PLCC (11.51 mm × 11.51 mm)
Same 16:1, 100 Ω, 28-pin PLCC configuration; no quantified electrical difference is stated between the ordering suffixes

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

DG406DN-T1

✅ ड्रॉप-इन
📦 28-pin PLCC (11.51 mm × 11.51 mm)
Matches the 16:1 configuration, 100 Ω on-resistance class, and 28-pin PLCC package; manufacturer, grade, and sourcing status differ

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

DG406DN+T विशेषताएं

Multiplexer Type 16:1 single-ended analog multiplexer
Number of Channels 16 channels
Address Inputs 4 bits
Maximum On-Resistance 100 Ω
Maximum Channel Matching 8 Ω
Maximum Signal Flatness 9 Ω
Common Output 1 common output
Package Type 28-pin PLCC
Package Dimensions 11.51 mm × 11.51 mm
माउंटिंग प्रकार Surface mount
Semiconductor Technology CMOS
Production Status PRODUCTION

DG406DN+T 11.51 mm × 11.51 mm पिन कॉन्फ़िगरेशन गाइड

DG406DN+T (11.51 mm × 11.51 mm पैकेज) के लिए पिन कॉन्फ़िगरेशन। पिन नंबरिंग, फ़ंक्शन और कनेक्शन आरेख निर्माता डेटाशीट में परिभाषित हैं। सटीक फुटप्रिंट और सोल्डरिंग दिशानिर्देशों के लिए इसे देखें।

DG406DN+T के लिए 11.51 mm × 11.51 mm पैकेज पिनआउट आरेख

इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: DG406DN+T.

देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।

सामान्य अनुप्रयोग

DG406DN+T के लिए उपयुक्त है 6 अनुप्रयोगs: Multiplexed Data Acquisition, Automated Test Equipment, Industrial Sensor Interface, Instrumentation Signal Routing, Battery-Powered Measurement, Communication and Signal Monitoring.

⚡

Multiplexed Data Acquisition

The DG406DN+T is well suited to systems that must scan 16 single-ended sensor or measurement inputs through one common analog channel. Its 4-bit binary address selects the routed input, while the 100 Ω maximum on-resistance adds a defined impedance between the source and the downstream amplifier or ADC. The manufacturer’s guaranteed matching of 8 Ω maximum helps limit channel-to-channel variation when the same gain path is reused. Place the mux near the acquisition front end, use a continuous ground reference, and include switch resistance, settling time, and conversion acquisition time in the complete system error budget.

🏭

Automated Test Equipment

DG406DN+T can route one of 16 test points to a shared measurement amplifier, comparator, or instrument input in an automated test system. This architecture limits the number of repeated high-precision input chains while preserving a common measurement configuration across channels. The 100 Ω maximum on-resistance can affect gain and source loading, so it should be included in the expected signal amplitude at the instrument front end. Guard against address-transition glitches by sequencing the multiplexer before the measurement is acquired, and route the common output away from switching control traces.

🧩

Industrial Sensor Interface

The DG406DN+T allows a compact controller to select among 16 single-ended industrial sensor outputs without requiring sixteen dedicated ADC inputs. It is particularly useful where the sensors share a common reference and the acquisition front end is designed around the mux’s 100 Ω maximum on-resistance. For slowly varying pressure, temperature, or position signals, check leakage and channel matching to ensure that the selected path does not dominate the measurement error. Use a low-impedance buffer when the sensor output impedance is high, and keep sensitive sensor traces short and separated from digital address routing.

📊

Instrumentation Signal Routing

DG406DN+T can select multiple external inputs for a shared precision measurement front end, including reference, calibration, and diagnostic channels. The common-output topology simplifies the analog signal path, while the manufacturer’s 8 Ω maximum matching and 9 Ω maximum flatness specifications help maintain consistency across the specified signal range. For instrumentation systems, account for the selected switch’s contribution to gain and settling behavior and ensure downstream filtering does not create excessive settling time after an address change. A solid reference plane and short analog routes help preserve the intended measurement accuracy.

📱

Battery-Powered Measurement

DG406DN+T is applicable to portable measurement equipment that needs to consolidate several analog inputs before conversion or processing. CMOS construction supports low-power operation, and the 16-to-1 configuration reduces the number of power-hungry converter or amplifier channels that might otherwise be required. The precise quiescent and active supply currents must be taken from the manufacturer data sheet and evaluated across the selected logic state and signal range. For a wearable or portable design, verify startup behavior, supply voltage, leakage into high-impedance sensors, and whether the multiplexed path can settle within the measurement interval.

🌐

Communication and Signal Monitoring

DG406DN+T can monitor or distribute several baseband, control, or diagnostic signals in a communication module. The 4-bit address interface provides straightforward selection logic for a microcontroller, and the common output can feed an ADC or comparator without duplicating analog input stages. Signal integrity depends on keeping the selected paths short, maintaining continuous ground return, and avoiding simultaneous switching noise near sensitive routing. Confirm the mux’s logic thresholds, supply range, switching time, and channel capacitance in the manufacturer data sheet before using it with high-speed signals.

अनुशंसित उत्पादों का सारांश

What is the DG406DN+T used for?
The DG406DN+T is a 16-channel, single-ended CMOS analog multiplexer that routes one selected input to a common output using a 4-bit binary address. According to the Analog Devices DG406 product page, it is a production device with a maximum on-resistance of 100 Ω. It is commonly used in data-acquisition systems, automatic test equipment, instrumentation, sensor interfaces, and industrial control circuits where several analog sources share one downstream measurement channel.
Is DG406DN+T a 16-channel analog multiplexer?
Yes, the DG406DN+T is a 16-channel, single-ended analog multiplexer with one common output. The manufacturer describes the DG406 family as an improved 16-channel CMOS analog multiplexer, and the listed ordering configuration uses a 28-pin PLCC package measuring 11.51 mm by 11.51 mm. A 4-bit binary address determines which one of the 16 inputs is connected to the common output.
What is the on-resistance of the DG406DN+T?
The DG406DN+T has a maximum on-resistance of 100 Ω. According to the Analog Devices DG406 product page, the redesigned family also provides guaranteed channel matching of 8 Ω maximum and flatness of 9 Ω maximum over the specified signal range. These resistance characteristics should be included in the acquisition-chain error budget because the selected switch path contributes to the source impedance seen by the following amplifier or converter.
Where can I download the DG406DN+T datasheet PDF?
The official DG406 datasheet and supporting documentation are available through the Analog Devices DG406 product page at https://www.analog.com/en/products/dg406.html. Use the manufacturer’s Data Sheet resource for the authoritative electrical characteristics, truth table, pin description, package drawings, and ordering information. The distributor listing for DG406DN+T is https://www.digikey.com/en/products/detail/analog-devices-inc-maxim-integrated/DG406DN-T/1303180.
Where can I find the DG406DN+T pinout?
The DG406DN+T pinout is published in the manufacturer’s DG406 data sheet linked from the official Analog Devices product page. The device uses a 28-pin PLCC package with dimensions of 11.51 mm by 11.51 mm. Use the package drawing and pin-description table to assign the four address inputs, enable control, common output, supply pins, and analog input pins, and confirm counter-clockwise numbering against the PCB footprint.
What is the difference between DG406 and DG407?
The DG406 selects one of 16 single-ended inputs to a common output, while the DG407 selects one of eight differential inputs to a common differential output. Both belong to the same improved CMOS analog-multiplexer family and use a 4-bit address interface. Choose the DG406 when sources share a common ground and are single-ended; choose the DG407 when the signal must remain differential through the multiplexing stage.
Can DG406DN-T1 replace DG406DN+T?
DG406DN-T1 is the closest cross-manufacturer candidate identified for a direct replacement review because it is listed as a 16:1, 100 Ω, 28-pin PLCC device matching the target’s main architecture and package. Its manufacturer is Vishay Siliconix, while DG406DN+T is offered under Analog Devices and Maxim Integrated. Production sourcing, grade, marking, lifecycle, and detailed electrical-equivalence requirements should still be confirmed before approving the substitution.
Is DG406DN+ a drop-in replacement for DG406DN+T?
DG406DN+ is a same-family ordering option listed with the same 16:1 configuration, 100 Ω on-resistance class, and 28-pin PLCC package as DG406DN+T. It is therefore a strong footprint candidate, but the ordering suffix may encode grade, temperature, marking, or packaging information. Confirm the complete part-number decoding, temperature range, qualification status, and electrical tables in the manufacturer documentation before treating it as an unconditional substitution.
When should I choose DG406DN+T instead of a cross-package mux?
Choose DG406DN+T when the PCB already uses its 28-pin PLCC land pattern and the design requires 16 single-ended inputs selected by a 4-bit address. Staying with the established footprint avoids connector changes and board rework. Select a different multiplex architecture only when a required channel count, signal range, logic interface, switching speed, qualification level, or package differs enough that a pin-compatible replacement is no longer appropriate.
Is DG406DN+T suitable for high-impedance sensor signals?
DG406DN+T can be considered for sensor multiplexing when the selected channel’s 100 Ω maximum on-resistance is acceptable relative to the sensor and amplifier input impedance. The device also offers guaranteed channel matching of 8 Ω maximum, which helps reduce gain error between channels. For very high-impedance sources, charge injection, leakage, settling time, and input capacitance must be checked in the manufacturer data sheet before finalizing the front-end design.
How should I design the layout around DG406DN+T?
Place the DG406DN+T close to the multiplexed signal sources and the following amplifier or ADC to minimize trace capacitance and resistance. Keep the common output path compact, maintain a continuous ground plane, and decouple the supply pins directly to ground. Route the four address lines and enable control away from sensitive analog inputs, and verify the PLCC orientation and pin-one position against the manufacturer package drawing.
Does the DG406DN+T add much power consumption?
The DG406DN+T uses CMOS switching technology, which is specifically intended to provide low power consumption compared with many older bipolar implementations. The exact supply voltage, quiescent current, and dynamic current are not stated in the retrieved product summaries. Use the manufacturer’s electrical-characteristics table for design calculations, especially in battery-powered or space-constrained measurement systems.
What is the DG406DN+T lifecycle status?
Analog Devices lists the DG406 family as PRODUCTION, indicating that the product remains in production according to the official product page. The DG406DN+T ordering configuration is also represented by current distributor catalog records. Availability and lead time can change, so use the Request a Quote form on this page to confirm the exact suffix, quantity, and current delivery schedule.
Where can I buy DG406DN+T and what is its price?
Use the Request a Quote form on this page to request the current DG406DN+T unit price, stock position, minimum order quantity, and lead time. The exact MPN is identified as a 28-pin PLCC, 16-channel single-ended analog multiplexer with 100 Ω maximum on-resistance. A static price figure is intentionally not stated here because distributor pricing and inventory are time-sensitive and should be confirmed for the requested quantity.
What can replace DG406DN+T?
The leading replacement candidates are DG406DN+, DG406DN-T, and DG406DN-T1 because each is identified as a 16:1, 100 Ω-class analog multiplexer in a 28-pin PLCC package. DG406DN+ and DG406DN-T belong to the Analog Devices or Maxim family, while DG406DN-T1 is listed by Vishay Siliconix. No broader set of qualified alternatives was established, so the complete suffix, grade, marking, lifecycle, and electrical characteristics require review before substitution.
What are the key specifications of DG406DN+T that engineers should know?
The key DG406DN+T specifications are 16 single-ended channels, one common output, 4-bit binary addressing, 100 Ω maximum on-resistance, 8 Ω maximum channel matching, and a 28-pin PLCC package measuring 11.51 mm by 11.51 mm. Analog Devices lists the family as PRODUCTION and identifies it as an improved CMOS analog multiplexer. Supply range, switching time, leakage, charge injection, and temperature limits should be taken from the manufacturer data sheet.

के लिए इंजीनियरिंग संदर्भ डेटा DG406DN+T — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose DG406DN+T when the design requires a 16-channel single-ended analog multiplexer in the 28-pin PLCC footprint and needs the manufacturer’s published 100 Ω maximum on-resistance, 8 Ω maximum channel matching, and 9 Ω maximum flatness. DG406DN+ or DG406DN-T can be preferred when their complete decoded grade and ordering conditions better match procurement or qualification requirements while preserving the same principal electrical architecture. DG406DN-T1 is a cross-manufacturer footprint candidate, but approval should require confirmation of lifecycle, qualification, marking, temperature range, and complete electrical equivalence. Do not select a cross-package multiplexer merely for a lower on-resistance: changing the footprint would require PCB redesign, and a lower resistance alone does not establish equivalent settling behavior, logic compatibility, channel count, or reliability requirements.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद DG406DN+ DG406DN-T DG406DN-T1
Package 28-pin PLCC (11.51 mm × 11.51 mm) 28-pin PLCC (11.51 mm × 11.51 mm) 28-pin PLCC (11.51 mm × 11.51 mm) 28-pin PLCC (11.51 mm × 11.51 mm)
Brand Analog Devices Analog Devices Analog Devices Vishay Intertechnology
Multiplexer Configuration 16:1 single-ended 16:1 single-ended 16:1 single-ended 16:1 single-ended
Number of Channels 16 channels 16 channels 16 channels 16 channels
Maximum On-Resistance 100 Ω 100 Ω 100 Ω 100 Ω

मुख्य विशेषताएँ

  • Guaranteed channel matching for shared-path measurement (बनामDG406DN-T1)
  • Published signal-flatness specification (बनामDG406DN+)
  • Production status documented by the manufacturer (बनामDG406DN-T1)

डिज़ाइन नोट्स

Treat the selected DG406DN+T channel resistance as part of the signal-source impedance. The device has a maximum on-resistance of 100 Ω, which can create a divider with the input impedance of the following amplifier or ADC and can influence charging time at the acquisition node. Calculate the worst-case gain and settling error, and add the ADC sampling aperture and acquisition interval to the switch-transition timing before selecting a conversion rate.

Place the DG406DN+T near the common output node and the downstream front end, while keeping each selected input route short. Maintain a continuous ground plane and route the 4-bit address and enable lines away from analog inputs. Because the available package library does not include a 28-pin PLCC diagram, verify pin-one location, counter-clockwise numbering, pad dimensions, and exposed-component clearance directly from the manufacturer package drawing before releasing the PCB layout.

Do not interpret a shared package and similar on-resistance as proof that every ordering suffix is interchangeable without qualification. Check the decoded temperature range, grade, marking, lead finish, qualification status, and lifecycle for the complete proposed MPN. In particular, DG406DN+, DG406DN-T, and DG406DN-T1 may represent supplier or ordering-code differences even though all three are cataloged as 16:1, 100 Ω devices in the same 28-pin PLCC package.

Use a low-impedance bypass connection between the supply and ground pins, with the capacitor placed as close to the device as practical. Confirm the permitted supply range, input logic thresholds, quiescent current, and dynamic switching current in the manufacturer data sheet. Avoid routing the mux supply through a narrow neck shared with sensitive analog circuitry, because address transitions can create current impulses that disturb reference and supply nodes.

अनुपालन जानकारी

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

No explicit compliance declaration for the exact DG406DN+T ordering code was identified. As an interface IC, the part is not an automotive-qualified product unless a separate qualified ordering option is specifically documented.

डेटा सत्यापन तिथि: 2026-11-16 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

DG406DN+T datasheet DG406DN+T pinout DG406DN+T datasheet pdf DG406DN+T equivalent DG406DN+T replacement DG406DN+T cross reference DG406DN+T 28 PLCC DG406DN+T price DG406DN+T stock Analog Devices DG406DN+T DG406DN+T vs DG406DN-T1 DG406DN+T application circuit DG406 16 channel multiplexer DG406DN+T PLCC footprint

संबंधित कंपोनेंट्स और शब्द

Analog Devices DG406DN+T DG406DN+ DG406DN-T DG406DN-T1 Vishay Intertechnology Maxim Integrated DG406 DG407 analog multiplexer analog switch interface IC CMOS analog multiplexer 16:1 multiplexer single-ended analog switch 4-bit binary address on-resistance channel matching signal flatness PLCC-28 surface mount data acquisition automated test equipment instrumentation industrial sensor interface
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें