DG406DN+T - 16:1 CMOS Analog Multiplexer | Analog Devices
部品番号: DG406DN+T ✓ 生産中DG406DN+T 概要
An analog multiplexer is an analog switch that routes a selected input to a shared output while blocking the unselected channels. In the device hierarchy, the DG406DN+T is an analog multiplexer, a type of analog switch and interface IC. The DG406 family provides 16 single-ended channels, while the related DG407 family provides eight differential channels. This distinction matters because single-ended routing is suitable for unipolar or common-referenced signals, whereas differential multiplexing is preferred for noise-sensitive differential sources.
The manufacturer identifies the DG406 as an improved CMOS analog multiplexer with production status. Its maximum on-resistance is 100 Ω, and the manufacturer also lists guaranteed channel matching of 8 Ω maximum and flatness of 9 Ω maximum over the specified signal range. These specifications support low channel-to-channel variation when a system must measure different analog sources through a common front end. The 4-bit address interface reduces the control logic required to identify the active input.
The DG406 architecture uses CMOS switching elements to provide low power consumption, high switching speed, and consistent signal behavior. Exact switching time, charge injection, off-state leakage, supply current, logic levels, and allowable input-voltage limits are not published in the retrieved product summaries and should be confirmed in the manufacturer datasheet before timing- or precision-sensitive design. Because on-resistance contributes directly to the source impedance seen by downstream converters, system gain and settling calculations should include the selected switch path.
Typical uses include multiplexed data acquisition, automated test equipment, sensor-interface boards, sample-and-hold systems, industrial control modules, and laboratory instruments. The common output can feed an ADC, instrumentation amplifier, measurement front end, or another signal-processing stage. The common-output architecture reduces the number of expensive converter channels, although it also introduces mux on-resistance and switching transients that the downstream acquisition chain must tolerate.
PCB design should keep input and output routing compact, provide a continuous ground reference, and place bypass capacitance near the power pins. Address and enable traces should be controlled away from sensitive analog inputs to minimize capacitive coupling. Because the PLCC footprint is not represented in the available package-diagram library, verify the physical pin orientation and numbering directly against the manufacturer datasheet and the PCB footprint before assembly.
This product page combines the manufacturer’s DG406 architecture information with distributor package and ordering data, a parameter-by-parameter replacement comparison, and practical guidance for layout, signal integrity, and component selection. It is intended to help engineers confirm fit, evaluate channel-error budgets, and choose a pin-compatible replacement without changing the existing 28-pin PLCC layout.
ドロップイン代替品: DG406DN+T — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: DG406DN+T (同一形状・フットプリント) — 相違点: Address Inputs, Maximum Channel Matching, Maximum On-Resistance.
DG406DN+
✅ ドロップイン価格はお問い合わせください
データシートを見る →DG406DN-T
✅ ドロップイン📋 参考代替品(カタログ未掲載)
DG406DN-T1
✅ ドロップイン📋 参考代替品(カタログ未掲載)
DG406DN+T 仕様
| Multiplexer Type | 16:1 single-ended analog multiplexer |
| Number of Channels | 16 channels |
| Address Inputs | 4 bits |
| Maximum On-Resistance | 100 Ω |
| Maximum Channel Matching | 8 Ω |
| Maximum Signal Flatness | 9 Ω |
| Common Output | 1 common output |
| Package Type | 28-pin PLCC |
| Package Dimensions | 11.51 mm × 11.51 mm |
| 実装タイプ | Surface mount |
| Semiconductor Technology | CMOS |
| Production Status | PRODUCTION |
DG406DN+T 11.51 mm × 11.51 mm ピン配置ガイド
DG406DN+T (11.51 mm × 11.51 mm パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: DG406DN+T.
詳細は データシート をご参照ください。
主な用途
DG406DN+T の用途: 6 件s: Multiplexed Data Acquisition, Automated Test Equipment, Industrial Sensor Interface, Instrumentation Signal Routing, Battery-Powered Measurement, Communication and Signal Monitoring.
Multiplexed Data Acquisition
The DG406DN+T is well suited to systems that must scan 16 single-ended sensor or measurement inputs through one common analog channel. Its 4-bit binary address selects the routed input, while the 100 Ω maximum on-resistance adds a defined impedance between the source and the downstream amplifier or ADC. The manufacturer’s guaranteed matching of 8 Ω maximum helps limit channel-to-channel variation when the same gain path is reused. Place the mux near the acquisition front end, use a continuous ground reference, and include switch resistance, settling time, and conversion acquisition time in the complete system error budget.
おすすめ
Automated Test Equipment
DG406DN+T can route one of 16 test points to a shared measurement amplifier, comparator, or instrument input in an automated test system. This architecture limits the number of repeated high-precision input chains while preserving a common measurement configuration across channels. The 100 Ω maximum on-resistance can affect gain and source loading, so it should be included in the expected signal amplitude at the instrument front end. Guard against address-transition glitches by sequencing the multiplexer before the measurement is acquired, and route the common output away from switching control traces.
おすすめ
Industrial Sensor Interface
The DG406DN+T allows a compact controller to select among 16 single-ended industrial sensor outputs without requiring sixteen dedicated ADC inputs. It is particularly useful where the sensors share a common reference and the acquisition front end is designed around the mux’s 100 Ω maximum on-resistance. For slowly varying pressure, temperature, or position signals, check leakage and channel matching to ensure that the selected path does not dominate the measurement error. Use a low-impedance buffer when the sensor output impedance is high, and keep sensitive sensor traces short and separated from digital address routing.
おすすめ
Instrumentation Signal Routing
DG406DN+T can select multiple external inputs for a shared precision measurement front end, including reference, calibration, and diagnostic channels. The common-output topology simplifies the analog signal path, while the manufacturer’s 8 Ω maximum matching and 9 Ω maximum flatness specifications help maintain consistency across the specified signal range. For instrumentation systems, account for the selected switch’s contribution to gain and settling behavior and ensure downstream filtering does not create excessive settling time after an address change. A solid reference plane and short analog routes help preserve the intended measurement accuracy.
おすすめ
Battery-Powered Measurement
DG406DN+T is applicable to portable measurement equipment that needs to consolidate several analog inputs before conversion or processing. CMOS construction supports low-power operation, and the 16-to-1 configuration reduces the number of power-hungry converter or amplifier channels that might otherwise be required. The precise quiescent and active supply currents must be taken from the manufacturer data sheet and evaluated across the selected logic state and signal range. For a wearable or portable design, verify startup behavior, supply voltage, leakage into high-impedance sensors, and whether the multiplexed path can settle within the measurement interval.
おすすめ
Communication and Signal Monitoring
DG406DN+T can monitor or distribute several baseband, control, or diagnostic signals in a communication module. The 4-bit address interface provides straightforward selection logic for a microcontroller, and the common output can feed an ADC or comparator without duplicating analog input stages. Signal integrity depends on keeping the selected paths short, maintaining continuous ground return, and avoiding simultaneous switching noise near sensitive routing. Confirm the mux’s logic thresholds, supply range, switching time, and channel capacitance in the manufacturer data sheet before using it with high-speed signals.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: DG406DN+T — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | DG406DN+ | DG406DN-T | DG406DN-T1 |
|---|---|---|---|---|
| Package | 28-pin PLCC (11.51 mm × 11.51 mm) | 28-pin PLCC (11.51 mm × 11.51 mm) | 28-pin PLCC (11.51 mm × 11.51 mm) | 28-pin PLCC (11.51 mm × 11.51 mm) |
| Brand | Analog Devices | Analog Devices | Analog Devices | Vishay Intertechnology |
| Multiplexer Configuration | 16:1 single-ended | 16:1 single-ended | 16:1 single-ended | 16:1 single-ended |
| Number of Channels | 16 channels | 16 channels | 16 channels | 16 channels |
| Maximum On-Resistance | 100 Ω | 100 Ω | 100 Ω | 100 Ω |
主な差別化要因
- Guaranteed channel matching for shared-path measurement (vs DG406DN-T1)
- Published signal-flatness specification (vs DG406DN+)
- Production status documented by the manufacturer (vs DG406DN-T1)
設計ノート
Treat the selected DG406DN+T channel resistance as part of the signal-source impedance. The device has a maximum on-resistance of 100 Ω, which can create a divider with the input impedance of the following amplifier or ADC and can influence charging time at the acquisition node. Calculate the worst-case gain and settling error, and add the ADC sampling aperture and acquisition interval to the switch-transition timing before selecting a conversion rate.
Place the DG406DN+T near the common output node and the downstream front end, while keeping each selected input route short. Maintain a continuous ground plane and route the 4-bit address and enable lines away from analog inputs. Because the available package library does not include a 28-pin PLCC diagram, verify pin-one location, counter-clockwise numbering, pad dimensions, and exposed-component clearance directly from the manufacturer package drawing before releasing the PCB layout.
Do not interpret a shared package and similar on-resistance as proof that every ordering suffix is interchangeable without qualification. Check the decoded temperature range, grade, marking, lead finish, qualification status, and lifecycle for the complete proposed MPN. In particular, DG406DN+, DG406DN-T, and DG406DN-T1 may represent supplier or ordering-code differences even though all three are cataloged as 16:1, 100 Ω devices in the same 28-pin PLCC package.
Use a low-impedance bypass connection between the supply and ground pins, with the capacitor placed as close to the device as practical. Confirm the permitted supply range, input logic thresholds, quiescent current, and dynamic switching current in the manufacturer data sheet. Avoid routing the mux supply through a narrow neck shared with sensitive analog circuitry, because address transitions can create current impulses that disturb reference and supply nodes.
コンプライアンス情報
No explicit compliance declaration for the exact DG406DN+T ordering code was identified. As an interface IC, the part is not an automotive-qualified product unless a separate qualified ordering option is specifically documented.