DP83847ALQA56AX - 10/100 Ethernet PHY | Texas Instruments
MPN: DP83847ALQA56AX ✓ सक्रियDP83847ALQA56AX अवलोकन
An Ethernet PHY, or physical-layer transceiver, is the circuit that converts between digital Ethernet data and analog signals carried over twisted-pair wiring. It belongs to the network-interface hierarchy: Ethernet PHY, network interface controller, interface IC, and semiconductor. The DP83847 also supports the Parallel Detection function defined by the IEEE 802.3u specification. Parallel Detection allows both the 10 Mb/s and 100 Mb/s receivers to monitor the receive signal and report link status to the Auto-Negotiation function.
The principal benefits of this transceiver include support for both 10 Mb/s and 100 Mb/s links, 5-V-tolerant digital I/O operation, integrated PMD sublayers, and support for Category 3 or Category 5 cabling. The 56-WQFN package is intended for compact surface-mount designs, while the external transformer provides the physical isolation and impedance-matching interface between the PHY and the network cable. The exposed-pad construction also permits heat to spread through the PCB copper area.
The DP83847 family is suited to embedded systems, industrial Ethernet equipment, communications equipment, network-interface controllers, and other products that require a copper twisted-pair Ethernet port. Its parallel digital interface connects the PHY to a host processor or network controller, while the analog side connects through the customary external magnetics and center-tapped transmit/receive circuitry. The manufacturer describes the device as a full-feature single Physical Layer device with integrated PMD sublayers.
For a new design, the exact variant ordering information, exposed-pad layout, absolute maximum ratings, register map, and recommended application circuit should be taken directly from the manufacturer datasheet. The DP83847ALQA56AX product designation must also be checked against the required package suffix, temperature grade, lead-finish option, and tape-and-reel ordering code before release to production.
This page organizes the confirmed manufacturer and distributor information into a design-focused product record. It highlights the DP83847ALQA56AX as a 10/100-Mbps, 3.3-V Ethernet PHY in a 56-WQFN package, documents practical implementation considerations, identifies the directly supported ordering variant, and explains where a design must consult the DP83847 datasheet for pin-level and electrical details.
के लिए ड्रॉप-इन विकल्प DP83847ALQA56AX — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
DP83847ALQA56AX/NOPB
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
DP83847ALQA56AX
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →DP83847ALQA56AX विशेषताएं
| Product Type | Ethernet physical-layer transceiver |
| Ethernet Data Rate | 10 Mb/s and 100 Mb/s |
| Supported Protocols | 10BASE-T and 100BASE-TX |
| Supported Cable | Category 3 and Category 5 unshielded twisted pair |
| Transceiver Channels | 1 channel |
| सप्लाई वोल्टेज | 3.0 V to 3.6 V |
| Digital I/O Tolerance | 5 V tolerant |
| Integrated PMD Sublayers | Yes |
| Parallel Detection | Supported as defined in IEEE 802.3u |
| External Transformer | Required for twisted-pair media interface |
| पैकेज | 56-WQFN, 9 mm x 9 mm |
| माउंटिंग प्रकार | Surface mount |
| पिन काउंट | 56 pins |
| Exposed Thermal Pad | Present |
| Ordering Variant | DP83847ALQA56AX; DP83847ALQA56AX/NOPB also listed |
| Manufacturer Product Page | Texas Instruments DP83847 product family |
DP83847ALQA56AX 56-wqfn, 9 mm x 9 mm पिन कॉन्फ़िगरेशन गाइड
DP83847ALQA56AX (56-wqfn, 9 mm x 9 mm पैकेज) के लिए पिन कॉन्फ़िगरेशन। पिन नंबरिंग, फ़ंक्शन और कनेक्शन आरेख निर्माता डेटाशीट में परिभाषित हैं। सटीक फुटप्रिंट और सोल्डरिंग दिशानिर्देशों के लिए इसे देखें।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: DP83847ALQA56AX.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
DP83847ALQA56AX के लिए उपयुक्त है 6 अनुप्रयोगs: Industrial Ethernet Control Equipment, Embedded Network Interface, Communications Gateway, Network Interface Controller, Building Network Endpoint, Test and Measurement Instrument.
Industrial Ethernet Control Equipment
The DP83847ALQA56AX fits industrial Ethernet controllers, remote I/O products, and programmable automation equipment that require 10BASE-T or 100BASE-TX connectivity. Its 3.0 V to 3.6 V supply and 5-V-tolerant I/Os support integration with a 3.3-V host interface, while the 56-WQFN package preserves a compact land pattern. The external transformer provides the cable-side isolation stage. Confirm the exact temperature grade for the installation environment and use the manufacturer reference circuit to control magnetics layout, grounding, and high-frequency return paths.
अनुशंसित
Embedded Network Interface
DP83847ALQA56AX is appropriate for embedded Linux, industrial controller, and communications gateways that expose a copper Ethernet port through a host processor or dedicated network controller. The transceiver handles the physical 10/100-Mbps layer, including integrated PMD functions, while the upper-layer controller manages framing and protocol services. Operating from 3.0 V to 3.6 V allows it to share a conventional 3.3-V power architecture, and the 5-V-tolerant I/Os simplify interfacing with compatible digital systems. Preserve the manufacturer-recommended reset, clock, decoupling, and transformer arrangements.
अनुशंसित
Communications Gateway
A communications gateway can use the DP83847ALQA56AX to add a 10/100-Mbps twisted-pair Ethernet port to equipment that already has a host-side parallel interface. Supporting both 10BASE-T and 100BASE-TX allows the PHY to negotiate operation over Category 3 or Category 5 cabling, which is useful for long-lived industrial and building-network installations. The external transformer maintains the required separation between the board and copper medium. Validate cable reach, auto-negotiation behavior, and system timing against the final magnetics and firmware configuration.
अनुशंसित
Network Interface Controller
The DP83847ALQA56AX can serve as the copper physical layer beside a digital MAC or embedded network controller. It translates the MAC-side digital signaling into 10BASE-T or 100BASE-TX physical signaling and reports the physical link through the interface described by the manufacturer documentation. This arrangement is suitable for compact single-port network adapters where a 56-WQFN footprint is practical. Pay particular attention to signal timing, shared reset behavior, pull components, and the exposed-pad thermal path in the PCB design.
अनुशंसित
Building Network Endpoint
DP83847ALQA56AX is suitable for building-network endpoints such as access terminals, room controllers, and commercial communications equipment that use 10/100-Mbps copper Ethernet. The device supports Category 3 and Category 5 unshielded twisted-pair media, helping designers accommodate existing horizontal wiring while retaining a conventional 3.3-V power rail. The external-transformer architecture must be implemented carefully to preserve galvanic isolation and EMC behavior. Verify the device's exact environmental limits and production ordering suffix before installation.
अनुशंसित
Test and Measurement Instrument
The DP83847ALQA56AX can provide network connectivity in test and measurement equipment that requires a single copper Ethernet management port. Its dual support for 10 Mb/s and 100 Mb/s operation allows the instrument to connect to older 10 Mb/s infrastructure as well as faster 100 Mb/s networks, subject to the host driver's supported link modes. The small 56-WQFN package helps preserve instrument-panel space, while 5-V-tolerant I/Os assist host integration. Keep analog routing compact and follow the transformer reference layout.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा DP83847ALQA56AX — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | DP83847ALQA56AX/NOPB | DP83847ALQA56AX |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 56-WQFN (9x9) | 56-WQFN (9x9) | 56-WQFN (9x9) |
| Product Function | 10/100 Ethernet PHY transceiver | 10/100 Ethernet PHY transceiver | 10/100 Ethernet PHY transceiver |
| Supported Data Rates | 10 Mb/s and 100 Mb/s | 10 Mb/s and 100 Mb/s | 10 Mb/s and 100 Mb/s |
| Supported Protocols | 10BASE-T and 100BASE-TX | 10BASE-T and 100BASE-TX | 10BASE-T and 100BASE-TX |
| Supply Voltage | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V |
| Digital I/O Tolerance | 5 V tolerant | 5 V tolerant | 5 V tolerant |
| External Transformer | Required | Required | Required |
| Parallel Detection | Supported per IEEE 802.3u | Supported per IEEE 802.3u | Supported per IEEE 802.3u |
| Ordering Suffix | DP83847ALQA56AX | /NOPB suffix; exact suffix attribute is not quantified | Target ordering designation |
मुख्य विशेषताएँ
- Same-family ordering option preserves the physical footprint (बनामDP83847ALQA56AX/NOPB)
- Supports both legacy and fast copper Ethernet rates (बनामLAN8720A)
- Supports copper cabling and an external transformer interface (बनामLAN8720A)
डिज़ाइन नोट्स
Follow the manufacturer reference circuit for the external transformer, center-tap capacitors, and PHY-side connections. Keep the analog network compact and route differential and power-supply paths away from exposed-pad and digital return currents. The DP83847 supports 10BASE-T and 100BASE-TX, so uncontrolled impedance discontinuities can degrade return loss, common-mode balance, or link-margin performance even when the digital interface operates correctly.
The 56-WQFN device includes an exposed thermal pad that should be connected to the PCB ground plane using the manufacturer-recommended via pattern. Estimated thermal performance depends on the actual copper area, via count, board stack-up, ambient temperature, and adjacent heat sources; these inputs are not stated here. Avoid placing thermally sensitive analog or magnetics components directly beneath an unventilated exposed-pad region.
Decouple each applicable supply pin locally and follow the manufacturer’s power-supply sequencing and reset requirements. The confirmed core supply range is 3.0 V to 3.6 V, while the digital I/O interface is described as 5-V tolerant. Do not use the 5-V-tolerant I/O statement to justify applying 5 V to the core supply. Verify voltage thresholds and absolute maximum ratings in the datasheet before connecting host signals.
Do not treat a modern 10/100 Ethernet PHY as a drop-in substitute unless its package, exposed pad, pinout, transformer interface, power sequence, and host-interface timing all match. The cross-reference listing specifically identifies LAN8720A as not being a true drop-in replacement for DP83847ALQA56AX because of pinout, sequencing, and interface differences. For the identified DP83847 suffix option, verify the ordering table before replacing the target MPN.
अनुपालन जानकारी
The available product information identifies a /NOPB ordering option but does not state the exact suffix-specific environmental or material-compliance declarations. Verify the current declarations for the selected ordering code with Texas Instruments.