Texas Instruments

DS90LV048ATMTC - 400 Mbps Quad LVDS Receiver | Texas Instruments

MPN: DS90LV048ATMTC ✓ सक्रिय
3.3 V Vdss 16-TSSOP Package
न्यूनतम ऑर्डर मात्रा: 1 |

DS90LV048ATMTC अवलोकन

The Texas Instruments DS90LV048ATMTC is a 3 V quad CMOS differential line receiver supporting data rates above 400 Mbps, equivalent to 200 MHz, in a 16-pin TSSOP package. It accepts four Low Voltage Differential Signaling inputs and provides CMOS-compatible outputs for high-speed point-to-point interfaces. The receiver architecture emphasizes ultra-low power dissipation and accommodates balanced LVDS signaling.

An LVDS receiver is a differential interface circuit that extracts a digital signal from two complementary low-voltage conductors. LVDS belongs to the high-speed differential-signaling family and sits below general-purpose interface ICs in the semiconductor hierarchy: receiver IC -> differential line receiver -> interface IC -> semiconductor. Its differential architecture improves noise immunity by detecting the voltage difference between a pair of lines rather than relying on a single conductor referenced only to ground.

The DS90LV048A family provides four independent receiver channels, a 400 Mbps signaling rate, operation from a 3.3 V supply, and common enable control for the output stage. The flow-through signal path supports straightforward point-to-point links between a compatible LVDS transmitter and receiving logic. CMOS outputs allow the device to interface with digital systems operating from the same 3.3 V rail.

Electrical operation depends on the differential input voltage and receiver threshold rather than single-ended logic levels. The LVDS input arrangement improves signal-to-noise ratio and reduces sensitivity to common-mode noise when the transmitter, receiver, connectors, and cable form a controlled impedance environment. The manufacturer identifies the DS90LV048A as a low-power alternative to high-power PECL and ECL devices in suitable point-to-point applications.

Typical uses include industrial control links, instrumentation, video or imaging backplanes, test equipment, and communications equipment requiring several high-speed LVDS channels. The quad-channel configuration reduces package count compared with discrete single-channel receivers. In point-to-point links, the DS90LV048ATMTC can be paired with an LVDS line driver such as the DS90LV047A while preserving the low-voltage differential signaling architecture.

PCB implementation should use a compact, controlled-impedance routing scheme and place termination close to the receiver when the selected link topology requires it. Differential pair spacing and length matching should follow the characteristics of the LVDS transmitter and interconnect. Supply and ground distribution should be decoupled close to the device because simultaneous switching across four fast receiver channels can create transient current in the power rails.

This page combines the manufacturer's receiver specifications, ordering details, practical interface guidance, and qualified same-footprint references. It also distinguishes confirmed orderable variants from broader functional alternatives, helping engineers assess replacement compatibility before changing an LVDS link or PCB assembly.

के लिए ड्रॉप-इन विकल्प DS90LV048ATMTC — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

DS90LV048ATMTC/NOPB

✅ ड्रॉप-इन
📦 16-TSSOP
Same 400 Mbps quad-LVDS receiver function and 16-TSSOP footprint; ordering suffix differs with 0% identified change to key receiver ratings.

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

DS90LV048ATMTCX/NOPB

✅ ड्रॉप-इन
📦 16-TSSOP
Same 400 Mbps quad-LVDS receiver function and 16-TSSOP footprint; ordering and shipping form differ with 0% identified change to key receiver ratings.

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

DS90LV048ATMTC विशेषताएं

Receiver Type Quad CMOS flow-through differential line receiver
Number of Receiver Channels 4 channels
Number of Transmitter Channels 0 channels
Signaling Standard LVDS
Maximum Data Rate 400 Mbps
Equivalent Data Rate 200 MHz
सप्लाई वोल्टेज 3.3 V
Output Interface CMOS
Input Signal LVDS differential input
Output Enable Control Common enable and enable-bar control
पैकेज 16-TSSOP
Package Width 4.40 mm
Package Body Length 0.173 inch
माउंटिंग प्रकार Surface mount
ऑपरेटिंग तापमान रेंज -40 °C to +85 °C

DS90LV048ATMTC 0.173 inch पिन कॉन्फ़िगरेशन गाइड

DS90LV048ATMTC (0.173 inch पैकेज) के लिए पिन कॉन्फ़िगरेशन। पिन नंबरिंग, फ़ंक्शन और कनेक्शन आरेख निर्माता डेटाशीट में परिभाषित हैं। सटीक फुटप्रिंट और सोल्डरिंग दिशानिर्देशों के लिए इसे देखें।

DS90LV048ATMTC के लिए 0.173 inch पैकेज पिनआउट आरेख

इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: DS90LV048ATMTC.

देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।

सामान्य अनुप्रयोग

DS90LV048ATMTC के लिए उपयुक्त है 6 अनुप्रयोगs: Industrial Point-to-Point Control Links, Video and Imaging Data Backplanes, Test and Measurement Instrumentation, Communications Equipment, Imaging Sensor Interfaces, Automotive and Robust Embedded Links.

🏭

Industrial Point-to-Point Control Links

The DS90LV048ATMTC fits industrial control links that require four differential receive channels at rates above 400 Mbps. Each channel converts an LVDS pair into a CMOS output, allowing a controller or FPGA to receive data from remote high-speed nodes while rejecting common-mode noise. The four-channel integration reduces package count and board area compared with four discrete receiver packages. Designers should preserve controlled-impedance differential routing, provide the documented termination network, and decouple the 3.3 V supply close to the device. The -40 °C to +85 °C operating range supports industrial equipment where internal temperatures exceed ordinary consumer conditions.

📺

Video and Imaging Data Backplanes

The DS90LV048ATMTC is appropriate for parallel video or imaging data paths that use four LVDS pairs between circuit boards or modules. Its support for rates above 400 Mbps and CMOS outputs makes it suitable for receiving serialized high-speed data from a transmitter, although the device does not itself perform protocol conversion, color processing, or packet decoding. Four channels can carry related pixel, synchronization, or control streams without requiring four separate receiver packages. Keep each differential pair continuous over a ground reference, minimize stub branches, and verify connector and cable impedance before production release.

🔧

Test and Measurement Instrumentation

The DS90LV048ATMTC can receive four high-speed differential channels in laboratory instruments, automated test equipment, and data-acquisition systems. Its 400 Mbps-class operation supports fast transfer of measurement results, trigger signals, or status information between circuit sections while CMOS outputs connect directly to suitable control logic. The quad architecture helps instruments consolidate several links behind one receiver package. The principal design considerations are clean supply distribution, return-path continuity, and compliance with the LVDS voltage thresholds of the selected transmitter. Validate timing margins across temperature because propagation delay and receiver performance must remain acceptable for the complete measurement sequence.

🌐

Communications Equipment

The DS90LV048ATMTC is useful in communications equipment requiring multiple high-speed LVDS receive ports. Four differential channels can carry clock, data, status, and supervisory signals between modules, with each input providing a CMOS output for downstream digital circuitry. This is particularly helpful in compact backplanes where connector density is constrained and reducing receiver package count improves routing flexibility. Designers must maintain differential impedance through the entire path and account for connector loss, cable length, and the transmitter's recommended termination. The receiver should be placed near the connector when channel loss or skew is significant, with supply bypassing arranged to avoid shared high-frequency current paths.

🎥

Imaging Sensor Interfaces

The DS90LV048ATMTC can serve as the receiving element in imaging modules that transfer several high-speed differential streams from a sensor or transmitter board. Its four receivers support data above 400 Mbps per channel, while CMOS outputs provide a convenient interface to an FPGA or other digital controller. Multiple parallel channels can carry pixel data, synchronization information, or configuration status when the remote transmitter implements the corresponding LVDS signaling. The receiver itself does not deserialize or format the image, so synchronization and protocol handling remain the responsibility of the receiving controller. PCB layout should preserve return-current continuity beneath every differential pair and provide local supply decoupling.

🚗

Automotive and Robust Embedded Links

The DS90LV048ATMTC can be considered for robust embedded signal links where four LVDS channels are needed across a compact board or module. Its -40 °C to +85 °C range and differential signaling provide useful noise immunity for data transferred between circuit sections, converters, sensors, or communication modules. The receiver is not identified as an AEC-Q100-qualified automotive part, so qualification requirements must be checked separately rather than inferred from the industrial temperature range. Keep the supply and return planes continuous, place bypass capacitors at the device, and verify the complete channel against the driver's threshold, timing, and termination requirements.

अनुशंसित उत्पादों का सारांश

DS90LV047A Quad LVDS line driver for point-to-point receiver links उपयोग में: Industrial Point-to-Point Control Links, Video and Imaging Data Backplanes, Test and Measurement Instrumentation, Communications Equipment, Imaging Sensor Interfaces, Automotive and Robust Embedded Links DS90LV048A Receiver family used for multi-channel LVDS reception उपयोग में: Industrial Point-to-Point Control Links, Video and Imaging Data Backplanes, Test and Measurement Instrumentation, Communications Equipment, Imaging Sensor Interfaces, Automotive and Robust Embedded Links
What is the DS90LV048ATMTC?
The DS90LV048ATMTC is a 3.3 V quad CMOS differential line receiver designed for Low Voltage Differential Signaling links operating above 400 Mbps. According to the Texas Instruments DS90LV048A datasheet, the device contains four LVDS receiver channels in a 16-pin TSSOP package and provides CMOS outputs for connection to compatible digital logic.
What is the maximum data rate of DS90LV048ATMTC?
The DS90LV048ATMTC supports data rates in excess of 400 Mbps, corresponding to 200 MHz. According to the Texas Instruments DS90LV048A datasheet, the receiver uses a flow-through differential architecture intended for high-speed point-to-point LVDS interfaces while emphasizing ultra-low power dissipation.
How many LVDS receiver channels does DS90LV048ATMTC have?
The DS90LV048ATMTC has four independent LVDS receiver channels and no integrated transmitter channels. According to the Texas Instruments product description, each receiver converts a differential LVDS input into a CMOS output, allowing one compact package to handle four high-speed links.
What is the DS90LV048ATMTC package?
The DS90LV048ATMTC is packaged in a 16-pin TSSOP with a stated width of 4.40 mm and body length of 0.173 inch. The Texas Instruments listing identifies surface-mount construction, and the manufacturer datasheet should be consulted for the land pattern, pin numbering, maximum package dimensions, and exposed thermal information.
Where can I download the DS90LV048ATMTC datasheet PDF?
The official DS90LV048ATMTC datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/ds90lv048a.pdf. It is the primary document for electrical characteristics, receiver thresholds, propagation timing, enable behavior, recommended operating conditions, package drawings, and application guidance.
Where can I find the DS90LV048ATMTC pinout?
The DS90LV048ATMTC pinout is shown in the pin-configuration section of the Texas Instruments DS90LV048A datasheet. The part uses a 16-pin TSSOP footprint, and the manufacturer drawing identifies each differential input, CMOS output, supply, ground, and enable connection. Use that drawing when assigning PCB tracks and connector routing.
Can DS90LV047A be paired with DS90LV048ATMTC?
Yes, the Texas Instruments DS90LV047A is the companion quad LVDS driver cited for the DS90LV048A family. The receiver accepts the differential outputs from that driver and converts them into CMOS signals. Compatibility still depends on matching the supply voltage, data rate, termination scheme, enable sequencing, and connector pin assignment used on the board.
What is the difference between DS90LV048ATMTC and DS90LV048ATMTC/NOPB?
The DS90LV048ATMTC and DS90LV048ATMTC/NOPB are identified by Texas Instruments as equivalent orderable versions of the 16-TSSOP quad LVDS receiver, with the same 400 Mbps class and CMOS receiver function. The distinguishing ordering suffix relates to the specific ordering configuration; confirm the exact package dimensions, temperature grade, shipping form, and marking against the manufacturer ordering information.
Is DS90LV048ATMTC a drop-in replacement for DS90LV048ATMTC/NOPB?
The DS90LV048ATMTC can serve as a drop-in ordering choice for the DS90LV048ATMTC/NOPB when the original board uses the same 16-pin TSSOP receiver footprint and electrical configuration. The manufacturer family listing identifies both as equivalent parts. A production substitution should still be checked against exact ordering codes, temperature grade, shipping form, and RoHS documentation.
What can replace the DS90LV048ATMTC?
The clearest documented replacements are Texas Instruments DS90LV048ATMTC/NOPB and DS90LV048ATMTCX/NOPB, which use the same 16-TSSOP receiver family and retain the 400 Mbps LVDS receiver function. No verified cross-manufacturer drop-in candidate was identified for the exact MPN, so a different supplier should not be assumed compatible without a documented pin-for-pin and electrical comparison.
When should I choose DS90LV048ATMTC over a single-channel LVDS receiver?
Choose DS90LV048ATMTC when the design requires four high-speed LVDS receive links in a compact package. Its four-channel integration reduces the number of receiver packages and provides common output-enable control. A single-channel receiver may be preferable only when the system needs one link, has severe space constraints elsewhere, or requires a different electrical or protocol variant.
Is DS90LV048ATMTC suitable for industrial and instrumentation links?
The DS90LV048ATMTC is suitable for many industrial and instrumentation links because it combines four 400 Mbps-class LVDS receivers with CMOS outputs and an operating range of -40 °C to +85 °C. The interface still requires suitable differential routing, power-decoupling design, connector discipline, and compatible transmitters for reliable results in electrically noisy environments.
Where can I buy DS90LV048ATMTC and what is its price?
Use the Request a Quote form on this page to request DS90LV048ATMTC pricing, stock confirmation, minimum order quantity, and current lead time. Quote-based confirmation is appropriate because availability and commercial terms can change independently of the device specifications. The orderable MPN, 16-TSSOP package, and required quantity should be stated in the request.
Is DS90LV048ATMTC currently in stock?
Current DS90LV048ATMTC stock should be confirmed through the Request a Quote form on this page. The listing identifies the part as a standard Texas Instruments catalog device, but inventory quantity and delivery timing can vary by package form and order quantity. Include the exact MPN, target quantity, shipment destination, and required date in the request.
What are the key specifications of DS90LV048ATMTC that engineers should know?
The key DS90LV048ATMTC specifications are four LVDS receive channels, support for data rates above 400 Mbps, 3.3 V operation, CMOS outputs, and a 16-pin TSSOP package. According to the Texas Instruments DS90LV048A datasheet, the device is intended for high-speed point-to-point LVDS links and offers a low-power alternative to high-power PECL and ECL interfaces.

के लिए इंजीनियरिंग संदर्भ डेटा DS90LV048ATMTC — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose DS90LV048ATMTC when a board needs four 400 Mbps-class LVDS receive channels, 3.3 V CMOS outputs, and a 16-TSSOP footprint. It is particularly suitable for compact industrial, instrumentation, imaging, and communications links where reducing receiver package count is valuable. The DS90LV048ATMTC/NOPB is the closest documented ordering alternative and may be selected when its exact qualification, marking, or shipping configuration matches the procurement requirement. DS90LV048ATMTCX/NOPB provides another same-family ordering route with the same identified receiver ratings and package. Do not choose either alternative merely because it is described as equivalent; verify the exact suffix and manufacturing data before releasing production quantities. No verified cross-manufacturer drop-in equivalent was established for this exact MPN, so engineers should avoid assuming that another LVDS receiver is pin-compatible without checking every differential input, output, enable, supply, ground, and exposed-pad connection.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद DS90LV048ATMTC/NOPB DS90LV048ATMTCX/NOPB
Package 16-TSSOP 16-TSSOP 16-TSSOP
Brand Texas Instruments Texas Instruments Texas Instruments
Receiver Function Quad CMOS flow-through differential line receiver Quad CMOS flow-through differential line receiver Quad CMOS flow-through differential line receiver
Number of Receiver Channels 4 channels 4 channels 4 channels
Signaling Rate Above 400 Mbps 400 Mbps 400 Mbps
Equivalent Clock Rate 200 MHz 200 MHz 200 MHz
Supply Voltage 3.3 V 3.3 V 3.3 V
Output Interface CMOS CMOS CMOS
Operating Temperature Range -40 °C to +85 °C -40 °C to +85 °C -40 °C to +85 °C
Ordering Configuration DS90LV048ATMTC DS90LV048ATMTC/NOPB ordering code DS90LV048ATMTCX/NOPB ordering code

मुख्य विशेषताएँ

  • Four-channel receiver consolidation (बनामDS90LV048ATMTC/NOPB)
  • Pin-compatible Texas Instruments sourcing options (बनामDS90LV048ATMTCX/NOPB)
  • Compact multi-channel LVDS interface (बनामDS90LV048ATMTC/NOPB)

डिज़ाइन नोट्स

Route every LVDS channel as a continuous differential pair over a continuous reference plane. Avoid changing pair width, adding test-probe stubs, or creating unequal branches between the transmitter and receiver. Place any required termination at the receiver end unless the transmitter documentation specifies another topology. This is essential because a discontinuity in the differential path can reflect energy into the link and degrade eye margin.

Place the DS90LV048ATMTC close to the input connector or cable interface when interconnect loss is significant. Keep the four differential pairs away from clocks, switching-power-node traces, and other high-current edges. Maintain a direct ground-return path beneath the pairs, and use the package pin configuration in the manufacturer datasheet to orient routing consistently with the exposed pad or thermal requirements of the selected TSSOP variant.

Connect the 3.3 V supply through a low-impedance plane or trace and place the manufacturer-recommended bypass capacitors immediately beside the supply and ground pins. Four simultaneously operating high-speed channels can produce fast transient current even though the receiver is designed for low power. Avoid sharing a long narrow supply neck between bypass capacitors and the device, because common supply inductance can translate switching current into receiver supply noise.

Do not treat an LVDS receiver as a general-purpose logic input, and do not substitute a line driver such as the DS90LV047A for this receiver. Confirm the pin assignment, input common-mode range, differential threshold, output-enable polarity, termination, and CMOS output voltage levels in the manufacturer datasheet. Also verify that any proposed replacement has the same 16-TSSOP footprint rather than merely a similar receiver function.

अनुपालन जानकारी

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

The manufacturer documentation confirms the 3.3 V operating range, 400 Mbps signaling rate, 16-TSSOP package, and -40 °C to +85 °C temperature range. Specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the applicable Texas Instruments product documentation.

डेटा सत्यापन तिथि: 2026-11-16 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

DS90LV048ATMTC datasheet DS90LV048ATMTC pinout DS90LV048ATMTC datasheet pdf Texas Instruments DS90LV048ATMTC DS90LV048A 400 Mbps receiver DS90LV048ATMTC 16-TSSOP DS90LV048ATMTC equivalent DS90LV048ATMTC replacement DS90LV048ATMTC cross reference DS90LV048ATMTC vs DS90LV048ATMTC/NOPB DS90LV048ATMTC footprint DS90LV048ATMTC application circuit DS90LV048ATMTC price DS90LV048ATMTC stock DS90LV048A LVDS receiver interface

संबंधित कंपोनेंट्स और शब्द

Texas Instruments DS90LV048ATMTC DS90LV048A DS90LV047A DS90LV048ATMTC/NOPB DS90LV048ATMTCX/NOPB LVDS receiver differential line receiver interface IC semiconductor CMOS output LVDS 400 Mbps 200 MHz 3.3 V 16-TSSOP TSSOP package family surface-mount technology SMD package point-to-point interface low voltage differential signaling industrial control test and measurement data acquisition common-mode noise
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें