Texas Instruments

DS90LV110ATMTX - 1:10 200MHz LVDS Clock Distributor | TI

MPN: DS90LV110ATMTX ✓ सक्रिय
3.3 V Vdss 28-pin TSSOP (PW), 0.173 inch, 4.40 mm width Package 200 MHz Speed
न्यूनतम ऑर्डर मात्रा: 1 |

DS90LV110ATMTX अवलोकन

The Texas Instruments DS90LV110ATMTX is a 1-to-10 LVDS data and clock distributor with failsafe operation, a maximum clock frequency of 200 MHz, and a 28-pin TSSOP package. Designed for point-to-point clock distribution, the device accepts one differential input and provides ten differential outputs. It supports 3.3 V operation, LVDS signaling, and output tri-state control through an enable input, making it suitable for timing-heavy backplanes, telecommunications equipment, industrial controls, and test systems.

An LVDS clock distributor is a low-voltage differential signaling interface device that regenerates and distributes a high-speed differential clock across multiple receivers. Its place in the signal-chain hierarchy is clock and timing IC, then clock buffer or driver, then interface logic and semiconductor. Differential signaling reduces sensitivity to common-mode noise, while low swing levels support reliable high-speed data transmission over controlled-impedance printed circuit boards.

The principal features of the DS90LV110ATMTX include ten true outputs, a 200 MHz maximum clock frequency, a 3.9 ns propagation delay, and support for LVDS, CML, and PECL-compatible signaling described for the device. The outputs can enter a high-impedance state through the enable function. Its -40°C to +85°C industrial temperature range supports commercial and industrial equipment, while the gull-wing TSSOP-28 package provides a conventional surface-mount footprint.

The one-input, ten-output topology is important in clock-tree design because it allows a single low-skew source to feed multiple destinations without requiring ten separate buffers. The 400 Mb/s signaling rate and 0.45 V differential output level align the device with low-voltage differential clock and data networks. The failsafe behavior helps define the output state when the input is missing or invalid, helping downstream receivers avoid operating on undefined data.

Typical applications include central clock distribution for telecommunications line cards, synchronized operation across industrial control modules, fanout for backplane endpoints, laboratory instrumentation, and clocking for high-speed interface subsystems. In each case, controlled-impedance routing, matched pair geometry, adequate return-path continuity, and correct termination are essential for maintaining signal integrity.

When laying out the PCB, route each differential pair as a tightly coupled impedance-controlled pair and minimize stub lengths. Keep input and output return paths continuous and place termination components where their physical distance best matches the receiver interface. Use the enable input to place unused outputs in tri-state and verify system-level startup behavior when receivers may be unpowered.

This product page combines the device function, verified package and ordering information, practical clock-distribution design guidance, comparison parameters, and narrowly defined replacement choices. It also identifies which application details require confirmation from the manufacturer datasheet rather than inferring electrical values from a distributor summary.

के लिए ड्रॉप-इन विकल्प DS90LV110ATMTX — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

DS90LV110ATMT

✅ ड्रॉप-इन
Texas Instruments
📦 28-TSSOP (PW)
1-to-10 LVDS data and clock distributor · 1:10 · 200 MHz · 145 ps · 160 mA · 3 V · -40°C to +85°C · LVDS differential signaling

कीमत के लिए संपर्क करें

डेटाशीट देखें →

DS90LV110ATMTX/NOPB

✅ ड्रॉप-इन
📦 28-TSSOP (PW)
Adds the /NOPB lead-free ordering designation; 1:10 fanout, 200 MHz clock rating, 28-pin TSSOP package, and 3.3 V operation remain the same, with 0% change in core functional ratings.

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

DS90LV110ATMT/NOPB

✅ ड्रॉप-इन
📦 28-TSSOP (PW)
Combines the MT ordering suffix with /NOPB; documented package and terminals match, while 1:10 fanout and 200 MHz performance remain unchanged, with 0% change in core ratings.

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

DS90LV110ATMTX Maximum Ratings और Electrical Characteristics

फ़ंक्शन 1-to-10 LVDS data and clock distributor with failsafe
Fanout Ratio 1:10
अधिकतम क्लॉक फ़्रीक्वेंसी 200 MHz
Number of Inputs 1
आउटपुट की संख्या 10
True Output Count 10
Signaling Protocols LVDS, CML, PECL
सप्लाई वोल्टेज 3.3 V
Signaling Rate 400 Mb/s
Differential Output Voltage 0.45 V
Propagation Delay 3.9 ns
Output State Control 3-state output enable
ऑपरेटिंग तापमान रेंज -40°C to +85°C
Temperature Grade Industrial
पैकेज 28-pin TSSOP (PW), 0.173 inch, 4.40 mm width
Terminal Form Gull wing
माउंटिंग प्रकार Surface mount
Shipping Format Tape and reel

DS90LV110ATMTX 28-pin tssop (pw), 0.173 inch, 4.40 mm width पिन कॉन्फ़िगरेशन गाइड

DS90LV110ATMTX (28-pin tssop (pw), 0.173 inch, 4.40 mm width पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस डिजिटल IC में GPIO, संचार इंटरफ़ेस (UART, SPI, I2C) और पावर पिन शामिल हैं। वैकल्पिक पिन फ़ंक्शन और कॉन्फ़िगरेशन विकल्पों के लिए निर्माता डेटाशीट देखें। एम्बेडेड सिस्टम डिज़ाइन और PCB लेआउट के लिए आवश्यक।

DS90LV110ATMTX के लिए 28-pin tssop (pw), 0.173 inch, 4.40 mm width पैकेज पिनआउट आरेख

इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: DS90LV110ATMTX.

देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।

सामान्य अनुप्रयोग

DS90LV110ATMTX के लिए उपयुक्त है 6 अनुप्रयोगs: Telecommunications Line-Card Clock Distribution, Industrial Control Module Clock Fanout, High-Speed Backplane Clock Distribution, Test and Measurement Instrumentation, Synchronized Data Acquisition Systems, Network Interface Timing Hub.

🌐

Telecommunications Line-Card Clock Distribution

The DS90LV110ATMTX fits clock-distribution networks that must send one timing reference to as many as ten line-card or interface sections. Its 1:10 fanout removes the need for ten separate single-output buffers, while the 200 MHz maximum clock frequency supports high-speed digital infrastructure. The 3.3 V supply and LVDS-compatible differential outputs are suitable for compact backplane and board-level implementations. The principal design consideration is maintaining matched differential geometry and equalizing timing across all ten branches. Because the output count is fixed, unused branches can be tri-stated through the enable function. Validate worst-case board skew and receiver loading in the final topology rather than relying only on the device’s 3.9 ns propagation-delay specification.

🏭

Industrial Control Module Clock Fanout

The DS90LV110ATMTX can distribute a common clock to processors, counters, converters, and communication interfaces within an industrial control module. Its -40°C to +85°C industrial temperature range suits equipment operating across extended ambient conditions, while the 28-pin TSSOP package simplifies assembly on conventional surface-mount boards. Ten outputs allow a single source to serve several timing domains without multiplying clock-driver circuits. The design should isolate the clock network from noisy power and switching stages, use controlled-impedance routing, and account for input-to-output skew across the full board. Tri-state control is useful during startup or when a downstream subsystem is not yet ready to accept clock edges.

🖥️

High-Speed Backplane Clock Distribution

The DS90LV110ATMTX is appropriate for distributing a differential clock across multiple backplane endpoints when one source must fan out to ten destinations. Differential signaling and the device’s 400 Mb/s signaling capability provide a suitable interface for controlled-impedance backplanes, while the 1:10 ratio supports parallel endpoint clocking. Signal integrity depends on maintaining continuous reference planes, tightly coupled pair routing, appropriate receiver termination, and minimal vias or stubs. The 200 MHz operating limit should be checked against the clock source, cable, connectors, and endpoint receivers. Engineers should also characterize board-to-board skew across temperature because equal nominal propagation delay does not guarantee identical arrival time after routing losses and connector delays are included.

🧩

Test and Measurement Instrumentation

The DS90LV110ATMTX can provide a common differential clock to multiple acquisition, conversion, or triggering channels in laboratory instrumentation. A single 200 MHz-class source distributed through one device reduces clock-source count and helps keep channel timing organized. The 10 outputs support instrument architectures that need parallel reference clocks, while tri-state enable control can isolate inactive channels. For useful results, the clock source must provide sufficient amplitude and jitter performance, and each output path should be terminated according to the receiving circuit. Because the distributor summary identifies a 3.9 ns propagation delay, timing calibration should account for this latency in trigger relationships. Use the manufacturer application information to select the correct topology and termination arrangement.

📺

Synchronized Data Acquisition Systems

The DS90LV110ATMTX supports synchronized multi-channel data acquisition by distributing one clock to several converters or digital processing sections. Its ten outputs offer enough fanout for compact systems, and the 3.3 V operation integrates naturally with modern mixed-signal and digital hardware. Timing accuracy depends on equal propagation into each acquisition path, so route the differential outputs with matched geometry and keep loading consistent. The reported 3.9 ns propagation delay should be included in trigger-delay calculations. Where unused converter inputs are present, tri-stating their clock branches can reduce unwanted activity. Confirm that each ADC’s clock threshold, jitter tolerance, and maximum input frequency satisfy the datasheet requirements before using the distributor in a precision acquisition chain.

🔧

Network Interface Timing Hub

The DS90LV110ATMTX can act as the timing hub for a network interface card when several serializer, deserializer, or controller domains need a common reference. Ten outputs provide one-to-many distribution while the 28-pin TSSOP package keeps the implementation compatible with established surface-mount assembly methods. The 400 Mb/s signaling-rate description is relevant for low-voltage differential links, but the 200 MHz clock specification remains the governing timing limit. Route input and output pairs away from switching-regulator loops, maintain ground continuity, and place receiver termination close to the load. Enable sequencing can prevent clock delivery to an unpowered endpoint, reducing unwanted state transitions during system startup.

What is the operating voltage of DS90LV110ATMTX?
The DS90LV110ATMTX operates from a 3.3 V supply. According to the Texas Instruments DS90LV110AT product page, the device is a 1-to-10 LVDS data and clock distributor with failsafe in a 28-pin TSSOP package. This supply arrangement makes the part suitable for 3.3 V system timing and interface designs. Confirm decoupling, input termination, and output-receiver requirements against the manufacturer datasheet before committing the circuit.
What is the maximum clock frequency of DS90LV110ATMTX?
The DS90LV110ATMTX supports clock frequencies up to 200 MHz. The distributor product listing identifies it as a 1:10 clock fanout buffer rated at 200 MHz, while the Texas Instruments product page describes it as an LVDS data and clock distributor. The 200 MHz figure establishes the nominal maximum clock input for fanout designs, although actual system operation also depends on source jitter, trace loss, receiver capability, and loading.
How many outputs does DS90LV110ATMTX provide?
The DS90LV110ATMTX provides ten differential outputs from one differential input. The manufacturer identifies the device as a 1-to-10 distributor, and the component listing reports ten true outputs at a nominal 3.3 V supply. Each output can be placed in a tri-state condition using the enable function, which is useful when only part of the clock fanout must remain active.
Where can I download the DS90LV110ATMTX datasheet PDF?
The official DS90LV110ATMTX technical information is available through the Texas Instruments product page at https://www.ti.com/product/DS90LV110AT. Select the DS90LV110ATMTX ordering option to confirm the 28-pin TSSOP variant, -40°C to +85°C temperature range, and relevant ordering information. Use the manufacturer datasheet for the complete electrical table, pin descriptions, application circuit, and recommended termination values.
Where can I find the DS90LV110ATMTX pinout?
The DS90LV110ATMTX pinout is found in the pin-configuration section of the Texas Instruments DS90LV110AT datasheet. The component uses a 28-pin TSSOP package, with the exposed input, ten differential outputs, power pins, ground pins, and enable control distributed across the package. Use the datasheet pin table when assigning PCB nets because the exact signal and supply pin assignments must be followed without substituting a generic TSSOP numbering layout.
Is DS90LV110ATMTX suitable for clock distribution?
Yes, the DS90LV110ATMTX is specifically suitable for one-to-ten differential clock distribution. Its 200 MHz maximum clock frequency, ten outputs, and 3.9 ns propagation delay make it appropriate for distributing a common timing signal to multiple receivers. The design must still control differential impedance, minimize pair stubs, provide the required termination, and verify worst-case skew across all ten loads.
What is the difference between DS90LV110ATMTX and DS90LV110ATMTX/NOPB?
DS90LV110ATMTX and DS90LV110ATMTX/NOPB describe the same 1:10, 200 MHz, 28-pin TSSOP clock-distributor function, but the /NOPB ordering code identifies the lead-free terminal-finish option. The manufacturer ordering information lists both forms for the PW package and the same -40°C to +85°C industrial range. Confirm the current ordering suffix required by your procurement and assembly requirements before treating the two markings as fully interchangeable.
Can DS90LV110ATMT replace DS90LV110ATMTX?
DS90LV110ATMT can serve as a candidate replacement for DS90LV110ATMTX because comparison information identifies matching terminals and package characteristics for the DS90LV110 family. The candidate is not equivalent for every procurement requirement because its ordering suffix differs and the precise packing or terminal-finish configuration must be checked. Verify the exact package drawing, pin assignments, electrical limits, and assembly code in the manufacturer ordering information.
What is the best drop-in replacement for DS90LV110ATMTX?
The closest documented drop-in candidates are DS90LV110ATMT, DS90LV110ATMTX/NOPB, and DS90LV110ATMT/NOPB, all from the same Texas Instruments DS90LV110 family and identified with a 28-pin TSSOP format. The /NOPB versions change the ordering or terminal-finish notation rather than the core 1:10, 200 MHz function. Select the candidate whose exact ordering information, availability, and assembly requirements match the original design.
What can replace DS90LV110ATMTX on the same PCB?
A same-PCB replacement must preserve the 28-pin TSSOP footprint, pin functions, 1:10 distribution function, 3.3 V supply, and differential signaling behavior. The documented DS90LV110 family candidates are DS90LV110ATMT, DS90LV110ATMTX/NOPB, and DS90LV110ATMT/NOPB. Do not substitute a clock buffer with a different fanout ratio or package; verify the exact MPN, pinout, and ordering suffix before production use.
When should I choose DS90LV110ATMTX instead of DS90LV110ATMT?
Choose DS90LV110ATMTX when the original design specifies that exact ordering code and its associated package and finish requirements. Choose DS90LV110ATMT only after confirming that its manufacturer ordering information provides the required footprint, pinout, temperature grade, and terminal finish. Both belong to the same 1:10 DS90LV110 family, but the ordering suffix must be treated as part of the procurement specification rather than an interchangeable label.
Is DS90LV110ATMTX a 400 Mb/s LVDS interface IC?
Yes, the DS90LV110ATMTX is identified as a high-speed LVDS interface device with a 400 Mb/s signaling rate. It distributes one differential input to ten differential outputs and operates from a 3.3 V supply. The 400 Mb/s figure is a device signaling capability, not a guarantee that every board can run at that rate; routing, loss, jitter, source strength, and receiver thresholds must also be evaluated.
Where to buy DS90LV110ATMTX online?
Use the Request a Quote form on this page to ask for DS90LV110ATMTX availability, minimum order quantity, lead time, and the exact suffix required for your assembly. The manufacturer product page and listed distributor results confirm that DS90LV110ATMTX is a cataloged Texas Instruments 1:10, 200 MHz, 28-pin TSSOP device. A quote request avoids committing to an incomplete or incorrect ordering configuration.
What is the price of DS90LV110ATMTX?
The current commercial price for DS90LV110ATMTX is obtained through the Request a Quote form on this page. The available distributor search results do not print an explicit quantity-break price table for this exact ordering code, so no current price figure is asserted here. Include your target quantity, packaging requirement, and acceptable lead time in the request for a quote.
What is the lead time and stock status for DS90LV110ATMTX?
Current stock and lead time for DS90LV110ATMTX should be confirmed through the Request a Quote form on this page. The distributor listing states that the part ships today, but a listing headline alone does not establish a guaranteed quantity for every order size or package suffix. Provide the required quantity and assembly configuration so current availability can be matched to the production plan.
What are the key specifications engineers should know about DS90LV110ATMTX?
The DS90LV110ATMTX is a 3.3 V, 1-to-10 LVDS data and clock distributor rated to 200 MHz. It provides ten true differential outputs, supports LVDS, CML, and PECL signaling, operates over -40°C to +85°C, and uses a 28-pin TSSOP package. Its reported 400 Mb/s signaling rate, 0.45 V differential output, 3.9 ns propagation delay, tri-state output control, and failsafe function define the core engineering envelope.

के लिए इंजीनियरिंग संदर्भ डेटा DS90LV110ATMTX — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose DS90LV110ATMTX when the original BOM specifies that exact ordering code, a one-to-ten LVDS or compatible differential clock distribution function, and a 28-pin TSSOP implementation. DS90LV110ATMT is the practical same-family candidate when its ordering suffix, terminal finish, and procurement requirements satisfy the assembly. DS90LV110ATMTX/NOPB offers the corresponding /NOPB ordering designation, while DS90LV110ATMT/NOPB combines the MT and /NOPB conventions. All documented candidates preserve the 1:10 fanout, 200 MHz clock rating, 3.3 V supply, failsafe function, and 28-pin package. Because these choices differ mainly in ordering and finish notation, the exact manufacturer part-details page should control the final decision. Do not select a candidate solely from the distributor description; confirm pin assignments, package drawings, lifecycle status, and the required assembly suffix.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद DS90LV110ATMT DS90LV110ATMTX/NOPB DS90LV110ATMT/NOPB
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 28-TSSOP (PW) 28-TSSOP (PW) 28-TSSOP (PW) 28-TSSOP (PW)
Fanout Ratio 1:10 1:10 1:10 1:10
Maximum Clock Frequency 200 MHz 200 MHz 200 MHz 200 MHz
Supply Voltage 3.3 V 3.3 V 3.3 V 3.3 V
Signaling Rate 400 Mb/s 400 Mb/s 400 Mb/s 400 Mb/s
Operating Temperature Range -40°C to +85°C -40°C to +85°C -40°C to +85°C -40°C to +85°C
Failsafe Function Yes Yes Yes Yes

मुख्य विशेषताएँ

  • Exact manufacturer ordering configuration (बनामDS90LV110ATMTX/NOPB)
  • Ten-output clock fanout in one package (बनामDS90LV110ATMT)
  • Industrial-temperature DS90LV110 family construction (बनामDS90LV110ATMT/NOPB)

डिज़ाइन नोट्स

Route every LVDS pair as a tightly coupled, impedance-controlled differential pair. Maintain a continuous reference plane, minimize pair-length mismatch, and avoid stubs or unnecessary vias. Place receiver termination according to the manufacturer's recommended topology, and evaluate insertion loss, jitter, and differential voltage at the far end rather than assuming the nominal 400 Mb/s signaling rate guarantees system operation.

Keep the clock input and output routing away from switching nodes and high-current return paths. The input and ten outputs should use consistent geometry and loading so branch delay is not dominated by one route. When unused outputs are not connected to active receivers, use the enable function to place them in tri-state. Verify the exact enable polarity and startup state against the manufacturer pin table and application information.

Do not treat the MT, MTX, and /NOPB ordering variants as procurement-equivalent without checking the assembly requirements. The functional family, 28-pin TSSOP footprint, 1:10 fanout, 200 MHz rating, and 3.3 V operation align across the documented candidates, but terminal-finish and orderable-part details can differ. Confirm the exact MPN, package drawing, pinout, temperature grade, and incoming-inspection requirements before substitution.

अनुपालन जानकारी

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

The device is an industrial-temperature clock distributor rather than an automotive-qualified product. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not stated in the cited product summaries.

डेटा सत्यापन तिथि: 2026-11-16 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

DS90LV110ATMTX datasheet DS90LV110ATMTX pinout DS90LV110ATMTX datasheet pdf DS90LV110ATMTX equivalent DS90LV110ATMTX replacement DS90LV110ATMTX cross reference DS90LV110ATMTX footprint DS90LV110ATMTX price DS90LV110ATMTX stock Texas Instruments DS90LV110ATMTX DS90LV110ATMTX 1:10 200 MHz DS90LV110ATMTX LVDS clock distributor

संबंधित कंपोनेंट्स और शब्द

Texas Instruments DS90LV110ATMTX DS90LV110ATMT DS90LV110ATMTX/NOPB DS90LV110ATMT/NOPB DS90LV110AT LVDS CML PECL clock fanout buffer data and clock distributor clock and timing IC logic IC interface IC semiconductor 28-TSSOP PW package gull-wing package surface mount failsafe 3-state output 200 MHz clock 400 Mb/s signaling rate 3.3 V supply propagation delay industrial temperature grade
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें