DS90LV110ATMTX - 1:10 200MHz LVDS Clock Distributor | TI
料号: DS90LV110ATMTX ✓ 量产中DS90LV110ATMTX 概述
An LVDS clock distributor is a low-voltage differential signaling interface device that regenerates and distributes a high-speed differential clock across multiple receivers. Its place in the signal-chain hierarchy is clock and timing IC, then clock buffer or driver, then interface logic and semiconductor. Differential signaling reduces sensitivity to common-mode noise, while low swing levels support reliable high-speed data transmission over controlled-impedance printed circuit boards.
The principal features of the DS90LV110ATMTX include ten true outputs, a 200 MHz maximum clock frequency, a 3.9 ns propagation delay, and support for LVDS, CML, and PECL-compatible signaling described for the device. The outputs can enter a high-impedance state through the enable function. Its -40°C to +85°C industrial temperature range supports commercial and industrial equipment, while the gull-wing TSSOP-28 package provides a conventional surface-mount footprint.
The one-input, ten-output topology is important in clock-tree design because it allows a single low-skew source to feed multiple destinations without requiring ten separate buffers. The 400 Mb/s signaling rate and 0.45 V differential output level align the device with low-voltage differential clock and data networks. The failsafe behavior helps define the output state when the input is missing or invalid, helping downstream receivers avoid operating on undefined data.
Typical applications include central clock distribution for telecommunications line cards, synchronized operation across industrial control modules, fanout for backplane endpoints, laboratory instrumentation, and clocking for high-speed interface subsystems. In each case, controlled-impedance routing, matched pair geometry, adequate return-path continuity, and correct termination are essential for maintaining signal integrity.
When laying out the PCB, route each differential pair as a tightly coupled impedance-controlled pair and minimize stub lengths. Keep input and output return paths continuous and place termination components where their physical distance best matches the receiver interface. Use the enable input to place unused outputs in tri-state and verify system-level startup behavior when receivers may be unpowered.
This product page combines the device function, verified package and ordering information, practical clock-distribution design guidance, comparison parameters, and narrowly defined replacement choices. It also identifies which application details require confirmation from the manufacturer datasheet rather than inferring electrical values from a distributor summary.
直接替换替代料: DS90LV110ATMTX ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
DS90LV110ATMT
✅ 直接替换联系询价
查看数据手册 →DS90LV110ATMTX/NOPB
✅ 直接替换📋 参考替代料(不在目录中)
DS90LV110ATMT/NOPB
✅ 直接替换📋 参考替代料(不在目录中)
DS90LV110ATMTX 最大额定值与电气特性
| 功能 | 1-to-10 LVDS data and clock distributor with failsafe |
| Fanout Ratio | 1:10 |
| 最大时钟频率 | 200 MHz |
| Number of Inputs | 1 |
| 输出数量 | 10 |
| True Output Count | 10 |
| Signaling Protocols | LVDS, CML, PECL |
| 电源电压 | 3.3 V |
| Signaling Rate | 400 Mb/s |
| Differential Output Voltage | 0.45 V |
| Propagation Delay | 3.9 ns |
| Output State Control | 3-state output enable |
| 工作温度范围 | -40°C to +85°C |
| Temperature Grade | Industrial |
| 封装 | 28-pin TSSOP (PW), 0.173 inch, 4.40 mm width |
| Terminal Form | Gull wing |
| 安装类型 | Surface mount |
| Shipping Format | Tape and reel |
DS90LV110ATMTX 28-pin tssop (pw), 0.173 inch, 4.40 mm width 引脚配置指南
DS90LV110ATMTX(28-pin tssop (pw), 0.173 inch, 4.40 mm width 封装)的引脚配置。 该数字 IC 包含 GPIO、通信接口(UART、SPI、I2C)和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据: DS90LV110ATMTX.
请参阅 数据手册 以查看完整引脚配置。
典型应用
DS90LV110ATMTX 适用于 6 应用s: Telecommunications Line-Card Clock Distribution, Industrial Control Module Clock Fanout, High-Speed Backplane Clock Distribution, Test and Measurement Instrumentation, Synchronized Data Acquisition Systems, Network Interface Timing Hub.
Telecommunications Line-Card Clock Distribution
The DS90LV110ATMTX fits clock-distribution networks that must send one timing reference to as many as ten line-card or interface sections. Its 1:10 fanout removes the need for ten separate single-output buffers, while the 200 MHz maximum clock frequency supports high-speed digital infrastructure. The 3.3 V supply and LVDS-compatible differential outputs are suitable for compact backplane and board-level implementations. The principal design consideration is maintaining matched differential geometry and equalizing timing across all ten branches. Because the output count is fixed, unused branches can be tri-stated through the enable function. Validate worst-case board skew and receiver loading in the final topology rather than relying only on the device’s 3.9 ns propagation-delay specification.
推荐
Industrial Control Module Clock Fanout
The DS90LV110ATMTX can distribute a common clock to processors, counters, converters, and communication interfaces within an industrial control module. Its -40°C to +85°C industrial temperature range suits equipment operating across extended ambient conditions, while the 28-pin TSSOP package simplifies assembly on conventional surface-mount boards. Ten outputs allow a single source to serve several timing domains without multiplying clock-driver circuits. The design should isolate the clock network from noisy power and switching stages, use controlled-impedance routing, and account for input-to-output skew across the full board. Tri-state control is useful during startup or when a downstream subsystem is not yet ready to accept clock edges.
推荐
High-Speed Backplane Clock Distribution
The DS90LV110ATMTX is appropriate for distributing a differential clock across multiple backplane endpoints when one source must fan out to ten destinations. Differential signaling and the device’s 400 Mb/s signaling capability provide a suitable interface for controlled-impedance backplanes, while the 1:10 ratio supports parallel endpoint clocking. Signal integrity depends on maintaining continuous reference planes, tightly coupled pair routing, appropriate receiver termination, and minimal vias or stubs. The 200 MHz operating limit should be checked against the clock source, cable, connectors, and endpoint receivers. Engineers should also characterize board-to-board skew across temperature because equal nominal propagation delay does not guarantee identical arrival time after routing losses and connector delays are included.
推荐
Test and Measurement Instrumentation
The DS90LV110ATMTX can provide a common differential clock to multiple acquisition, conversion, or triggering channels in laboratory instrumentation. A single 200 MHz-class source distributed through one device reduces clock-source count and helps keep channel timing organized. The 10 outputs support instrument architectures that need parallel reference clocks, while tri-state enable control can isolate inactive channels. For useful results, the clock source must provide sufficient amplitude and jitter performance, and each output path should be terminated according to the receiving circuit. Because the distributor summary identifies a 3.9 ns propagation delay, timing calibration should account for this latency in trigger relationships. Use the manufacturer application information to select the correct topology and termination arrangement.
推荐
Synchronized Data Acquisition Systems
The DS90LV110ATMTX supports synchronized multi-channel data acquisition by distributing one clock to several converters or digital processing sections. Its ten outputs offer enough fanout for compact systems, and the 3.3 V operation integrates naturally with modern mixed-signal and digital hardware. Timing accuracy depends on equal propagation into each acquisition path, so route the differential outputs with matched geometry and keep loading consistent. The reported 3.9 ns propagation delay should be included in trigger-delay calculations. Where unused converter inputs are present, tri-stating their clock branches can reduce unwanted activity. Confirm that each ADC’s clock threshold, jitter tolerance, and maximum input frequency satisfy the datasheet requirements before using the distributor in a precision acquisition chain.
推荐
Network Interface Timing Hub
The DS90LV110ATMTX can act as the timing hub for a network interface card when several serializer, deserializer, or controller domains need a common reference. Ten outputs provide one-to-many distribution while the 28-pin TSSOP package keeps the implementation compatible with established surface-mount assembly methods. The 400 Mb/s signaling-rate description is relevant for low-voltage differential links, but the 200 MHz clock specification remains the governing timing limit. Route input and output pairs away from switching-regulator loops, maintain ground continuity, and place receiver termination close to the load. Enable sequencing can prevent clock delivery to an unpowered endpoint, reducing unwanted state transitions during system startup.
推荐
推荐产品汇总
工程参考数据: DS90LV110ATMTX ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | DS90LV110ATMT | DS90LV110ATMTX/NOPB | DS90LV110ATMT/NOPB |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 28-TSSOP (PW) | 28-TSSOP (PW) | 28-TSSOP (PW) | 28-TSSOP (PW) |
| Fanout Ratio | 1:10 | 1:10 | 1:10 | 1:10 |
| Maximum Clock Frequency | 200 MHz | 200 MHz | 200 MHz | 200 MHz |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Signaling Rate | 400 Mb/s | 400 Mb/s | 400 Mb/s | 400 Mb/s |
| Operating Temperature Range | -40°C to +85°C | -40°C to +85°C | -40°C to +85°C | -40°C to +85°C |
| Failsafe Function | Yes | Yes | Yes | Yes |
关键差异点
- Exact manufacturer ordering configuration (对比 DS90LV110ATMTX/NOPB)
- Ten-output clock fanout in one package (对比 DS90LV110ATMT)
- Industrial-temperature DS90LV110 family construction (对比 DS90LV110ATMT/NOPB)
设计说明
Route every LVDS pair as a tightly coupled, impedance-controlled differential pair. Maintain a continuous reference plane, minimize pair-length mismatch, and avoid stubs or unnecessary vias. Place receiver termination according to the manufacturer's recommended topology, and evaluate insertion loss, jitter, and differential voltage at the far end rather than assuming the nominal 400 Mb/s signaling rate guarantees system operation.
Keep the clock input and output routing away from switching nodes and high-current return paths. The input and ten outputs should use consistent geometry and loading so branch delay is not dominated by one route. When unused outputs are not connected to active receivers, use the enable function to place them in tri-state. Verify the exact enable polarity and startup state against the manufacturer pin table and application information.
Do not treat the MT, MTX, and /NOPB ordering variants as procurement-equivalent without checking the assembly requirements. The functional family, 28-pin TSSOP footprint, 1:10 fanout, 200 MHz rating, and 3.3 V operation align across the documented candidates, but terminal-finish and orderable-part details can differ. Confirm the exact MPN, package drawing, pinout, temperature grade, and incoming-inspection requirements before substitution.
合规信息
The device is an industrial-temperature clock distributor rather than an automotive-qualified product. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not stated in the cited product summaries.