ICS581G-02 - 200MHz Zero-Delay Clock Buffer | Renesas
MPN: ICS581G-02 ✗ जीवन की समाप्तिICS581G-02 अवलोकन
A clock multiplexer is an integrated timing device that routes one of several input clocks to a shared output while maintaining controlled phase relationship between the selected sources. Clock buffers reproduce a timing signal across multiple loads to improve fanout and isolate source and destination circuits. The ICS581G-02 combines these functions in a single clock and timing IC, placing it within the PLL-based clock distribution hierarchy used in communications, computing, industrial control, and test equipment.
Key characteristics include a maximum stated operating frequency of 200 MHz, four non-inverted outputs, zero-delay clock distribution, glitch-free multiplexing, and a 16-pin TSSOP package with 0.65 mm pitch. The four-output arrangement allows a single device to feed several clock domains while reducing the number of separate buffers required on the printed circuit board. Its TSSOP package supports compact surface-mount construction and automated assembly.
Technically, the ICS581G-02 uses a PLL-based architecture to generate the distributed clock outputs. PLL-based distribution can compensate for clock-path phase differences and provide predictable output relationships when the device is switched between operating modes. Because the manufacturer identifies the part as a zero-delay glitch-free clock multiplexer, designers can use it where source selection and output fanout must occur without introducing an intentional cycle delay at the output.
Typical uses include processor and FPGA clock distribution, communications-module clock routing, data-converter clock fanout, industrial control systems, and instrumentation requiring several outputs from one timing source. The device is also appropriate where a design needs to select between clock sources without relying on discrete multiplexer and buffer combinations. Placement near the loads can reduce trace-related skew and improve clock distribution across a board.
Layout is especially important because a clock device can perform correctly in principle but fail in the assembled PCB if input traces, output loads, and return paths are poorly matched. Keep the clock inputs and outputs over a continuous reference plane, minimize stub branches, place decoupling close to the supply pins, and maintain a symmetric output-routing arrangement. Review the pin-description and layout guidance in the manufacturer datasheet before finalizing fanout and return-path geometry.
This product page combines the verified device characteristics, supported ordering variants, application guidance, and comparison criteria to help engineers evaluate the ICS581G-02 for zero-delay clock multiplexing and fanout designs. It also highlights which electrical and pin-level details must be confirmed from the manufacturer datasheet before production release.
के लिए ड्रॉप-इन विकल्प ICS581G-02 — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
ICS581G-02ILF
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
ICS581G-02LF
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
ICS581G-02I
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
ICS581G-02IT
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
ICS581G-02T
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
ICS581G-02 विशेषताएं
| Product Type | Fanout buffer, zero-delay buffer, and glitch-free clock multiplexer |
| Maximum Stated Frequency | 200 MHz |
| Architecture | PLL-based |
| Number of True Outputs | 4 outputs |
| Number of Inverted Outputs | 0 outputs |
| Input-to-Output Delay | Zero delay |
| Clock Multiplexing | Glitch-free |
| पैकेज | 16-pin TSSOP |
| Package Width | 4.40 mm |
| Lead Pitch | 0.65 mm |
| माउंटिंग प्रकार | Surface mount |
| RoHS स्थिति | Compliant |
| Standard Package Code | PDSO16 |
ICS581G-02 pdso16 पिन कॉन्फ़िगरेशन गाइड
ICS581G-02 (pdso16 पैकेज) के लिए पिन कॉन्फ़िगरेशन। पिन नंबरिंग, फ़ंक्शन और कनेक्शन आरेख निर्माता डेटाशीट में परिभाषित हैं। सटीक फुटप्रिंट और सोल्डरिंग दिशानिर्देशों के लिए इसे देखें।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: ICS581G-02.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
ICS581G-02 के लिए उपयुक्त है 6 अनुप्रयोगs: FPGA Clock Distribution, Communications Clock Routing, Industrial Control Systems, Data Converter Clock Fanout, Test and Measurement Equipment, Processor and Memory Clock Networks.
FPGA Clock Distribution
The ICS581G-02 fits FPGA clock-distribution schemes requiring one timing source to feed several logic regions without using separate one-output buffers. Its 200 MHz operating rating covers many moderate-speed FPGA clock networks, while the PLL-based zero-delay architecture and four true outputs provide a compact fanout solution. Place the device close to the clock-consuming devices and route outputs with matched geometry to limit relative skew. Confirm the FPGA input specification, target operating frequency, permissible jitter, and output-load limits before finalizing the design.
अनुशंसित
Communications Clock Routing
The ICS581G-02 is suitable for communications equipment that must select and distribute a clock among multiple functional blocks. The zero-delay glitch-free multiplexing function supports controlled clock transfer, and four outputs can feed converters, controllers, interface logic, and memory from one package. At clock rates up to 200 MHz, transmission-line geometry, return paths, and load balance become important. The device should be evaluated against the receiver's jitter and setup requirements, with input and output timing verified from the manufacturer documentation.
अनुशंसित
Industrial Control Systems
ICS581G-02-based clock networks can support controller, data-converter, and communications timing in industrial control equipment. A single PLL-based multiplexer with four true outputs reduces the number of discrete clock components and provides a clear central point for distributing a selected reference. The 200 MHz capability is useful for digital control subsystems operating below that limit, although the industrial system's temperature, supply, and EMC requirements must be checked against the exact ordering suffix. Keep the clock network isolated from noisy switching paths and validate performance across line conditions.
अनुशंसित
Data Converter Clock Fanout
The ICS581G-02 can provide synchronized clock outputs to multiple data converters and related digital processing stages. Four true outputs allow several converter clock pins to be driven from a common timing source without adding separate buffer packages. The zero-delay design helps preserve the intended relationship between input and output clocks, while glitch-free multiplexing supports controlled source selection. The actual suitability depends on converter setup-and-hold limits, converter input-jitter requirements, trace skew, and the number and capacitance of connected loads.
अनुशंसित
Test and Measurement Equipment
The ICS581G-02 is useful in instrumentation that must distribute a stable reference clock to acquisition, processing, and conversion sections. Four outputs support a compact multi-load topology, while the PLL-based zero-delay arrangement helps maintain predictable clock relationships across the system. For instruments sensitive to source-to-output delay and edge quality, route each output over a continuous plane and avoid unnecessary stubs. Verify the instrument's allowable jitter, skew, clock amplitude, and maximum operating frequency before selecting the exact ordering suffix.
अनुशंसित
Processor and Memory Clock Networks
A four-output ICS581G-02 can serve processor, memory, peripheral, and bus-interface clock networks where multiple loads require a common source. Its 200 MHz specification and zero-delay classification make it appropriate for moderate-speed systems, while the integrated multiplexer reduces discrete component count. The designer should account for simultaneous-switching noise, supply sensitivity, output jitter, and per-receiver timing margins. Keep clock traces short where practical and use matched routing so the device's fanout advantage is not lost to board-induced skew.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा ICS581G-02 — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | ICS581G-02ILF | ICS581G-02LF | ICS581G-02I | ICS581G-02IT | ICS581G-02T |
|---|---|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 16-TSSOP | 16-TSSOP - same | 16-TSSOP - same | 16-TSSOP - same | 16-TSSOP - same | 16-TSSOP - same |
| Maximum Stated Frequency | 200 MHz | 200 MHz | 200 MHz | 200 MHz | 200 MHz | 200 MHz |
| Device Category | Fanout buffer, zero-delay buffer, and glitch-free clock multiplexer | Fanout buffer, zero-delay buffer, and glitch-free clock multiplexer | ICS581G zero-delay clock-multiplexer family | ICS581G zero-delay clock-multiplexer family | Clock buffer and distribution device | ICS581G zero-delay clock-multiplexer family |
| Number of True Outputs | 4 outputs | 4 outputs | 4 outputs | 4 outputs | 4 outputs | 4 outputs |
| Package Width | 4.40 mm | 4.40 mm | 4.40 mm | 4.40 mm | 4.40 mm | 4.40 mm |
| Lead Pitch | 0.65 mm | 0.65 mm | 0.65 mm | 0.65 mm | 0.65 mm | 0.65 mm |
मुख्य विशेषताएँ
- Combines zero-delay multiplexing with four-output fanout (बनामICS581G-02ILF)
- Provides four non-inverted clock outputs from one package (बनामICS581G-02LF)
- Supports controlled clock-source selection without intentional input-to-output delay (बनामICS581G-02I)
- Combines four clock outputs in a compact 0.65 mm-pitch TSSOP (बनामICS581G-02IT)
डिज़ाइन नोट्स
Route clock inputs and outputs over a continuous reference plane and keep branches short. Use matched geometry for outputs serving equivalent loads, avoid unnecessary test-point stubs, and place the device close to the receiving clock inputs. The four outputs should not be routed as unequal fanouts if minimum output-to-output skew is important. Use the manufacturer pin-description and recommended-layout material to confirm the intended connection of every TSSOP lead.
Confirm output rise time, edge rate, capacitive-load tolerance, jitter, and maximum operating frequency before enabling all four outputs at 200 MHz. Long traces, unequal loading, and nearby switching nodes can degrade clock quality even when the nominal fanout count is supported. Maintain a continuous return path beneath clock routes and observe the device's source and load rules. A scope measurement at each receiver is appropriate when the design has tight setup-time, skew, or jitter margins.
Do not treat an ordering suffix as interchangeable until the manufacturer ordering table has been checked for temperature grade, shipping form, qualification, and marking. The verified family listings support common 16-TSSOP package and 200 MHz function, but they do not establish every suffix-specific electrical or compliance detail. Also avoid assuming that a general four-output clock buffer is a drop-in replacement; pin assignments, control logic, PLL behavior, and timing characteristics must match the ICS581G-02 design.
Follow the manufacturer's bypass and power-routing recommendations for the exact ICS581G-02 ordering option. Place the required decoupling capacitance close to the supply and ground pins, provide a low-impedance supply connection, and keep high-current return paths away from clock inputs. The verified product summaries do not state the supply-voltage range or recommended capacitor values, so these must be obtained from the manufacturer datasheet before component selection and PCB release.
अनुपालन जानकारी
The ICS581G family cross-reference information identifies the PDSO16 package as RoHS compliant. No verified information establishes REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status for this exact ordering suffix.