INA110KUG4 - 2.5 MHz Military Instrumentation Amplifier | Texas Instruments
MPN: INA110KUG4 ✓ सक्रियINA110KUG4 अवलोकन
An instrumentation amplifier is a precision analog building block that amplifies the voltage difference between two input signals while rejecting common-mode interference. Unlike a general-purpose operational amplifier, an instrumentation amplifier normally incorporates a high-impedance differential input stage, accurate gain-setting resistors, and a low-impedance output stage. Within the power-management and signal-chain hierarchy, it sits upstream of analog-to-digital converters, filters, and analog-to-digital output stages.
The INA110KUG4 is classified by Texas Instruments as an instrumentation amplifier rather than a standalone operational amplifier. Its adjustable external gain resistor allows the same circuit topology to support multiple sensitivity ranges, provided that resistor values remain suitable for the required bandwidth and stability. The 2.5 MHz gain-bandwidth figure makes the device relevant to moderate-bandwidth sensor conditioning rather than only static measurement systems.
Because the INA110KUG4 uses a precision differential input stage, it is suitable for conditioning low-level sensor outputs where common-mode voltage varies relative to the measurement. Typical signal sources include pressure bridges, strain gauges, thermocouples when paired with suitable cold-junction compensation, and high-impedance sensing elements. A reference pin also permits the output voltage to be shifted when the receiving circuit cannot tolerate a ground-centered signal.
Common applications include industrial process monitoring, laboratory instrumentation, data acquisition, medical monitoring equipment, and portable measurement systems. In a typical bridge-sensor circuit, the INA110KUG4 amplifies the small differential bridge voltage while rejecting much of the common excitation voltage. The output can then feed an analog-to-digital converter or an analog filter.
When laying out a board for the INA110KUG4, keep the gain-setting resistor close to its corresponding device pin and use a quiet analog ground for the reference and supply-return connections. Place input and reference decoupling capacitors near the package, and route sensitive input traces away from digital clocks, switching-regulator nodes, and high-current return paths.
This page combines the manufacturer part identity, package information, commercial listings, and comparison data for the INA110KUG4 with application guidance, layout cautions, and practical sourcing information. Review the complete manufacturer datasheet for the definitive pin configuration, electrical limits, gain equation, and recommended operating conditions before releasing a production design.
के लिए ड्रॉप-इन विकल्प INA110KUG4 — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस सीरीज़ के वेरिएंट
समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं INA110KUG4 (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Package, Product Type, RoHS Status.
INA110KU
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →INA110KUG4 Maximum Ratings और Electrical Characteristics
| Product Type | Instrumentation Amplifier |
| Number of Circuits | 1 circuit |
| Gain-Bandwidth Product | 2.5 MHz |
| पैकेज | 16-SOIC |
| Lead Form | Gull wing |
| Package Body Width | 7.50 mm |
| Temperature Grade | Military |
| Typical Dual Supply Voltage | ±15 V |
| माउंटिंग प्रकार | Surface mount |
| RoHS स्थिति | RoHS |
INA110KUG4 7.50 mm पिन कॉन्फ़िगरेशन गाइड
INA110KUG4 (7.50 mm पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस एनालॉग कंपोनेंट में इनपुट, आउटपुट और पावर सप्लाई पिन हैं। ऑफ़सेट नल, कम्पनसेशन और एनेबल पिन कॉन्फ़िगरेशन के लिए निर्माता डेटाशीट देखें। सिग्नल कंडीशनिंग और एम्प्लीफ़ायर सर्किट के लिए आदर्श।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: INA110KUG4.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
INA110KUG4 के लिए उपयुक्त है 6 अनुप्रयोगs: Bridge and Strain-Gauge Sensor Conditioning, Laboratory Data-Acquisition Front End, Industrial Process Monitoring, Medical and Physiological Monitoring, Portable Battery-Powered Instrumentation, Precision Current and Voltage Monitoring.
Bridge and Strain-Gauge Sensor Conditioning
The INA110KUG4 fits bridge-based measurements because an instrumentation amplifier responds to the differential bridge voltage while rejecting the common excitation voltage present on both sensor nodes. The 2.5 MHz gain-bandwidth product supports moderate-bandwidth conditioning rather than only static temperature readings. Place the device close to the bridge, route the two input pairs as closely matched geometry as practical, and use the manufacturer gain equation to select the external gain resistor. Verify the maximum sensor excursion against both input overload and output-swing limits.
अनुशंसित
Laboratory Data-Acquisition Front End
The INA110KUG4 can condition low-level laboratory inputs before conversion by a higher-resolution ADC. Its instrumentation-amplifier topology provides differential input handling and common-mode rejection, while the 16-SOIC package simplifies conventional surface-mount assembly. Use a clean reference voltage and place the external gain resistor close to the device to minimize pickup. Select the closed-loop gain so that the largest expected input, including transients and calibration tolerance, keeps the output within the usable swing.
अनुशंसित
Industrial Process Monitoring
The INA110KUG4 is applicable to industrial monitoring circuits that measure a small differential signal superimposed on a larger common-mode voltage. The 2.5 MHz listed gain-bandwidth product leaves room for signal conditioning beyond extremely slow process variables. Keep sensitive traces away from motor drive and switching-power stages, use a single-point analog return strategy, and check the military-grade ordering option against the installation's environmental requirements. Filtering belongs ahead of the amplifier when out-of-band interference could cause input overload.
अनुशंसित
Medical and Physiological Monitoring
The INA110KUG4 can amplify differential physiological or sensor signals in a monitoring system, provided its noise, offset, common-mode range, and environmental characteristics satisfy the complete design specification. The military-temperature-grade ordering code is useful when the equipment faces a broad ambient range. A typical signal path places the sensor close to the amplifier, followed by protection, filtering, and digitization. Apply the medical product's required safety, isolation, leakage, and EMC controls rather than relying on amplifier selection alone.
अनुशंसित
Portable Battery-Powered Instrumentation
The INA110KUG4 can serve as the low-level analog front end in portable measurement equipment where sensor output is small and supply headroom is limited. Because it is an instrumentation amplifier rather than a switching converter, the signal path adds no switching ripple to the measurement. Verify the exact supply-current demand and operating-voltage limits in the manufacturer datasheet, then use low-noise bypass capacitors and a low-noise reference. The 16-SOIC footprint supports compact layouts, although analog ground separation remains important.
अनुशंसित
Precision Current and Voltage Monitoring
The INA110KUG4 is useful when a monitor must distinguish a small differential measurement from a larger common-mode voltage. The differential input arrangement can measure the voltage across a shunt, the drop across a precision sense element, or another small series voltage. Set gain with the external resistor while keeping the input transient within the device's allowed range. Provide Kelvin-style routing where possible so that supply-drop and copper resistance do not add directly to the measured difference.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा INA110KUG4 — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | INA110KU |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 16-SOIC | 16-SOIC |
| Device Type | Instrumentation Amplifier | Instrumentation Amplifier |
| Number of Circuits | 1 circuit | 1 circuit |
मुख्य विशेषताएँ
- Military-grade ordering option (बनामINA110KU)
- Matched package family (बनामINA110KU)
- Published signal-path bandwidth (बनामINA110KU)
डिज़ाइन नोट्स
Keep the two differential input paths short, closely matched, and isolated from clocks, switching-regulator outputs, and relay contacts. Place the external gain-setting resistor close to its designated device pin to minimize parasitic resistance and noise pickup. A grounded guard or shielding strategy can help on boards with high-level analog inputs, but the complete return-current path must remain continuous so that sensor current does not flow through the input-reference node.
Do not select gain solely from the wanted output voltage. Confirm that the maximum differential input, expected sensor overrange, output swing, and closed-loop bandwidth all remain within the manufacturer operating limits. The 2.5 MHz gain-bandwidth figure is a device-level specification, not a promise that every gain setting provides 2.5 MHz of signal bandwidth. Recalculate the usable bandwidth and stability margin for the final external resistor and load.
Decouple the supply pins directly at the package and return the bypass-current path to the device ground without sharing a long path with digital output currents. Use a low-noise reference at the reference connection and avoid allowing reference ripple to modulate the output. Validate common-mode headroom during startup and supply ramp because an instrumentation amplifier can encounter input voltages outside its useful linear range even when the differential signal is small.
अनुपालन जानकारी
RoHS is explicitly identified in the LCSC product listing. Other compliance fields are not established by the available product records and remain unknown.