INA114AU/1K - 1MHz Precision Instrumentation Amplifier | TI
MPN: INA114AU/1K ✓ सक्रियINA114AU/1K अवलोकन
An instrumentation amplifier is a specialized analog signal-conditioning IC designed to amplify the voltage difference between two inputs while rejecting common-mode signals. Its typical hierarchy is instrumentation amplifier → differential amplifier → analog amplifier → semiconductor. This category is especially useful when a low-level sensor output must be measured in the presence of a larger shared voltage. The INA114 uses a three-op-amp architecture, which provides high input impedance, flexible gain control, and accurate differential amplification.
The INA114's principal electrical features include a 1 MHz gain-bandwidth product, 110 dB dynamic range as identified in the manufacturer listings, 50 µV typical offset, and 11 nV/√Hz input noise density. A single gain-setting resistor establishes gains between 1 and 10,000, eliminating the need for a resistor network. The device can operate with power supplies as low as ±2.25 V and supports dual supplies up to ±18 V. Internal input protection can withstand input voltages up to ±40 V without damage, adding robustness in industrial measurement systems.
Internally, the INA114 uses a versatile three-op-amp instrumentation-amplifier arrangement. Its input stage preserves the differential signal while the output stage develops the selected gain and drives the output relative to the REF pins. The laser-trimmed internal resistors support low offset and consistent performance without user calibration. The manufacturer identifies the INA114 as a low-cost, general-purpose precision device, while its 1 MHz bandwidth allows it to handle signals substantially faster than static low-frequency sensor outputs.
Typical uses include bridge and strain-gauge signal conditioning, current-shunt measurement, low-level sensor interfaces, laboratory instrumentation, and industrial process-control inputs. It is particularly appropriate when a sensor develops only millivolts or microvolts and common-mode voltage can be much larger than the desired signal. The adjustable gain also supports transducers with widely different output sensitivities without changing the surrounding analog topology.
When laying out the circuit, connect the gain resistor between the designated RG pins and place input, supply, and reference bypassing capacitors close to the associated package pins. Keep sensitive input traces short, route them away from switching nodes, and use a stable low-noise reference when an offset voltage other than ground is required. Confirm input and output common-mode ranges over the complete supply range because the selected gain reduces allowable output swing.
This page combines manufacturer specifications, exact-order information, a same-package electrical alternative, and practical design guidance. It also distinguishes reel-packaged ordering variants from genuinely different functions, helping engineers make a defensible selection without relying on package code alone.
के लिए ड्रॉप-इन विकल्प INA114AU/1K — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस सीरीज़ के वेरिएंट
समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं INA114AU/1K (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Amplifier Type, Package.
INA114AU
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →INA114AU/1K Maximum Ratings और Electrical Characteristics
| Amplifier Type | Precision instrumentation amplifier |
| Number of Channels | 1 channel |
| Gain-Bandwidth Product | 1 MHz |
| Typical Offset Voltage | 50 µV |
| Input Noise Density | 11 nV/√Hz |
| क्वाइसेंट करंट | 3 mA |
| Gain Range | 1 to 10,000 |
| Gain Configuration | One external resistor |
| Minimum Total Supply Voltage | ±2.25 V |
| Maximum Total Supply Voltage | ±36 V |
| Minimum Operating Temperature | -40 °C |
| Maximum Operating Temperature | +85 °C |
| Internal Input Protection | ±40 V |
| Architecture | Three-op-amp design |
| Dynamic Range | 110 dB |
| पैकेज | 16-pin SOIC |
| माउंटिंग प्रकार | Surface mount |
| Orderable Package Option | 16-pin SOIC tape and reel |
INA114AU/1K पिन कॉन्फ़िगरेशन
| पिन 1 | RG — Gain resistor connection |
| पिन 2 | IN- — Inverting input |
| पिन 3 | IN+ — Noninverting input |
| पिन 4 | V- — Negative supply connection |
| पिन 5 | REF1 — Reference input 1 |
| पिन 6 | REF2 — Reference input 2 |
| पिन 7 | V+ — Positive supply connection |
| पिन 8 | OUT — Amplified output |
| पिन 9 | RG — Gain resistor connection |
| पिन 10 | NC — Not connected |
| पिन 11 | NC — Not connected |
| पिन 12 | NC — Not connected |
| पिन 13 | NC — Not connected |
| पिन 14 | NC — Not connected |
| पिन 15 | NC — Not connected |
| पिन 16 | NC — Not connected |
सामान्य अनुप्रयोग
INA114AU/1K के लिए उपयुक्त है 6 अनुप्रयोगs: Strain-Gauge Bridge Signal Conditioning, Current-Shunt Measurement, Precision Sensor Front Ends, Laboratory Instrumentation, Industrial Process-Control Inputs, Audio and Communications Interfaces.
Strain-Gauge Bridge Signal Conditioning
The INA114AU/1K fits strain-gauge and resistive-bridge measurement because its gain can be set from 1 to 10,000 with one external resistor. The 50 µV typical offset helps preserve accuracy when the useful bridge imbalance is small, while 11 nV/√Hz input noise supports low-level sensor work. Place the device across the bridge excitation return and differential outputs, with short input traces and local supply bypassing. Verify output headroom at the selected gain because higher amplification reduces the allowable output range relative to the supply rails.
अनुशंसित
Current-Shunt Measurement
The INA114AU/1K is appropriate for measuring the small voltage generated by a current-sense shunt while rejecting the shunt's common-mode voltage. Its differential three-op-amp architecture supports the required subtraction, and the adjustable gain from 1 to 10,000 can compensate for shunt resistance and full-scale current. The 1 MHz bandwidth accommodates rapidly changing current waveforms, while 3 mA power consumption suits compact power converters. Keep the shunt connections short and pair them with a ground-referenced reference configuration unless bidirectional current requires an offset reference.
अनुशंसित
Precision Sensor Front Ends
The INA114AU/1K provides a practical analog front end for low-level pressure, temperature, position, and chemical sensors whose outputs are smaller than their common-mode voltage. Gain can be adapted by replacing one resistor rather than redesigning the amplifier network, and the 50 µV typical offset reduces signal-chain error. The 11 nV/√Hz noise density is useful for low-noise sensor conditioning, although the 1 MHz bandwidth should be evaluated against the sensor's noise bandwidth. Stable bypassing and careful grounding are necessary to preserve the precision promised by the instrumentation-amplifier architecture.
अनुशंसित
Laboratory Instrumentation
The INA114AU/1K suits laboratory front ends that amplify weak differential signals generated by sensors, transducers, or diagnostic fixtures. Its gain can span 1 to 10,000, allowing one design to cover multiple measurement ranges, and the 1 MHz bandwidth is sufficient for many dynamic bench signals. The low 3 mA power consumption supports portable instruments, while operation from ±2.25 V permits lower-voltage designs. Use the REF pins to establish the output midpoint in bipolar or single-supply systems and validate input and output swing at the highest gain used.
अनुशंसित
Industrial Process-Control Inputs
The INA114AU/1K can condition low-level process signals before they enter industrial controllers or data-acquisition systems. Its 1 MHz bandwidth handles more than static sensor readings, and internal input protection up to ±40 V improves tolerance of wiring transients. The single-resistor gain setting supports different transducers without complex analog switching. For reliable operation, maintain common-mode operation within the range allowed by the selected gain, isolate sensitive traces from motor and relay wiring, and use local supply decoupling to prevent switching disturbances from entering the measurement path.
अनुशंसित
Audio and Communications Interfaces
The INA114AU/1K can amplify low-level balanced audio or communications signals when common-mode rejection is more important than absolute ground referencing. Its three-op-amp differential design reduces unwanted common-mode pickup, while gain can be increased to 10,000 for weak sources. The 1 MHz bandwidth exceeds the audible range and also supports higher-bandwidth communication waveforms. The trade-off is that the selected gain reduces output swing, so the source amplitude, input common-mode voltage, reference level, and output clipping must be checked together before deployment.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा INA114AU/1K — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | INA114AU |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 16-pin SOIC | 16-pin SOIC |
| Function | Precision instrumentation amplifier | Precision instrumentation amplifier |
| Channels | 1 channel | 1 channel |
| Gain-Bandwidth Product | 1 MHz | 1 MHz |
| Offset Voltage | 50 µV typical | 50 µV typical |
| Input Noise Density | 11 nV/√Hz | 11 nV/√Hz |
| Gain Range | 1 to 10,000 | 1 to 10,000 |
| Minimum Supply | ±2.25 V | ±2.25 V |
| Operating Temperature | -40 °C to +85 °C | -40 °C to +85 °C |
मुख्य विशेषताएँ
- Combines precision gain control with a 1 MHz bandwidth (बनामINA114AU)
- Single-resistor gain programming simplifies analog layouts (बनामINA114AU)
- Low-noise precision suitable for differential sensing (बनामINA114AU)
डिज़ाइन नोट्स
Route the IN+ and IN- connections as a closely coupled differential pair and keep them short, away from switching nodes, relay contacts, and high-current paths. Place the gain-setting resistor directly between the two RG pins, and place supply-bypass capacitors close to V+ and V-. The 16-pin SOIC has only eight functional connections, but the unused pins must remain unconnected according to the manufacturer pin description.
The INA114 is specified for dual supplies from ±2.25 V to ±18 V. In a single-supply design, verify that the input common-mode voltage and output swing remain valid at the chosen gain. The REF pins establish the output reference; grounding them provides a ground-centered output, while another reference level may be required for biased or bidirectional measurements. Do not exceed the normal operating supply range even though the input stage can withstand transient voltages up to ±40 V.
Use a compact ground reference and avoid introducing copper paths that share current with motors, relays, or switching regulators. Low-level bridge and shunt measurements are particularly sensitive to ground gradients. Keep the gain resistor physically close to the device, use short input traces, and evaluate the total noise bandwidth: the 1 MHz gain-bandwidth capability is useful for dynamic signals, but the lowest noise is obtained by restricting the bandwidth to the measurement requirement.
अनुपालन जानकारी
The manufacturer product information identifies the INA114 as a general-purpose precision instrumentation amplifier, but no specific RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification declaration is present in the cited product information.