Renesas Electronics

ISL81487IB 5V 5Mbps RS-485/RS-422 Transceiver | Renesas

MPN: ISL81487IB ✗ जीवन की समाप्ति
5 V Vdss 8-SOIC Package
न्यूनतम ऑर्डर मात्रा: 1 |

ISL81487IB अवलोकन

Renesas Electronics ISL81487IB is a 5 V, single-channel RS-485/RS-422 half-duplex transceiver with a 5 Mbps maximum data rate, 1/8-unit-load driver capability, and 70 mV receiver hysteresis in an 8-pin SOIC package. Designed for balanced industrial communication links, it combines one driver and one receiver to support two-wire RS-485 buses or point-to-point RS-422 links.

An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into differential balanced signals for reliable communication over cables and noisy industrial environments. The RS-422 standard supports point-to-point, full-duplex signaling, while RS-485 allows multiple drivers and receivers on a shared half-duplex bus. The ISL81487IB belongs to the broader interface-IC hierarchy and is designed for low-power, 5 V system rails.

Key characteristics include a 1/8-unit-load receiver input, a 70 mV receiver hysteresis, operation from a 5 V supply, and a maximum data rate of 5 Mbps. Its fractional unit load permits more nodes on an RS-485 bus than a conventional one-unit-load receiver. The 8-SOIC surface-mount package also supports compact, automated PCB assembly while exposing a standard leaded footprint rather than a fine-pitch land pattern.

The BiCMOS transceiver architecture provides low-power operation for equipment that communicates over cables longer than the short reach of ordinary logic signals. Differential signaling improves common-mode noise rejection, while the low unit-load rating supports networks containing several transceivers. Because the ISL81487IB supports both RS-485 and RS-422, one device can serve industrial controllers, data-acquisition equipment, building automation, and point-to-point instrument interfaces.

Typical uses include factory-floor sensor networks, industrial control gateways, serial port extenders, and remote I/O modules. In an RS-485 installation, the transceiver is placed between a UART or microcontroller and the balanced bus. Direction control determines whether the transmitter or receiver is enabled, while termination and biasing must be designed according to the cable topology.

The primary layout consideration is keeping the balanced driver and receiver paths short, symmetrical, and physically separated from noisy switching circuits. Place termination components at the physical ends of the bus rather than beside every transceiver. Check the transceiver state during startup so that multiple drivers do not contend on the bus, and verify that the selected line baud rate remains within the device's 5 Mbps capability.

This product data combines operating characteristics, lifecycle information, package details, drop-in family alternatives, comparison parameters, and practical interface-design guidance. It is intended to accelerate component evaluation and PCB planning while making the distinctions between the original ISL81487IB and related Renesas family members explicit.

के लिए ड्रॉप-इन विकल्प ISL81487IB — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

इस सीरीज़ के वेरिएंट

समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं ISL81487IB (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Package, Product Type.

Renesas Electronics
Package: 8-pin SOIC
Product Type: Single RS-485/RS-422 transceiver
इसके साथ तुलना करें ISL81487IB →

ISL81487L

✅ ड्रॉप-इन
📦 8-SOIC
ESD-protected member of the ISL81487 family; supply voltage, 1/8-unit-load interface, and 5 Mbps data-rate class remain comparable, with protection rating requiring confirmation

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

ISL81487E

✅ ड्रॉप-इन
📦 8-SOIC
ESD-protected family member with the same 8-SOIC RS-485/RS-422 transceiver footprint; ESD level differs from the original ISL81487IB

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

ISL8487E

✅ ड्रॉप-इन
📦 8-SOIC
Same 5 V, 1/8-unit-load RS-485/RS-422 class and 8-SOIC footprint; ESD protection is specified while the original ISL81487IB has different protection characteristics

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

ISL81487IB विशेषताएं

Product Type Single-channel RS-485/RS-422 transceiver
सप्लाई वोल्टेज 5 V
डेटा दर 5 Mbps
Number of Drivers 1
Number of Receivers 1
Duplex Mode Half duplex
Receiver Unit Load 1/8 unit load
Receiver Hysteresis 70 mV
Supported Protocols RS-422 and RS-485
Logic Technology BiCMOS
ऑपरेटिंग तापमान रेंज -40°C to +85°C
पैकेज 8-SOIC
माउंटिंग स्टाइल Surface mount
Packaging Type Tube

ISL81487IB 8-soic पिन कॉन्फ़िगरेशन गाइड

ISL81487IB (8-soic पैकेज) के लिए पिन कॉन्फ़िगरेशन। पिन नंबरिंग, फ़ंक्शन और कनेक्शन आरेख निर्माता डेटाशीट में परिभाषित हैं। सटीक फुटप्रिंट और सोल्डरिंग दिशानिर्देशों के लिए इसे देखें।

ISL81487IB के लिए 8-soic पैकेज पिनआउट आरेख

इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: ISL81487IB.

देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।

सामान्य अनुप्रयोग

ISL81487IB के लिए उपयुक्त है 6 अनुप्रयोगs: Industrial RS-485 Sensor Networks, Building Automation Gateways, Remote I/O Modules, Data Acquisition Equipment, RS-422 Point-to-Point Links, Serial Port and Cable Extenders.

🏭

Industrial RS-485 Sensor Networks

The ISL81487IB fits distributed sensor networks where multiple remote measurement nodes must share a balanced bus. Its 1/8-unit-load receiver minimizes the loading contributed by each node, while the 5 Mbps maximum data rate supports fast polling and update cycles. Place the transceiver between the node controller and the RS-485 pair, use a controlled driver-enable signal, and install termination only at the two physical bus ends. The -40°C to +85°C operating range is appropriate for many industrial cabinets, although surge and isolation requirements should be handled separately.

🧩

Building Automation Gateways

The ISL81487IB is suitable for building-automation controllers that connect an embedded processor to an RS-485 floor network. Its 5 V supply aligns with many 5 V controller platforms, while the half-duplex one-driver/one-receiver arrangement supports request-and-response communication with remote modules. The 1/8-unit-load input allows several nodes to share a bus, and the 5 Mbps device rating provides ample margin for typical building-control traffic. Designers should still model cable length, common-mode range, grounding, and transient protection at the field connector.

⚡

Remote I/O Modules

The ISL81487IB provides a compact interface between a controller and remote digital or analog I/O stations connected by an RS-485 backbone. Its 8-SOIC package is easy to route on both legacy and new controller boards, and its 1/8-unit-load receiver supports a larger node count than a one-unit-load transceiver. The single transmitter is controlled by a direction signal, allowing the same balanced pair to carry commands and return data. Firmware must prevent transmit contention and ensure that every node releases the bus before another node responds.

📊

Data Acquisition Equipment

The ISL81487IB can connect laboratory or process-oriented data-acquisition equipment to a balanced RS-485 instrument bus. The 5 Mbps maximum data rate supports short, high-throughput links, while the 1/8-unit-load receiver permits multiple instruments to coexist with less loading than a standard receiver. For RS-422 point-to-point arrangements, the balanced differential path can provide a useful combination of speed and noise immunity. Accurate performance depends on controlled impedance, equal-length routing where appropriate, proper shielding, and termination matched to the cable and topology.

🌐

RS-422 Point-to-Point Links

The ISL81487IB supports RS-422 communication between two pieces of equipment when the system requires a balanced differential interface. Its one-driver and one-receiver organization maps directly to a full-duplex link when the two transceivers are wired as opposing transmitters and receivers. The 5 V supply and 5 Mbps data-rate capability suit legacy controller and instrument interfaces, while the 70 mV receiver hysteresis helps distinguish valid differential states amid noise. Direction signaling and unused outputs must be configured carefully when both RS-485 and RS-422 modes share a design.

🔧

Serial Port and Cable Extenders

The ISL81487IB can extend a UART-style serial connection across a balanced cable in industrial equipment, service panels, or distributed controllers. The differential driver reduces sensitivity to common-mode noise compared with a single-ended interface, and the 5 Mbps device limit supports substantially faster transfer rates than legacy serial ports commonly require. The board implementation should keep the transceiver close to the connector, provide a continuous return-path reference, and incorporate field-side surge protection when the cable leaves the enclosure.

अनुशंसित उत्पादों का सारांश

ISL81487IB Renesas Electronics उपयोग में: Industrial RS-485 Sensor Networks, Building Automation Gateways, Remote I/O Modules, Data Acquisition Equipment, RS-422 Point-to-Point Links, Serial Port and Cable Extenders ISL81487IB-T Handling variant of the bus transceiver उपयोग में: Industrial RS-485 Sensor Networks, RS-422 Point-to-Point Links ISL81487L ESD-protected family option उपयोग में: Building Automation Gateways, Serial Port and Cable Extenders ISL81487E ESD-protected family option उपयोग में: Remote I/O Modules ISL8487E ESD-protected family option उपयोग में: Data Acquisition Equipment
What is the ISL81487IB?
The ISL81487IB is a 5 V, single-channel BiCMOS transceiver for balanced RS-485 and RS-422 communication. It integrates one driver and one receiver for half-dupplex operation and supports data rates up to 5 Mbps. According to the Intersil ISL81487 datasheet, the device uses a fractional 1/8-unit-load receiver design and is packaged in an 8-pin SOIC. It is intended for industrial data links, remote I/O, and point-to-point balanced communication.
What are the key specifications of ISL81487IB?
The ISL81487IB operates from a 5 V supply, supports RS-422 and RS-485 signaling, and provides one driver with one receiver for half-duplex links. According to the Intersil ISL81487 datasheet, its maximum data rate is 5 Mbps, its receiver input presents a 1/8-unit load, and its receiver hysteresis is 70 mV. The component is offered in an 8-SOIC package with an operating temperature range of -40°C to +85°C.
What is the operating voltage of ISL81487IB?
The ISL81487IB is a 5 V-powered communications transceiver. The Intersil ISL81487 datasheet identifies the device as a 5 V, low-power RS-485/RS-422 transceiver with one transmitter and one receiver. Because this part is not specified as a regulated 3.3 V-compatible device, its logic and supply rails should be checked against the host system before substitution. Use the manufacturer datasheet for the complete operating limits and absolute maximum ratings.
How fast is the ISL81487IB RS-485 transceiver?
The ISL81487IB supports a maximum data rate of 5 Mbps. This figure comes from the Intersil ISL81487 datasheet and applies to the balanced RS-485/RS-422 driver and receiver path. Cable length, transceiver loading, connector losses, clock tolerance, and signal integrity can reduce the practical rate in an installed system. The 5 Mbps rating should therefore be treated as a device limit rather than a guaranteed end-to-end link rate.
Why does the ISL81487IB have a 1/8 unit load?
The ISL81487IB presents only a 1/8 unit load at its receiver input, allowing more receivers to share one RS-485 bus than a standard one-unit-load device would permit. According to the Intersil ISL81487 datasheet, this fractional loading is one of the family's defining characteristics. Actual bus capacity still depends on cable length, topology, termination, line biasing, and the combined loading from every transceiver and termination network.
Can ISL81487IB be used for both RS-485 and RS-422?
Yes. The ISL81487IB is designed for both RS-485 and RS-422 balanced communication, as stated in the Intersil ISL81487 datasheet. In an RS-485 network, the single driver and receiver can serve a shared half-duplex bus. For RS-422, the device can be used in point-to-point or multipoint topologies where the system architecture and signal direction support that arrangement. External direction, termination, and biasing components remain necessary.
Where can I download the ISL81487IB datasheet PDF?
The ISL81487IB datasheet can be obtained from the Renesas or Intersil documentation links listed on this page. The device documentation describes the 5 V supply, 5 Mbps data rate, 1/8-unit-load input, 70 mV hysteresis, RS-485/RS-422 operation, and 8-pin SOIC pin configuration. Use the manufacturer document for authoritative pin names, absolute maximum ratings, electrical characteristics, and application guidance before releasing a production schematic.
Where can I find the ISL81487IB pinout?
The ISL81487IB pin assignment is documented in the Intersil ISL81487 datasheet under the 8-SOIC package and pin-description information. The eight pins include the supply, ground, driver input and output, receiver input and output, and driver enable or related control functions. Use that pin-description table when assigning PCB tracks because the complete numbered diagram is not reproduced on this page. Confirm the exact orientation and pin numbering against the selected package drawing.
What is the best drop-in replacement for ISL81487IB?
The closest documented drop-in choices are the related 8-SOIC Renesas ISL81487 family members with the same RS-485/RS-422 transceiver function. ISL81487L and ISL81487E appear in the manufacturer family documentation, while ISL81487IB-T is a handling variant of the original MPN. The -T version is technically identical but should not be treated as a distinct engineering alternative. Confirm ESD protection, supply limits, enable behavior, and pin compatibility before approving any replacement.
Can ISL81487IB-T replace ISL81487IB?
Yes, ISL81487IB-T is the orderable handling variant of ISL81487IB and uses the same 8-SOIC RS-485/RS-422 transceiver configuration. The primary difference is the supplied packaging format rather than a change in the core electrical function. Confirm whether the receiving assembly requires tubes, tape-and-reel presentation, or another documented shipping format. A mechanical handling suffix does not provide a meaningful functional upgrade, so it should not be counted as a separate alternative design choice.
What is the difference between ISL81487IB and ISL81487L?
The primary documented family distinction is ESD protection: the Renesas family document identifies ISL81487L as an ESD-protected RS-485/RS-422 transceiver, while ISL81487IB is identified separately as a low-power, high-speed or slew-rate-limited family member. Both use an 8-SOIC format and address 5 V balanced communications, but the ESD rating and related protection details should be compared directly before substitution. The manufacturer family datasheet is the controlling document for those differences.
When should I choose ISL81487IB over another RS-485 transceiver?
Choose ISL81487IB when a legacy design specifically calls for a 5 V, 8-SOIC, single-driver/single-receiver half-duplex RS-485/RS-422 interface with a 1/8-unit-load receiver and a 5 Mbps device rating. It is particularly suitable for existing industrial or remote-I/O boards that need to retain an established footprint. For new designs, compare ESD protection, supply compatibility, shutdown features, fail-safe behavior, and availability before deciding whether a related or newer family member is preferable.
Is ISL81487IB suitable for industrial networks?
The ISL81487IB is suitable for many 5 V industrial communication interfaces because it supports RS-485 and RS-422, offers a 5 Mbps maximum data rate, and presents a low 1/8-unit load to the bus. Its -40°C to +85°C operating range supports typical industrial environments. Suitability still depends on isolation, surge protection, grounding, cable length, EMC requirements, and whether the end equipment requires newer ESD or fault-protection features.
Where can I buy ISL81487IB online?
Use the Request a Quote form on this page to request availability, lead time, minimum order quantity, and a formal quotation for the ISL81487IB. The component is listed as obsolete, so supply may depend on legacy inventory rather than current mass-production allocation. Request the exact MPN, required package variant, tube or tape-and-reel handling preference, quantity, and target delivery date. This preserves traceability for an obsolete communications interface.
What is the price and lead time for ISL81487IB?
Use the Request a Quote form on this page for the current ISL81487IB quotation, stock position, and production lead time. Because the manufacturer status is obsolete, price and availability can vary with remaining inventory, packaging requirement, order quantity, and quality documentation. Specify whether the assembly needs the original tube presentation or the documented -T handling variant. Request written confirmation of lifecycle status before committing the component to a new production release.

के लिए इंजीनियरिंग संदर्भ डेटा ISL81487IB — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose ISL81487IB when maintaining a legacy 5 V RS-485 or RS-422 board that specifically requires the original 8-SOIC device, including its 1/8-unit-load receiver, 70 mV hysteresis, and 5 Mbps device rating. It is particularly appropriate when an existing qualified design must remain electrically unchanged. Choose ISL81487L or ISL81487E when the same footprint and communication class are needed with explicitly documented ESD protection, after checking enable behavior and electrical limits. Consider ISL8487E for an ESD-protected related family device. The -T suffix is only a handling variant and should be selected for packaging requirements, not treated as a functional upgrade. For all choices, verify supply voltage, direction-control logic, receiver fail-safe behavior, absolute maximum ratings, and bus-node count against the manufacturer datasheet.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद ISL81487L ISL81487E ISL8487E
Brand Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics
Package 8-SOIC 8-SOIC 8-SOIC 8-SOIC
Product Type Single RS-485/RS-422 transceiver Single RS-485/RS-422 transceiver Single RS-485/RS-422 transceiver Single RS-485/RS-422 transceiver
Number of Drivers/Receivers 1/1 1/1 1/1 1/1
Supply Voltage 5 V 5 V 5 V 5 V
Maximum Data Rate 5 Mbps 5 Mbps 5 Mbps 5 Mbps
Receiver Unit Load 1/8 unit load 1/8 unit load 1/8 unit load 1/8 unit load
ESD Protection Not separately specified in the available part listing ESD protected ESD protected ESD protected
Duplex Mode Half duplex Half duplex Half duplex Half duplex

मुख्य विशेषताएँ

  • Legacy-compatible 1/8-unit-load bus interface (बनामISL81487L)
  • Original component designation for legacy production matching (बनामISL81487E)
  • Established 8-SOIC footprint with balanced interface performance (बनामISL8487E)

डिज़ाइन नोट्स

Route the RS-485 and RS-422 differential pair as a tightly coupled pair with continuous impedance and without stubs. Keep the balanced traces away from switching nodes, clock signals, and high-current return paths. Connect the transceiver ground reference close to the device and provide a low-impedance chassis or signal-ground strategy at the external connector. Differential routing improves noise immunity, but it does not compensate for poor grounding or an unsuitable cable.

Do not enable the ISL81487IB driver while another node is transmitting on the same RS-485 bus. Use a deterministic direction-control scheme and guarantee a dead time between transmit and receive operations. Place termination only at the two physical ends of the bus; excessive termination loads the line and reduces common-mode margin. Biasing should also be designed for the actual topology so that an idle bus remains in a valid differential state.

Treat the external connector as an interface boundary. Add appropriately rated surge and ESD protection close to the connector, with the protection device selected for the required voltage, current, and data-rate environment. Maintain a controlled ground connection between the protection network and transceiver. Keep field-side protection components out of the sensitive balanced-pair geometry, and verify that their capacitance does not excessively degrade edge rate or common-mode performance.

अनुपालन जानकारी

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

The available manufacturer-family documentation identifies ESD-protected variants, but explicit RoHS, REACH, lead-free, halogen-free, conflict-minerals, and AEC-Q100 declarations for the exact ISL81487IB orderable MPN were not identified.

डेटा सत्यापन तिथि: 2026-11-15 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

ISL81487IB datasheet ISL81487IB datasheet pdf ISL81487IB pinout ISL81487IB specifications ISL81487IB 8-SOIC ISL81487IB RS-485 transceiver ISL81487IB vs ISL81487L ISL81487IB equivalent ISL81487IB replacement Renesas ISL81487IB ISL81487IB price ISL81487IB stock

संबंधित कंपोनेंट्स और शब्द

Renesas Electronics Intersil ISL81487IB ISL81487L ISL81487E ISL8487E RS-485 RS-422 transceiver interface IC half-duplex balanced differential signaling 1/8 unit load 5 Mbps 70 mV hysteresis BiCMOS 8-SOIC SOIC family surface-mount package industrial communication remote I/O building automation ESD protection common-mode noise rejection
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें