ISL81487IB 5V 5Mbps RS-485/RS-422 Transceiver | Renesas
MPN: ISL81487IB ✗ انتهى عمره الإنتاجيISL81487IB نظرة عامة
An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into differential balanced signals for reliable communication over cables and noisy industrial environments. The RS-422 standard supports point-to-point, full-duplex signaling, while RS-485 allows multiple drivers and receivers on a shared half-duplex bus. The ISL81487IB belongs to the broader interface-IC hierarchy and is designed for low-power, 5 V system rails.
Key characteristics include a 1/8-unit-load receiver input, a 70 mV receiver hysteresis, operation from a 5 V supply, and a maximum data rate of 5 Mbps. Its fractional unit load permits more nodes on an RS-485 bus than a conventional one-unit-load receiver. The 8-SOIC surface-mount package also supports compact, automated PCB assembly while exposing a standard leaded footprint rather than a fine-pitch land pattern.
The BiCMOS transceiver architecture provides low-power operation for equipment that communicates over cables longer than the short reach of ordinary logic signals. Differential signaling improves common-mode noise rejection, while the low unit-load rating supports networks containing several transceivers. Because the ISL81487IB supports both RS-485 and RS-422, one device can serve industrial controllers, data-acquisition equipment, building automation, and point-to-point instrument interfaces.
Typical uses include factory-floor sensor networks, industrial control gateways, serial port extenders, and remote I/O modules. In an RS-485 installation, the transceiver is placed between a UART or microcontroller and the balanced bus. Direction control determines whether the transmitter or receiver is enabled, while termination and biasing must be designed according to the cable topology.
The primary layout consideration is keeping the balanced driver and receiver paths short, symmetrical, and physically separated from noisy switching circuits. Place termination components at the physical ends of the bus rather than beside every transceiver. Check the transceiver state during startup so that multiple drivers do not contend on the bus, and verify that the selected line baud rate remains within the device's 5 Mbps capability.
This product data combines operating characteristics, lifecycle information, package details, drop-in family alternatives, comparison parameters, and practical interface-design guidance. It is intended to accelerate component evaluation and PCB planning while making the distinctions between the original ISL81487IB and related Renesas family members explicit.
بدائل مباشرة لـ ISL81487IB — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع ISL81487IB (نفس عامل الشكل والبصمة) — يختلف في Package, Product Type.
ISL81487L
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
ISL81487E
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
ISL8487E
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
ISL81487IB المواصفات
| Product Type | Single-channel RS-485/RS-422 transceiver |
| جهد التغذية | 5 V |
| معدل البيانات | 5 Mbps |
| Number of Drivers | 1 |
| Number of Receivers | 1 |
| Duplex Mode | Half duplex |
| Receiver Unit Load | 1/8 unit load |
| Receiver Hysteresis | 70 mV |
| Supported Protocols | RS-422 and RS-485 |
| Logic Technology | BiCMOS |
| نطاق درجة حرارة التشغيل | -40°C to +85°C |
| العلبة | 8-SOIC |
| نمط التركيب | Surface mount |
| Packaging Type | Tube |
دليل تكوين أطراف ISL81487IB 8-soic
تكوين الأطراف لـ ISL81487IB (حزمة 8-soic). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ ISL81487IB.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
ISL81487IB مناسب لـ 6 التطبيقs: Industrial RS-485 Sensor Networks, Building Automation Gateways, Remote I/O Modules, Data Acquisition Equipment, RS-422 Point-to-Point Links, Serial Port and Cable Extenders.
Industrial RS-485 Sensor Networks
The ISL81487IB fits distributed sensor networks where multiple remote measurement nodes must share a balanced bus. Its 1/8-unit-load receiver minimizes the loading contributed by each node, while the 5 Mbps maximum data rate supports fast polling and update cycles. Place the transceiver between the node controller and the RS-485 pair, use a controlled driver-enable signal, and install termination only at the two physical bus ends. The -40°C to +85°C operating range is appropriate for many industrial cabinets, although surge and isolation requirements should be handled separately.
موصى به
Building Automation Gateways
The ISL81487IB is suitable for building-automation controllers that connect an embedded processor to an RS-485 floor network. Its 5 V supply aligns with many 5 V controller platforms, while the half-duplex one-driver/one-receiver arrangement supports request-and-response communication with remote modules. The 1/8-unit-load input allows several nodes to share a bus, and the 5 Mbps device rating provides ample margin for typical building-control traffic. Designers should still model cable length, common-mode range, grounding, and transient protection at the field connector.
موصى به
Remote I/O Modules
The ISL81487IB provides a compact interface between a controller and remote digital or analog I/O stations connected by an RS-485 backbone. Its 8-SOIC package is easy to route on both legacy and new controller boards, and its 1/8-unit-load receiver supports a larger node count than a one-unit-load transceiver. The single transmitter is controlled by a direction signal, allowing the same balanced pair to carry commands and return data. Firmware must prevent transmit contention and ensure that every node releases the bus before another node responds.
موصى به
Data Acquisition Equipment
The ISL81487IB can connect laboratory or process-oriented data-acquisition equipment to a balanced RS-485 instrument bus. The 5 Mbps maximum data rate supports short, high-throughput links, while the 1/8-unit-load receiver permits multiple instruments to coexist with less loading than a standard receiver. For RS-422 point-to-point arrangements, the balanced differential path can provide a useful combination of speed and noise immunity. Accurate performance depends on controlled impedance, equal-length routing where appropriate, proper shielding, and termination matched to the cable and topology.
موصى به
RS-422 Point-to-Point Links
The ISL81487IB supports RS-422 communication between two pieces of equipment when the system requires a balanced differential interface. Its one-driver and one-receiver organization maps directly to a full-duplex link when the two transceivers are wired as opposing transmitters and receivers. The 5 V supply and 5 Mbps data-rate capability suit legacy controller and instrument interfaces, while the 70 mV receiver hysteresis helps distinguish valid differential states amid noise. Direction signaling and unused outputs must be configured carefully when both RS-485 and RS-422 modes share a design.
موصى به
Serial Port and Cable Extenders
The ISL81487IB can extend a UART-style serial connection across a balanced cable in industrial equipment, service panels, or distributed controllers. The differential driver reduces sensitivity to common-mode noise compared with a single-ended interface, and the 5 Mbps device limit supports substantially faster transfer rates than legacy serial ports commonly require. The board implementation should keep the transceiver close to the connector, provide a continuous return-path reference, and incorporate field-side surge protection when the cable leaves the enclosure.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ ISL81487IB — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | ISL81487L | ISL81487E | ISL8487E |
|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Product Type | Single RS-485/RS-422 transceiver | Single RS-485/RS-422 transceiver | Single RS-485/RS-422 transceiver | Single RS-485/RS-422 transceiver |
| Number of Drivers/Receivers | 1/1 | 1/1 | 1/1 | 1/1 |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V |
| Maximum Data Rate | 5 Mbps | 5 Mbps | 5 Mbps | 5 Mbps |
| Receiver Unit Load | 1/8 unit load | 1/8 unit load | 1/8 unit load | 1/8 unit load |
| ESD Protection | Not separately specified in the available part listing | ESD protected | ESD protected | ESD protected |
| Duplex Mode | Half duplex | Half duplex | Half duplex | Half duplex |
أبرز الفروقات
- Legacy-compatible 1/8-unit-load bus interface (مقابلISL81487L)
- Original component designation for legacy production matching (مقابلISL81487E)
- Established 8-SOIC footprint with balanced interface performance (مقابلISL8487E)
ملاحظات التصميم
Route the RS-485 and RS-422 differential pair as a tightly coupled pair with continuous impedance and without stubs. Keep the balanced traces away from switching nodes, clock signals, and high-current return paths. Connect the transceiver ground reference close to the device and provide a low-impedance chassis or signal-ground strategy at the external connector. Differential routing improves noise immunity, but it does not compensate for poor grounding or an unsuitable cable.
Do not enable the ISL81487IB driver while another node is transmitting on the same RS-485 bus. Use a deterministic direction-control scheme and guarantee a dead time between transmit and receive operations. Place termination only at the two physical ends of the bus; excessive termination loads the line and reduces common-mode margin. Biasing should also be designed for the actual topology so that an idle bus remains in a valid differential state.
Treat the external connector as an interface boundary. Add appropriately rated surge and ESD protection close to the connector, with the protection device selected for the required voltage, current, and data-rate environment. Maintain a controlled ground connection between the protection network and transceiver. Keep field-side protection components out of the sensitive balanced-pair geometry, and verify that their capacitance does not excessively degrade edge rate or common-mode performance.
معلومات الامتثال
The available manufacturer-family documentation identifies ESD-protected variants, but explicit RoHS, REACH, lead-free, halogen-free, conflict-minerals, and AEC-Q100 declarations for the exact ISL81487IB orderable MPN were not identified.