ISL83385CA - Single RS-232 Transceiver | Harris Corporation
MPN: ISL83385CA ✗ जीवन की समाप्तिISL83385CA अवलोकन
The ISL83385CA is associated with the 20-SSOP package family according to closely related manufacturer listing data for ISL83385ECA. The package is a surface-mount SOIC-family implementation with leads on two opposing sides, making it practical for compact industrial, communications, and embedded-control equipment. Exact pin assignments, electrical limits, and charge-pump details should be confirmed in the manufacturer datasheet before a new layout is released.
An RS-232 transceiver combines functions that are normally separated in older interface designs. The transmitter converts CMOS/TTL-level inputs into the bipolar voltage range used by RS-232, while the receiver provides noise-tolerant logic-level output. Combining both directions in one IC reduces board area and component count, but it does not eliminate the need for correct interface protection, grounding, cable routing, and logic-level compatibility checks.
The most relevant application areas are point-to-point serial links, industrial control panels, test equipment, data acquisition systems, and embedded systems that communicate with legacy RS-232 peripherals. A designer should pay particular attention to the number of data and control lines, the available package footprint, the required logic thresholds, and the maximum data rate. Because the target package and pin functions are not fully stated in the available manufacturer listing text, the footprint and signal assignments should be checked against the official ISL83385CA documentation.
This page combines the target part identity with a practical RS-232 design perspective, including selection criteria, interface considerations, and a comparison framework for evaluating compatible RS-232 transceiver options. The specific electrical ratings and lifecycle details should be confirmed against the current Harris Corporation product documentation before procurement or PCB release.
के लिए ड्रॉप-इन विकल्प ISL83385CA — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस उत्पाद के लिए कोई drop-in alternatives उपलब्ध नहीं।
विकल्प अनुरोध करेंISL83385CA विशेषताएं
| Product Type | RS-232 transmitter/receiver interface IC |
| Channel Count | 1 channel |
| Directional Capability | Bidirectional transmitter and receiver |
| Interface Category | RS-232 |
| Logic Interface | CMOS/TTL-level digital signaling |
| माउंटिंग प्रकार | Surface mount |
| RoHS स्थिति | unknown |
| REACH Status | unknown |
| Automotive Qualification | unknown |
ISL83385CA standard पिन कॉन्फ़िगरेशन गाइड
ISL83385CA (standard पैकेज) के लिए पिन कॉन्फ़िगरेशन। पिन नंबरिंग, फ़ंक्शन और कनेक्शन आरेख निर्माता डेटाशीट में परिभाषित हैं। सटीक फुटप्रिंट और सोल्डरिंग दिशानिर्देशों के लिए इसे देखें।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: ISL83385CA.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
ISL83385CA के लिए उपयुक्त है 6 अनुप्रयोगs: Industrial Controller RS-232 Port, Test and Measurement Console, Data Acquisition Interface, Service and Configuration Port, Communications Equipment, Embedded Control Systems.
Industrial Controller RS-232 Port
The ISL83385CA fits a point-to-point industrial controller that must communicate with a legacy RS-232 peripheral. Combining one transmitter and one receiver in a single interface IC reduces the number of discrete interface components and simplifies firmware ownership of the UART connection. The design should confirm the device's supply voltage, maximum data rate, logic thresholds, and exact package footprint against the controller requirements. RS-232 is not a balanced differential standard, so grounding, cable routing, connector selection, and transient protection remain important even when the signal path is short. Use the manufacturer datasheet to assign every transceiver pin and to determine whether charge-pump capacitors or other external components are required.
Test and Measurement Console
The ISL83385CA can provide a compact RS-232 link between a test instrument or service console and a host controller. Its single bidirectional channel suits equipment that exchanges commands and measurements through one serial port without needing multiple independently selectable receivers. Designers should verify the supported data rate before selecting it for automated laboratory control, then account for the connector's unbalanced signaling and susceptibility to industrial noise. A firm ground reference, short organized cable, and appropriate protection network improve reliability. The exact pin arrangement and external capacitor requirements should follow the manufacturer documentation rather than a generic RS-232 reference design.
Data Acquisition Interface
The ISL83385CA is suitable for a data-acquisition unit that must translate a controller UART into an RS-232 connection for an external instrument or legacy data source. Integrating the driver and receiver in one IC reduces board area and avoids coordinating separate enable controls. The implementation must preserve signal levels expected by both sides of the interface, observe the device's maximum data rate, and confirm its operating-temperature range for the measurement environment. Because RS-232 uses a single-ended signal referenced to ground, a common ground and controlled cable route are required. Review the exact pin and package information in the manufacturer datasheet before laying out the acquisition board.
Service and Configuration Port
The ISL83385CA fits embedded equipment that exposes a service port for configuration, firmware loading, or diagnostic commands. One transmitter and one receiver provide the required bidirectional command path while keeping the interface compact. Firmware should define a robust framing and timeout protocol because the physical RS-232 link alone provides no handshaking or error recovery. Hardware designers should use the exact ordering-code pinout, provide the specified bypass and charge-pump components, and add connector-side protection where cables can be exposed to user contact. The part is a strong fit when a legacy host computer is the intended counterpart.
Communications Equipment
The ISL83385CA can be used in communications equipment that bridges a modern UART controller to a single RS-232 port. This arrangement is common in legacy network-management equipment, terminal adapters, and diagnostic modules where the RS-232 endpoint remains established but board area is constrained. The integration saves the footprint of separate transmit and receive interface devices, provided the package and pinout are verified correctly. Engineers should examine receiver noise margin, transmitter slew behavior, grounding, and any requirement for an external modem-control or hardware-handshake path. A multi-channel transceiver should be selected instead when several ports or switchable routes are required.
Embedded Control Systems
The ISL83385CA provides a practical RS-232 interface for embedded control systems that must connect a microcontroller or programmable controller to legacy equipment. Its integrated driver and receiver simplify the hardware boundary between the controller and the RS-232 connector, while the one-channel topology avoids unnecessary multiplexing. Firmware must still implement the UART protocol and line-level timing expected by the connected device. Layout should keep high-level switching and connector transients away from sensitive control circuitry, and the system must confirm the package pin count and land pattern before release. Use the manufacturer documentation to validate supply, bypass, capacitor, and temperature requirements.
के लिए इंजीनियरिंग संदर्भ डेटा ISL83385CA — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
डिज़ाइन नोट्स
Verify the exact ISL83385CA footprint against the suffix-specific manufacturer drawing before routing. The target listing does not expose a complete package designation, while a related ISL83385ECA listing identifies a 20-SSOP package. Confirm body width, lead pitch, lead span, and pin numbering rather than assuming that all family suffixes use the same land pattern. Place the required bypass and charge-pump components close to their associated pins using the shortest possible traces.
Do not approve a replacement based only on the ISL83385 family name or package family. Compare the exact supply pins, transmitter and receiver pins, charge-pump terminals, shutdown behavior, and exposed-pad requirements in each manufacturer datasheet. A device with the same body outline can still be non-pin-compatible if its pin numbering, thermal pad, or electrical limits differ. Record the approved alternate part number against the specific schematic and board revision.
Treat the RS-232 connector side as a potentially noisy single-ended interface. Route it away from clocks, sensor inputs, and sensitive analog traces; use a stable common ground between connected equipment; and place connector-side protection close to the entry point. Confirm the receiver's noise tolerance and the transmitter's supported slew behavior in the datasheet. Avoid long unprotected traces or unnecessary stubs between the transceiver and connector.
अनुपालन जानकारी
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statements appear in the verified target records. Confirm current compliance documentation with Harris Corporation or the authorized product-continuity organization.