Renesas Electronics

ISL83485IP - 3.3V 10Mbps Half-Duplex RS-485/RS-422 | Renesas

MPN: ISL83485IP ✓ सक्रिय
3.3 V Vdss RS-485 and RS-422 Rds(on) 8-pin PDIP Package
न्यूनतम ऑर्डर मात्रा: 1 |

ISL83485IP अवलोकन

The Renesas Electronics ISL83485IP is a 3.3 V, single-channel, half-duplex RS-485/RS-422 transceiver operating at up to 10 Mbps in an 8-pin PDIP package. It combines one driver and one receiver in a BiCMOS device designed for balanced industrial communication links. Its 3.3 V supply supports low-voltage systems that need high-speed differential signaling without requiring a 5 V transceiver.

An RS-485/RS-422 transceiver is an interface IC that converts logic-level transmit and receive signals into balanced differential signals and back again. It belongs to the communication-interface hierarchy: transceiver > line driver and receiver > RS-485/RS-422 interface IC > semiconductor. This makes the ISL83485IP suitable for industrial control, data acquisition, instrumentation, and equipment interconnects where signal integrity and noise immunity are important.

Key device characteristics include a 3.3 V power supply, half-duplex operation, a maximum data rate of 10 Mbps, and support for both RS-485 and RS-422 standards. The device also uses a low-power BiCMOS implementation. Half-duplex operation means the transmitter and receiver share the same bus pair, so the design must control driver enable and receiver enable states to avoid contention on the network.

The receiver provides a differential input stage for noisy industrial environments, while the balanced bus reduces susceptibility to common-mode noise compared with a single-ended interface. RS-485 operation supports multidrop bus arrangements subject to the applicable termination and biasing rules, whereas RS-422 typically uses a point-to-point or one-driver topology. The exact driver-enable, receiver-enable, and fault-recovery behavior should be confirmed from the manufacturer datasheet before final schematic sign-off.

Typical uses include PLC-to-sensor links, motor-control diagnostics, industrial test equipment, factory monitoring nodes, and embedded systems communicating with remote modules. The 10 Mbps capability is useful for burst-oriented protocols, while the 3.3 V supply simplifies interfacing with modern low-voltage controllers.

For PCB implementation, keep the transceiver and any termination components close to the connector to minimize unbalanced stub length. Use a controlled-impedance differential pair for the balanced bus, provide a solid ground reference, and place the transceiver supply bypass capacitor directly beside its power pin. Avoid long point-to-point stubs because they can degrade signal integrity at the supported 10 Mbps data rate.

This page combines manufacturer specifications, verified distributor availability information, package details, replacement guidance, and application-oriented design notes. It is intended to help engineers evaluate the ISL83485IP against same-package alternatives and plan a robust RS-485 or RS-422 interface implementation.

के लिए ड्रॉप-इन विकल्प ISL83485IP — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

इस सीरीज़ के वेरिएंट

समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं ISL83485IP (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Package, Product Type, Maximum Data Rate, Transceiver Configuration, Mounting Type.

Renesas Electronics
Package: 8-SOIC (IB) 3.9 mm
Mounting Type: Surface Mount
इसके साथ तुलना करें ISL83485IP →
Renesas Electronics
Package: 8-pin PDIP (8-PDIP)
Maximum Data Rate: 250 kbps
Transceiver Configuration: 1 transmitter and 1 receiver
इसके साथ तुलना करें ISL83485IP →
Renesas Electronics
Product Type: RS-485/RS-422 transceiver IC
इसके साथ तुलना करें ISL83485IP →
Renesas Electronics
Product Type: 1/1 RS-485/RS-422 transceiver
इसके साथ तुलना करें ISL83485IP →
MaxLinear
Package: 8-PDIP
Product Type: RS-485/RS-422 half-duplex transceiver
Maximum Data Rate: 5000 kbps
इसके साथ तुलना करें ISL83485IP →

ISL83485IBZ-T

✅ ड्रॉप-इन
Renesas Electronics
📦 8-pin PDIP
Transceiver · 1/1 · Half · RS-422, RS-485 · 10 Mbps · 3.3 V · 3.0 V to 3.6 V · 1/8 unit-load (up to 256 nodes)

कीमत के लिए संपर्क करें

डेटाशीट देखें →

SP485ES-L

✅ ड्रॉप-इन
MaxLinear
📦 8-pin PDIP
RS-485/RS-422 half-duplex transceiver · 1/1 transceiver · 1 driver · 1 receiver · Half duplex · RS-485 and RS-422 · 5000 kbps · BiCMOS

कीमत के लिए संपर्क करें

डेटाशीट देखें →

ISL83483IP

✅ ड्रॉप-इन
📦 8-pin PDIP
Same ISL8348x family in the 8-pin PDIP configuration, but the specific speed-versus-slew-rate profile and enable details differ; verify data-rate and pin-function equivalence against the family datasheet

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

ISL83488IP

✅ ड्रॉप-इन
Renesas Electronics
📦 8-pin PDIP
3.3 V · 250 kbps · RS-485 and RS-422 · Full duplex · 1 transmitter and 1 receiver · BiCMOS · Slew-rate limited · 8-pin PDIP (8-PDIP)

कीमत के लिए संपर्क करें

डेटाशीट देखें →

ISL83490IP

✅ ड्रॉप-इन
Renesas Electronics
📦 8-pin PDIP
RS-485/RS-422 transceiver IC · 1 driver · 1 receiver · Full duplex · RS-485 and RS-422 · 3 V to 3.6 V · 3.3 V · Low power

कीमत के लिए संपर्क करें

डेटाशीट देखें →

ISL83491IP

✅ ड्रॉप-इन
Renesas Electronics
📦 8-pin PDIP
1/1 RS-485/RS-422 transceiver · 3 V to 3.6 V · 3.3 V · RS-485 and RS-422 · 1 driver · 1 receiver · BiCMOS · High-speed or slew-rate-limited

कीमत के लिए संपर्क करें

डेटाशीट देखें →

ISL83485IP विशेषताएं

Product Type RS-485/RS-422 transceiver
Transceiver Configuration 1 driver / 1 receiver
Duplex Mode Half duplex
सप्लाई वोल्टेज 3.3 V
Maximum Data Rate 10 Mbps
Supported Standards RS-485 and RS-422
Process Technology BiCMOS
Power Consumption Profile Low power
Signal Type Balanced differential
पैकेज 8-pin PDIP
माउंटिंग प्रकार Through-hole

ISL83485IP पिन कॉन्फ़िगरेशन

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
पिन 1 RO — Receiver output
पिन 2 RE — Receiver enable, active-low control
पिन 3 DE — Driver enable, active-high control
पिन 4 DI — Driver input
पिन 5 GND — Ground
पिन 6 Y — Non-inverting differential bus output and receiver input
पिन 7 Z — Inverting differential bus output and receiver input
पिन 8 VCC — Positive supply

सामान्य अनुप्रयोग

ISL83485IP के लिए उपयुक्त है 6 अनुप्रयोगs: Industrial PLC and Sensor Bus, Factory Automation Data Acquisition, Motor-Control Diagnostic Interface, Instrumentation and Test Equipment, Embedded Control Module Communication, Building and Energy Monitoring Nodes.

🏭

Industrial PLC and Sensor Bus

The ISL83485IP fits 3.3 V PLC and sensor nodes that communicate over a noisy balanced bus. Its one-driver/one-receiver half-duplex arrangement supports shared RS-485 wiring, while the 10 Mbps rating accommodates burst transfers and diagnostic traffic. Place termination at the physical ends of the bus and bias the receiver only once for a multidrop network. Because the half-duplex interface shares the driver and receiver bus pins, firmware must enforce dead time around direction changes so the local transmitter never drives against an active remote node.

📡

Factory Automation Data Acquisition

The Renesas ISL83485IP can connect low-voltage controller boards to remote instrumentation over RS-422 or RS-485. A 3.3 V supply matches modern processors directly, and differential signaling helps reject common-mode noise generated by relays, motor drives, and switching power supplies. At rates up to 10 Mbps, short point-to-point links can carry synchronized measurements or configuration frames efficiently. Use a twisted, balanced pair with identical routing geometry, terminate the receiver at the far end, and keep the transceiver close to the cable entry to reduce reflections and radiated emissions.

⚡

Motor-Control Diagnostic Interface

The ISL83485IP is useful for carrying position, fault, and configuration information between a motor controller and a supervisory controller. Its balanced differential bus is preferable to a single-ended link in an enclosure containing power-switching stages. The half-duplex 10 Mbps capability supports high refresh rates, but practical field-bus implementations must respect cable length, node count, termination, and grounding rules. Use galvanic isolation when the motor and controller grounds cannot safely be bonded, and select external surge protection based on the installation environment and required immunity level.

🔧

Instrumentation and Test Equipment

The ISL83485IP supports control and measurement systems that require a compact, low-power balanced link between an instrument and a computer or fixture. The 3.3 V operation reduces supply complexity, while the 10 Mbps rate permits short, high-throughput command sequences. A one-driver/one-receiver arrangement can operate as RS-422 for a dedicated point-to-point connection or as RS-485 in a multidrop network. Place the input and output protection close to the connector, use a solid reference plane, and validate eye quality or receiver margins with the intended cable before production.

🧩

Embedded Control Module Communication

The ISL83485IP lets a 3.3 V embedded processor connect to a remote sensor head, actuator controller, or service interface without a separate 5 V transceiver rail. Its low-power BiCMOS implementation is aligned with compact control modules, and the 10 Mbps limit is more than adequate for status polling and short configuration packets. The critical design task is correct half-duplex control. Use the device's receiver-enable and driver-enable pins so the bus changes direction cleanly, and add a receive timeout that returns the interface to the safe state if the remote node stops responding.

🏠

Building and Energy Monitoring Nodes

The ISL83485IP can connect distributed energy-monitoring equipment where sensors and controllers communicate over a wired RS-485 segment. Balanced signaling is useful near switching relays and dimming equipment because it reduces susceptibility to conducted and radiated noise. The transceiver's 3.3 V supply suits modern monitoring nodes, and its 10 Mbps maximum rate permits frequent status aggregation on short bus segments. Follow the bus topology specified for the selected standard, avoid star routing, use a single termination pair at the two physical ends, and consider galvanic isolation at long cable spans or across different ground-potential zones.

What is the ISL83485IP?
The ISL83485IP is a Renesas Electronics 3.3 V, half-duplex RS-485/RS-422 transceiver rated for data rates up to 10 Mbps. It integrates one driver and one receiver in an 8-pin PDIP package and uses a BiCMOS process. According to the Renesas ISL83485 product page, the device is intended for low-power balanced communication systems that require both RS-485 and RS-422 operation.
What is the maximum data rate of the ISL83485IP?
The ISL83485IP supports a maximum data rate of 10 Mbps. This rating applies to its 3.3 V half-duplex driver and receiver functions for balanced RS-485 or RS-422 links. Renesas describes the ISL83485 family as a high-speed or slew-rate-limited transceiver, so the installed board configuration, cable length, terminations, and receiver-enable timing must also support the intended operating rate.
What is the supply voltage of the ISL83485IP?
The ISL83485IP operates from a 3.3 V supply. This low supply voltage allows the transceiver to connect directly to 3.3 V controllers and field-programmable gate arrays in compact industrial equipment. Confirm the permitted supply tolerance and the bypass-capacitor values in the Renesas manufacturer datasheet before releasing the schematic, particularly when the device is powered during hot-plug or brownout conditions.
Is the ISL83485IP half duplex or full duplex?
The ISL83485IP is a half-duplex transceiver. Its driver and receiver share one balanced bus pair, so only one direction of communication is active at a time. The design must sequence driver-enable and receiver-enable controls to prevent the driver from fighting an external transmitter during reception. Use the manufacturer timing information to establish the transition interval around direction changes.
Which package does the ISL83485IP use?
The ISL83485IP is packaged in an 8-pin PDIP through-hole package. The Renesas ISL83485 family also includes surface-mount ordering variants, but the IP suffix identifies the PDIP configuration. Because a surface-mount counterpart uses a different footprint, it is not a board-level drop-in replacement unless the PCB is redesigned. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks.
Where can I download the ISL83485IP datasheet PDF?
The Renesas ISL83485 product page provides the official device documentation and links to the family datasheet. The manufacturer product page is the preferred source for the ISL83485IP PDF because it covers the complete transceiver family, electrical characteristics, and package drawings. Search the Renesas product page for ISL83485 and select the datasheet document rather than relying on an unverified mirror.
Where can I find the ISL83485IP pinout?
The ISL83485IP pin assignment is shown in the Renesas manufacturer datasheet, which identifies the driver-input, receiver-output, enable-control, ground, power, and differential bus connections for the 8-pin PDIP. Use that pin-description table to confirm every net, because enable polarity and bus-side labels must match the exact device configuration. The Renesas ISL83485 product page provides access to the official datasheet.
What is the best drop-in replacement for the ISL83485IP?
The closest same-package replacement must use an 8-pin PDIP footprint and preserve the 3.3 V supply, half-duplex control scheme, driver/receiver pin functions, and RS-485/RS-422 electrical behavior. The SP485ES-L is an identified 8-pin PDIP, half-duplex, 1-driver/1-receiver alternative, but its 4.75 V to 5.25 V supply differs from the 3.3 V ISL83485IP. Treat it as a candidate for circuit review, not an automatic substitution.
Can the SP485ES-L replace the ISL83485IP?
The SP485ES-L is not a direct 3.3 V drop-in substitute for the ISL83485IP because it is identified as a 4.75 V to 5.25 V half-duplex transceiver in an 8-pin PDIP package. Although the package and transceiver configuration are similar, the supply range is different and the device must also satisfy the same enable, bus, receiver-output, and logic-level requirements. Review the complete datasheet and test the revised rail before production release.
When should I choose the ISL83485IP over a 5 V RS-485 transceiver?
Choose the ISL83485IP when the system operates from a 3.3 V rail and requires a half-duplex balanced link at up to 10 Mbps. Its 3.3 V supply can simplify connections to low-voltage digital controllers and reduce the need for level translation. A 5 V transceiver may be preferable when only a 5 V rail exists, when its driver strength better matches the cable, or when its fault-recovery behavior satisfies the required network specification.
Is the ISL83485IP suitable for industrial equipment?
The ISL83485IP is suitable for many industrial balanced-communication links because it supports RS-485 and RS-422 at up to 10 Mbps from a 3.3 V supply. Its differential signaling improves noise immunity in environments containing motors, switching supplies, and long cables. Industrial suitability must still be evaluated against the required temperature range, ESD level, isolation, surge immunity, and regulatory expectations for the finished equipment.
Where can I buy the ISL83485IP online?
The ISL83485IP is listed by authorized electronics suppliers and is available for quotation through the Request a Quote form on this page. The listing identifies an 8-pin PDIP Renesas transceiver, while current stock and lead time should be confirmed during sourcing. Submit the exact MPN, required quantity, and target date on the quote form so the order can be matched without package or suffix substitutions.
What is the price of the ISL83485IP?
Current unit pricing for the ISL83485IP should be obtained through the Request a Quote form on this page because distributor inventory levels, quantities, and currency can change rapidly. The quote form should be submitted with the exact 8-pin PDIP MPN and the required production quantity. Avoid substituting the related surface-mount ordering variants, since they use a different PCB footprint even though they belong to the same transceiver family.
What is the lead time for the ISL83485IP?
Request the current ISL83485IP lead time using the Request a Quote form on this page. Lead time depends on manufacturer inventory, distributor stock, order quantity, and the chosen delivery terms. Include the planned production date and annual usage so sourcing can identify whether the 8-pin PDIP configuration is stocked or requires a factory allocation. Always order by the exact ISL83485IP suffix.
Is the ISL83485IP in stock?
The ISL83485IP is shown as available for sourcing, but the exact quantity should be confirmed through the Request a Quote form on this page. Availability can vary by package suffix and order volume, so do not assume that a listing for a related SOIC ordering code guarantees stock of the PDIP version. State the required quantity and delivery date on the quote request.
What are the key specifications of the ISL83485IP that engineers should know?
The core ISL83485IP specifications are a 3.3 V supply, half-duplex operation, one driver and one receiver, support for RS-485 and RS-422, a maximum data rate of 10 Mbps, and an 8-pin PDIP package. According to the Renesas product page, the device uses a low-power BiCMOS implementation. These figures define the core interface, while cable length, termination, protection, and enable timing determine practical network performance.

के लिए इंजीनियरिंग संदर्भ डेटा ISL83485IP — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose the ISL83485IP when a system requires a 3.3 V, half-duplex balanced link at up to 10 Mbps and the 8-pin PDIP footprint is already present on the PCB. It is a strong choice for low-voltage embedded controllers, PLC nodes, instrumentation, and industrial monitoring systems where the transceiver must support both RS-485 and RS-422. The SP485ES-L is a functionally similar DIP-8 alternative, but its 4.75 V to 5.25 V supply makes it more suitable for a 5 V design or a board-level power revision. Related ISL8348x ordering codes can reduce qualification effort within the Renesas family, but the exact 83, 88, 90, and 91 variants differ in speed or slew-rate options. Before replacing any candidate, verify supply limits, bus and logic pin assignments, driver-enable polarity, receiver-output behavior, fail-safe state, package drawings, and the required operating temperature range.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद ISL83485IBZ-T SP485ES-L ISL83483IP ISL83488IP ISL83490IP ISL83491IP
Package 8-pin PDIP 8-pin PDIP configuration listed as a related family ordering code; board footprint must be revalidated 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP
Brand Renesas Electronics Renesas Electronics Exar Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics
Supply Voltage 3.3 V 3.3 V 4.75 V to 5.25 V 3.3 V family configuration 3.3 V family configuration 3.3 V family configuration 3.3 V family configuration
Supported Standards RS-485 and RS-422 RS-485 and RS-422 RS-485 and RS-422 RS-485 and RS-422 family option RS-485 and RS-422 family option RS-485 and RS-422 family option RS-485 and RS-422 family option

मुख्य विशेषताएँ

  • Direct 3.3 V operation supports modern low-voltage hosts (बनामSP485ES-L)
  • Ten-megabit half-duplex operation in a single IC (बनामSP485ES-L)
  • Compatible Renesas family sourcing path (बनामISL83483IP)

डिज़ाइन नोट्स

Route the balanced bus as a tightly coupled differential pair with the same geometry on both conductors, and keep the transceiver close to the connector. Place the supply bypass capacitor directly beside VCC and connect the ground return using a low-impedance path. Avoid long stubs, vias, and test pads that create impedance discontinuities. For RS-485 multidrop networks, install termination only at the two physical cable ends and avoid placing termination on every node.

Half-duplex direction control must include a guaranteed dead interval between turning the driver off and enabling the receiver. Firmware delays alone may be insufficient when the bus must handle multiple baud rates or variable frame lengths. Use the manufacturer's timing characteristics to set the maximum turnaround allowance, add a receive timeout, and verify the completed board with the longest intended cable and the highest expected loading rather than relying only on a short bench connection.

Do not treat the 3.3 V ISL83485IP as interchangeable with a 5 V RS-485 transceiver without reviewing the complete supply, logic-threshold, enable, bus-pin, and receiver-output requirements. The SP485ES-L, for example, is identified as a 4.75 V to 5.25 V DIP-8 device with otherwise similar transceiver characteristics. A matching package count is not sufficient proof of drop-in compatibility, particularly when the transceiver's bus-side pin arrangement or control polarity differs.

Keep external protection components close to the cable connector and connect their return path to the board's reference plane. When adding surge or ESD protection, account for its capacitance, which can reduce the usable bandwidth or disturb differential balance at 10 Mbps. Use a matched protection device on Y and Z, maintain symmetric placement, and verify edge quality at the connector. In electrically noisy industrial systems, isolation may be more effective than escalating protection levels on the transceiver itself.

अनुपालन जानकारी

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

The ISL83485IP is an industrial RS-485/RS-422 interface IC and is not an automotive-qualified AEC-Q100 device. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations should be confirmed on the current Renesas product documentation or supplier declaration before environmental-compliance release.

डेटा सत्यापन तिथि: 2026-11-15 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

ISL83485IP datasheet ISL83485IP pinout ISL83485IP datasheet pdf Renesas ISL83485IP ISL83485IP 8-pin PDIP ISL83485IP 3.3V transceiver ISL83485IP 10Mbps RS-485 ISL83485IP RS-422 application ISL83485IP vs SP485ES-L ISL83485IP equivalent ISL83485IP replacement ISL83485IP price ISL83485IP stock where to buy ISL83485IP

संबंधित कंपोनेंट्स और शब्द

Renesas Electronics ISL83485IP ISL83485 ISL83485IBZ-T SP485ES-L ISL83483IP ISL83488IP ISL83490IP ISL83491IP RS-485 RS-422 half-duplex transceiver line driver line receiver balanced differential signaling BiCMOS 3.3 V transceiver 10 Mbps data rate 8-pin PDIP through-hole package industrial communication RS-485 multidrop bus RS-422 point-to-point link driver enable receiver enable
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें