LM258AYDT - Dual 1.1MHz Low-Power Op Amp | STMicroelectronics
MPN: LM258AYDT ✓ सक्रियLM258AYDT अवलोकन
An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between signals applied to its inverting and non-inverting inputs. The LM258AYDT belongs to the operational-amplifier hierarchy, combining low-power operation, dual-channel integration, and an 8-pin SOIC footprint in a component intended for cost-sensitive analog signal-chain designs.
Key characteristics include two amplifier circuits in one package, a 1.1 MHz gain-bandwidth product, and low-power operation. The integrated dual configuration reduces external component count and PCB area when a design requires two matched-function amplifier channels. Its standard SOIC-8 package also supports conventional surface-mount assembly and hand-soldering or automated placement.
The amplifier architecture is suited to closed-loop configurations in which feedback defines the gain and bandwidth. Designers must maintain the input common-mode voltage and output-voltage limits published by STMicroelectronics, because operation outside those limits can impair signal integrity or reduce reliability. Input and output stability should be evaluated using the manufacturer’s recommended source, load, and bypass-capacitor arrangements.
Typical uses include industrial sensor interfaces, audio preamplifier stages, loop filters, sensor-conditioning channels, and low-frequency control or measurement circuits. Two amplifiers can implement differential, instrumentation-style signal handling, cascaded gain stages, active filters, or independent channels where board area is constrained.
For PCB implementation, place decoupling capacitors close to the supply pins and route sensitive input and feedback paths away from high-current switching nodes. Check input bias-current effects, output swing, stability with the selected load, and the operating-temperature range before committing the design to production.
This product page combines package, technical, replacement, and application guidance with practical design considerations. It also identifies where pinout, compliance, and detailed electrical values must be confirmed against the manufacturer’s LM258AYDT datasheet before layout release or component substitution.
के लिए ड्रॉप-इन विकल्प LM258AYDT — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस सीरीज़ के वेरिएंट
समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं LM258AYDT (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Package, Slew Rate, Amplifier Type, Gain-Bandwidth Product, Product Type.
LM258AYD
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
LM258DT
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →TSH22IDT
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
TSB7192IDT
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
LM258AYDT Maximum Ratings और Electrical Characteristics
| Product Type | Dual general-purpose operational amplifier |
| Number of Amplifier Circuits | 2 circuits |
| Gain-Bandwidth Product | 1.1 MHz |
| पैकेज | 8-SOIC |
| Package Width | 3.90 mm |
| Lead Pitch | 0.154 inch |
| माउंटिंग प्रकार | Surface mount |
| Power Class | Low-power dual operational amplifier |
LM258AYDT 3.90 mm पिन कॉन्फ़िगरेशन गाइड
LM258AYDT (3.90 mm पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस एनालॉग कंपोनेंट में इनपुट, आउटपुट और पावर सप्लाई पिन हैं। ऑफ़सेट नल, कम्पनसेशन और एनेबल पिन कॉन्फ़िगरेशन के लिए निर्माता डेटाशीट देखें। सिग्नल कंडीशनिंग और एम्प्लीफ़ायर सर्किट के लिए आदर्श।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: LM258AYDT.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
LM258AYDT के लिए उपयुक्त है 6 अनुप्रयोगs: Industrial Sensor Signal Conditioning, Audio Preamplifier Stages, Active Loop Filters, Power Supply Current Monitoring, Portable Instrumentation, Control Loop Amplification.
Industrial Sensor Signal Conditioning
The LM258AYDT suits low-frequency industrial sensor interfaces because it combines two amplifier channels with a 1.1 MHz gain-bandwidth product in an 8-SOIC package. One channel can amplify the sensor output while the other provides active filtering, buffering, or an instrumentation-style feedback path. Its low-power dual architecture reduces the number of analog packages and board area compared with two separate single amplifiers. Designers should establish the sensor excitation level, expected common-mode voltage, source impedance, and required noise bandwidth before selecting resistor and capacitor values. Protection, filtering, and grounding remain important when the input originates from long cables or noisy process equipment.
अनुशंसित
Audio Preamplifier Stages
The LM258AYDT can implement low-frequency audio preamplification, equalization, or active filtering when the signal bandwidth remains below its 1.1 MHz gain-bandwidth product. Its two amplifier channels can be assigned to separate stages or arranged as a non-inverting amplifier followed by an output buffer. This dual arrangement can simplify the layout of small audio modules while reducing package count. The amplifier is intended for general-purpose operation rather than low-noise headphone drive, so the design should verify input-referred noise, output swing, distortion, and load compatibility against the manufacturer’s electrical characteristics. Bypass capacitors and feedback traces should be positioned to avoid adding instability or audible channel-to-channel coupling.
अनुशंसित
Active Loop Filters
The LM258AYDT is well suited to implementing active low-pass, high-pass, or band-pass networks in measurement and control circuits. Two independent amplifiers permit cascaded stages, a first-order filter followed by a buffer, or an integrated multiple-feedback topology. The 1.1 MHz gain-bandwidth product provides useful headroom for filters centered well below the megahertz range, although actual corner frequency and phase margin depend on the chosen topology. Resistor tolerances, capacitor tolerances, amplifier input bias current, and output loading must be included in tolerance analysis. Check the manufacturer’s recommended operating region and use PCB layouts that keep sensitive summing nodes compact and well separated from switching-current paths.
अनुशंसित
Power Supply Current Monitoring
The LM258AYDT can monitor a voltage-derived current signal in a low-frequency power-control system by amplifying the voltage across a sense resistor and filtering the result before an ADC input. The dual-channel configuration allows one amplifier to amplify the sense signal while the other buffers or actively filters it. Because the device has a 1.1 MHz gain-bandwidth product, it is best aligned with slowly changing current measurements rather than high-bandwidth power-converter ripple analysis. The sense-resistor value must balance signal amplitude against power loss, while the amplifier input must remain within its common-mode and supply limits. Layout should use Kelvin-style sensing where practical so copper drops do not distort the measurement.
अनुशंसित
Portable Instrumentation
The LM258AYDT supports compact, battery-operated instrumentation because it provides two amplifier functions in one low-power 8-SOIC package. A portable front end can use one channel for transducer excitation and the other for measurement amplification, or use the channels for differential sensing and output buffering. The package’s small footprint supports board-space reduction, but the actual battery-life benefit depends on the selected feedback network, load, operating voltage, and system duty cycle. Designers should verify supply-current behavior over the complete input range and confirm that the input signal remains within the published common-mode limits. Local decoupling and controlled grounding are particularly important when the device operates alongside switching converters.
अनुशंसित
Control Loop Amplification
The LM258AYDT can amplify error signals in low-bandwidth feedback-control circuits such as temperature, position, or light-intensity control. One channel may compare and amplify a setpoint error, while the second channel drives a feedback network or provides an additional control stage. Its 1.1 MHz gain-bandwidth product is suitable for many slow closed-loop systems, while the low-power dual format reduces analog component count. Compensation must be based on the actual plant impedance, crossover frequency, sensor lag, and load rather than nominal gain alone. Check output-current capability, slew rate, saturation recovery, and common-mode range for the selected operating point to avoid instability or delayed system response.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा LM258AYDT — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | LM258AYD | LM258DT | TSH22IDT | TSB7192IDT |
|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Amplifier Channels | 2 circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits |
| Product Classification | Standard general-purpose amplifier | General-purpose dual operational amplifier | General-purpose dual operational amplifier | Dual operational amplifier | Dual operational amplifier |
| Drop-In Relationship | Original device | Same-family candidate with consistent terminals and package | Same-family SO8 candidate | Expected pin-compatible SO8 candidate | Expected pin-compatible SO8 candidate |
मुख्य विशेषताएँ
- Two general-purpose amplifier channels in one package (बनामLM258DT)
- Documented 1.1 MHz gain-bandwidth product (बनामTSH22IDT)
- Established same-family ordering lineage (बनामTSB7192IDT)
डिज़ाइन नोट्स
Place the supply-bypass capacitor adjacent to the LM258AYDT supply and ground pins, and use the shortest practical connection to the device. Keep the feedback loop compact, particularly around inverting inputs, because parasitic resistance and capacitance can alter loop gain and phase margin. Route input and feedback nets away from switching nodes and high-current return paths to reduce common-mode pickup and instability.
Do not assume that any SO8 dual op amp is interchangeable with the LM258AYDT. Before substitution, compare every pin, the supply range, input common-mode range, output swing, input offset, input bias current, output-current capability, slew rate, noise, and stability behavior. Pay particular attention to automotive or industrial temperature requirements, because an apparently identical package does not imply identical qualification.
For sensor and low-level input stages, evaluate source impedance against input bias current and capacitive loading before choosing feedback resistors. Very high resistance values can create leakage-induced offset and noise, while very low values can increase output-current demand and power consumption. Use short guarded traces, clean ground returns, and a defined low-pass network to balance bandwidth against unwanted high-frequency noise.
अनुपालन जानकारी
Compliance status was not stated for the exact LM258AYDT ordering code and must be confirmed from the manufacturer product documentation.