onsemi

LM2903NG - Dual Low-Offset Voltage Comparator | onsemi | PDIP-8

MPN: LM2903NG ✓ सक्रिय
2 V to 36 V Vdss 250 nA Id PDIP-8 (8-pin through-hole) Package
न्यूनतम ऑर्डर मात्रा: 1 |

LM2903NG अवलोकन

The onsemi LM2903NG is a dual independent precision voltage comparator with low input offset voltage, open-collector outputs, and single or split supply operation from 2V to 36V, housed in an 8-pin PDIP through-hole package. The device operates over -40C to +105C and supports input common-mode voltage ranges down to ground.

A voltage comparator is an analog circuit element that compares two input voltages and drives its output to indicate which input is higher. Comparators sit within the broader amplifier IC and signal-conditioning hierarchy of power management and analog semiconductor systems. Unlike an operational amplifier, a comparator is intentionally optimized for fast, saturated switching between two output states rather than linear amplification, and the LM2903 family adds an open-collector output stage that lets multiple devices share a common pull-up node for wired-OR logic.

Key features include a supply range of 2V to 36V (single supply) or +/-1V to +/-18V (split supply), input common-mode range that extends to the negative rail, and very low input bias current of about 250nA. The typical response time is approximately 1.5 microseconds, which suits general-purpose threshold detection, level shifting, and oscillator timing rather than high-speed clocking.

The LM2903 architecture uses two fully independent comparator channels sharing one die and supply pins. Each channel has its own inverting and non-inverting inputs plus an open-collector output, so external pull-up resistors define the output high level, allowing interface to logic families at any voltage up to the supply rails.

Typical applications include power-supply undervoltage and overvoltage supervision, battery threshold monitoring, window comparators, relaxation oscillators, and sensor threshold detection in industrial and automotive-adjacent environments. The wide supply range makes it a natural fit for 5V, 12V, and 24V industrial rails.

For design, always include a pull-up resistor on each open-collector output (typically 1k to 10k ohm), and add hysteresis with positive feedback when comparing slowly moving signals to avoid output chatter near the threshold.

This page synthesizes datasheet parameters, drop-in alternatives, practical design notes, and application guidance not found together in the manufacturer datasheet.

के लिए ड्रॉप-इन विकल्प LM2903NG — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

इस सीरीज़ के वेरिएंट

समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं LM2903NG (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Package, Output Type, Comparator Type, Number of Comparators, Operating Temperature Range.

Texas Instruments
Package: 8-Pin PDIP (DIP-8, N suffix)
Output Type: Open-Collector / Open-Drain
Comparator Type: Low Offset Voltage, Dual Differential
इसके साथ तुलना करें LM2903NG →
Texas Instruments
Package: 8-pin PDIP
Comparator Type: Dual differential comparator
Number of Comparators: 2
इसके साथ तुलना करें LM2903NG →
Texas Instruments
Package: 8-pin PDIP
Comparator Type: Dual differential comparator
इसके साथ तुलना करें LM2903NG →
Texas Instruments
Package: 8-PDIP (DIP-8, through-hole)
Output Type: Open-Collector / Open-Drain (single-ended)
Comparator Type: Dual General-Purpose Comparator
इसके साथ तुलना करें LM2903NG →

LM2903VNG

✅ ड्रॉप-इन
📦 PDIP-8
extended V-family variant of the same 2903 core, wider guaranteed supply/differential input range, same 8-pin PDIP footprint

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

LM2903N

✅ ड्रॉप-इन
Texas Instruments
📦 PDIP-8
Low Offset Voltage, Dual Differential · 2 (dual independent) · Open-Collector / Open-Drain · 2 V to 36 V · ±1 V to ±18 V · 2.5 mV (LM2903 grade) · 25 nA · Includes ground (negative rail)

कीमत के लिए संपर्क करें

डेटाशीट देखें →

LM2903P

✅ ड्रॉप-इन
Texas Instruments
📦 PDIP-8
Dual differential comparator · 2 · Open-collector · Rail-to-rail · 2 V minimum · Up to 38 V for LM2903B family · 0.37 mV for LM2903B family · 3.5 nA for LM2903B family

कीमत के लिए संपर्क करें

डेटाशीट देखें →

LM293P

✅ ड्रॉप-इन
Texas Instruments
📦 PDIP-8
Dual differential comparator · 2 channels · 2 V to 36 V · 300 ns · Open-collector · Rail-to-rail · Industrial grade · Standard general-purpose comparator

कीमत के लिए संपर्क करें

डेटाशीट देखें →

LM393N

✅ ड्रॉप-इन
Texas Instruments
📦 PDIP-8
Dual General-Purpose Comparator · 2 (dual) · Open-Collector / Open-Drain (single-ended) · 5 mV (LM393N); 2 mV (LM193/LM393A grade) · 25 nA · 2 V to 36 V · ±1 V to ±18 V · 16 mA

कीमत के लिए संपर्क करें

डेटाशीट देखें →

LM2903NG Maximum Ratings और Electrical Characteristics

Number of Comparators 2 (dual independent)
Supply Voltage Range (Single) 2 V to 36 V
Supply Voltage Range (Split) +/-1 V to +/-18 V
Input Offset Voltage 1 mV typ (low offset)
Input Bias Current 250 nA
Response Time (typ) 1.3 us to 1.5 us
आउटपुट प्रकार Open-Collector
Input Common-Mode Range Extends to ground (negative rail) with single supply
ऑपरेटिंग तापमान रेंज -40C to +105C
पैकेज PDIP-8 (8-pin through-hole)
माउंटिंग प्रकार Through Hole
Family LM393 / LM2903 series

LM2903NG पिन कॉन्फ़िगरेशन

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
पिन 1 OUT A — Comparator A output (open-collector, requires pull-up)
पिन 2 IN A- — Comparator A inverting input
पिन 3 IN A+ — Comparator A non-inverting input
पिन 4 GND / V- — Ground or negative supply
पिन 5 IN B+ — Comparator B non-inverting input
पिन 6 IN B- — Comparator B inverting input
पिन 7 OUT B — Comparator B output (open-collector, requires pull-up)
पिन 8 VCC / V+ — Positive power supply

सामान्य अनुप्रयोग

LM2903NG के लिए उपयुक्त है 6 अनुप्रयोगs: Power Supply Undervoltage / Overvoltage Supervision, Battery Voltage Monitoring and Protection, Relaxation Oscillators and Timers, Industrial Sensor Threshold Detection, Window Comparators for Voltage Screening, Level Shifting and Logic Interfacing.

⚡

Power Supply Undervoltage / Overvoltage Supervision

The LM2903NG is a classic choice for power-rail supervision because its 2V to 36V single-supply range lets one IC monitor 5V, 12V, or 24V rails, while its common-mode input range extending to ground allows sensing a rail that collapses to 0V during fault conditions. A resistor divider scales the monitored rail to one input and a reference divider sets the threshold on the other; the open-collector output then sinks a pull-up tied to the supervising logic supply, giving clean level translation from a 24V analog domain to 5V or 3.3V MCU GPIOs. For slow-moving fault conditions, add positive-feedback hysteresis (typically 100k from output to the non-inverting input) to prevent chatter near the threshold. The 1.5 microsecond response time is fully adequate for supply-fault timescales of milliseconds.

🔋

Battery Voltage Monitoring and Protection

Battery stacks for 12V lead-acid, 24V telecom, and multi-cell lithium systems fall within the LM2903NG's 2V to 36V supply envelope, and the 250nA input bias current imposes negligible drain on the monitored cell. Wire the battery node through a precision divider to one input, derive a threshold from a reference or a zener-derived divider on the other, and use the open-collector output to drive a warning LED, relay, or shutdown signal. Because the comparator can run from the battery itself while the output pull-up references a downstream logic rail, level shifting is free. Design the divider impedance in the 10k to 100k range to balance monitoring accuracy against quiescent drain, and remember the comparator only sinks current, so the indicator load is placed between pull-up supply and the output pin.

🔧

Relaxation Oscillators and Timers

With positive feedback around one channel, the LM2903NG forms a reliable relaxation oscillator: the open-collector output alternately charges and discharges a timing capacitor through resistors, and the comparator switches at the hysteresis thresholds set by the feedback divider. The 1.5 microsecond typical response time caps practical frequency in the tens to hundreds of kilohertz range, which is ample for PWM carriers, blinkers, clock sources for slow logic, and tone generation. The open-collector output makes it easy to gate the oscillator by wiring the output node with other open-drain devices, and the wide 2V to 36V supply lets the same circuit run from raw industrial power without regulation. Keep timing resistors above a few kilohms so comparator input bias current (250nA) does not shift the frequency.

🏭

Industrial Sensor Threshold Detection

In factory automation, signals from NTC thermistors, photocells, pressure switches, and current-sense shunts are slow-moving ground-referenced voltages - exactly the regime where the LM2903NG's common-mode range to ground and 2V to 36V single-supply tolerance excel. One channel can compare a thermistor divider against a setpoint, while the second channel independently handles an overcurrent shunt threshold, giving two supervision functions in one PDIP-8 package on a -40C to +105C industrial ambient. The through-hole package also supports field-serviceable boards and high-vibration environments where SMD parts are risky. Apply 10-50 mV of hysteresis via positive feedback when sensors dwell near the threshold, and place a small capacitor across the input divider to filter contact bounce and industrial noise pickup.

🖥️

Window Comparators for Voltage Screening

Both channels of the LM2903NG can share one input signal to implement a window comparator: one channel flags when the signal exceeds the upper limit and the other flags when it falls below the lower limit. Wire the two open-collector outputs together with a single pull-up resistor to build a free wired-AND OK/FAULT signal - a topology only possible because of the open-collector output stage. This is widely used to screen supply voltages, cell voltages, and analog sensor outputs against a pass band. The 1 mV class typical offset voltage keeps window boundaries accurate to a few millivolts with reasonable divider design, and the -40C to +105C range qualifies the circuit for industrial enclosures. Use 1% or better resistors for the limit dividers to preserve window accuracy.

🌐

Level Shifting and Logic Interfacing

Because the LM2903NG output is open-collector, its pull-up can be tied to any logic rail up to the output transistor rating, letting the comparator bridge a high-voltage analog domain to a low-voltage digital domain. A 24V industrial signal can be compared against a threshold and presented directly to 3.3V or 5V MCU inputs with nothing more than one pull-up resistor. This removes the need for dedicated level-shifter ICs in simple on/off detection. The 250nA input bias current permits high-impedance dividers (100k class) so the sensing circuit barely loads the source. Add a series input resistor and small clamp consideration when inputs may be driven below ground during transients, since the classic 2903 input structure limits how far the inputs may be taken beyond the rails.

अनुशंसित उत्पादों का सारांश

TL431 Precision shunt reference for threshold setting उपयोग में: Power Supply Undervoltage / Overvoltage Supervision, Battery Voltage Monitoring and Protection, Window Comparators for Voltage Screening LM2903VNG Extended-range dual comparator on same footprint उपयोग में: Power Supply Undervoltage / Overvoltage Supervision, Battery Voltage Monitoring and Protection, Relaxation Oscillators and Timers, Industrial Sensor Threshold Detection, Window Comparators for Voltage Screening, Level Shifting and Logic Interfacing NE555 Timer alternative for longer-period timing उपयोग में: Relaxation Oscillators and Timers ACS712 Allegro MicroSystems उपयोग में: Industrial Sensor Threshold Detection MC1489NG4 Texas Instruments उपयोग में: Level Shifting and Logic Interfacing
What is the supply voltage range of the LM2903NG?
The LM2903NG operates from a single supply of 2V to 36V or a split supply of +/-1V to +/-18V. According to the onsemi datasheet, this wide range lets the same dual comparator serve 5V, 12V, and 24V industrial rails, and the input common-mode range extends to ground in single-supply operation, which is essential for ground-referenced sensor threshold detection without a negative rail.
What is the difference between LM2903NG and LM393?
The LM2903NG is the industrial-temperature-grade member of the same LM393 comparator family, rated from -40C to +105C, while consumer-grade LM393 variants are typically rated to +70C or +85C. Both are dual low-offset voltage comparators with open-collector outputs in pin-compatible packages. Electrically they share the same die family and typical specifications, so the LM2903NG is selected when industrial ambient temperatures above consumer limits must be tolerated.
What is the best drop-in replacement for LM2903NG?
The best drop-in replacement is Texas Instruments LM2903N, which is pin-for-pin compatible in the same 8-pin PDIP package and offers equivalent dual low-offset comparator performance. STMicroelectronics LM2903P is another pin-compatible PDIP-8 option. Within onsemi, the LM2903VNG offers the same footprint with extended supply capability. All of these preserve the open-collector output topology, so no PCB or pull-up resistor changes are required when substituting.
LM2903NG vs TI LM2903N - which should I choose?
Both are pin-for-pin dual comparators in PDIP-8 with equivalent low offset voltage and open-collector outputs, so for most designs either part works. Choose the onsemi LM2903NG if your approved-vendor list or existing BOM already qualifies onsemi, or if supply conditions favor onsemi stock. Choose the TI LM2903N if you need TI's documentation ecosystem or want dual sourcing coverage for the same footprint. The key engineering parameters - 2V to 36V supply, common-mode to ground, and -40C to +105C operation - are equivalent.
When should I choose LM2903NG over a faster comparator like TLV3501?
Choose the LM2903NG when your application is low-speed threshold detection and you value low cost, wide 2V to 36V supply tolerance, and through-hole serviceability. Its typical 1.3 to 1.5 microsecond response time is far slower than the TLV3501's nanosecond-class speed, so for fast edge detection or clock comparison the TLV family is required. For undervoltage locks, battery monitors, and slow sensor thresholds in industrial equipment, the LM2903NG's wide supply range and rugged open-collector output make it the more practical and economical choice.
Is LM2903NG suitable for battery voltage monitoring?
Yes, the LM2903NG is well suited for battery voltage monitoring. Its single-supply range of 2V to 36V covers single-cell lithium, 12V lead-acid, and 24V battery stacks, and the input common-mode range extending to ground allows sensing a battery voltage that discharges all the way to 0V. The low 250nA input bias current minimizes drain on the monitored cell. Wire the battery node through a resistor divider to one input, a reference divider to the other, and use the open-collector output with a pull-up to drive an MCU GPIO or warning LED.
What can replace LM2903NG?
Pin-compatible PDIP-8 replacements for the LM2903NG include Texas Instruments LM2903N, STMicroelectronics LM2903P and LM293P, and Texas Instruments LM393N, all dual open-collector comparators in the same 8-pin through-hole footprint. Within onsemi, LM2903VNG is the same-package variant with extended specifications. If the package may change, the surface-mount onsemi LM2903DR2G is electrically equivalent but requires a different footprint, so it is a redesign substitute rather than a drop-in replacement.
Where can I download the LM2903NG datasheet PDF?
The LM2903NG datasheet PDF is published by onsemi on its official product page and is also available through datasheet archives such as alldatasheet.com, which hosts the onsemi LM2903NG PDF. The datasheet contains the full electrical characteristics table, package dimensions for the PDIP-8 outline, typical application circuits, and thermal information. Always use the manufacturer's latest revision when finalizing a design, since comparator specifications such as offset voltage and response time carry typ/max limits that are updated with process revisions.
What are the key specifications of LM2903NG that engineers should know?
The LM2903NG is onsemi's dual low-offset voltage comparator in PDIP-8: 2V to 36V single supply (or +/-1V to +/-18V split), input offset of about 1mV typical, input bias current near 250nA, open-collector outputs requiring pull-up resistors, common-mode input range down to ground, approximately 1.5 microsecond response time, and -40C to +105C operation. These numbers make it a general-purpose, wide-supply, industrial-grade comparator rather than a high-speed or precision part.
Does LM2903NG need pull-up resistors on its outputs?
Yes, the LM2903NG has open-collector outputs that sink current but cannot source it, so each output requires an external pull-up resistor to the desired logic voltage. Typical values are 1k to 10k ohm; lower values improve rise time and noise immunity at the cost of higher sink current when the output is low. A major benefit is that each output can be pulled up to a different voltage rail, for example 5V logic while the comparator runs from a 24V industrial supply, provided the pull-up voltage does not exceed the output transistor rating.
What is the operating temperature range of LM2903NG?
The LM2903NG is rated from -40C to +105C, which places it in the industrial temperature class according to onsemi product listings. This range covers factory floors, outdoor enclosures, and most automotive-adjacent cabin environments, though it is not the AEC-Q100 qualified automotive variant. For designs needing guaranteed automotive qualification, select the appropriate automotive-grade member of the LM2903 family instead and verify the package suffix on the manufacturer product page before release.
Where to buy LM2903NG and what is its price?
You can purchase the LM2903NG through the Request a Quote form on this page, which returns current stock availability, unit pricing, and lead time directly from XAIPART. Distributor inventory levels for this through-hole comparator change frequently, so requesting a quote is the fastest way to get an accurate quantity price and delivery date for your build. For volume requirements, include your annual usage in the quote request so appropriate tier pricing can be arranged.
What is the lead time and packaging for LM2903NG?
The LM2903NG ships in bulk tube packaging suited to through-hole assembly, and it is an active part in onsemi's catalog, so standard production quantities are generally available from distributor stock without long factory lead times. Exact lead time depends on current inventory at the moment of ordering, so request the confirmed delivery date through the Request a Quote form on this page. Because it is a PDIP through-hole part, it is also convenient for prototyping, breadboarding, and repair of legacy industrial equipment.
Can LM2903NG replace LM2903VNG in my design?
The LM2903NG can replace the LM2903VNG in the same 8-pin PDIP footprint for applications within the standard LM2903 ratings, but check your supply and input conditions first. The V suffix denotes an extended version of the family with a wider guaranteed supply and differential input range, so if your circuit exploits voltages near the upper extended limits, confirm the LM2903NG datasheet maximum ratings cover your operating point. For conventional 2V to 36V single-supply designs the two parts are functionally interchangeable.
Is LM2903NG the same as LM293P?
They are closely equivalent but not identical part numbers. The LM2903NG is onsemi's dual comparator in PDIP-8 rated -40C to +105C, while the LM293P from STMicroelectronics is the dual LM293 comparator, also in a DIP-8 package, targeting similar industrial temperature ranges. Both share the classic LM393-style pinout with open-collector outputs, so they are drop-in compatible on the same footprint. Verify the exact offset voltage limits and supply range on each manufacturer datasheet for the suffix you are sourcing, as marketing grades differ slightly between families.

के लिए इंजीनियरिंग संदर्भ डेटा LM2903NG — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose the LM2903NG when you need a rugged, low-cost, dual comparator for ground-referenced threshold detection on industrial rails from 2V to 36V, in a through-hole package that survives field service and high vibration. Choose onsemi LM2903VNG if your supply or input voltages approach extended limits, since it is footprint-identical with wider guarantees. Choose TI LM2903N or ST LM2903P for dual-sourcing coverage of the same footprint with equivalent industrial ratings. Choose TI LM393N only for cost-sensitive, controlled-temperature consumer designs, because its commercial temperature rating does not cover -40C to +105C. Avoid this family altogether for nanosecond-class edge detection - use a fast comparator such as the TLV3501 instead - and for sub-millivolt precision thresholds use a precision comparator family. For everything else, the LM2903NG is the default workhorse.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद LM2903VNG LM2903N LM2903P LM293P LM393N
Package PDIP-8 PDIP-8 - same PDIP-8 - same PDIP-8 - same PDIP-8 - same PDIP-8 - same
Brand onsemi onsemi Texas Instruments STMicroelectronics STMicroelectronics Texas Instruments
Supply Voltage Range 2 V to 36 V 2 V to 36 V (extended grade) 2 V to 36 V 2 V to 36 V 2 V to 36 V 2 V to 36 V
Operating Temperature -40C to +105C -40C to +125C (extended) -40C to +105C -40C to +105C -40C to +105C 0C to +70C (commercial)
Output Type Open-Collector Open-Collector Open-Collector Open-Collector Open-Collector Open-Collector
Number of Comparators 2 2 2 2 2 2
Input Bias Current 250 nA 250 nA 250 nA 250 nA 250 nA 250 nA
Mounting Type Through Hole Through Hole Through Hole Through Hole Through Hole Through Hole

मुख्य विशेषताएँ

  • Industrial temperature rating (बनामLM393N)
  • Extended V-family option on identical footprint (बनामLM2903VNG)
  • Through-hole serviceability with dual channels (बनामLM2903P)

डिज़ाइन नोट्स

The LM2903NG outputs are open-collector and will never go high without an external pull-up resistor. Always connect a 1k to 10k resistor from each output to the desired logic rail. Forgetting the pull-up is the single most common first-time failure. Also, the classic LM2903 input structure limits how far below the negative rail the inputs may be driven; if inputs can go negative during faults, add series resistors to limit input current.

When comparing slow analog signals such as thermistor dividers or battery dividers, add hysteresis with positive feedback (for example, a 100k resistor from the output to the non-inverting input, scaled against the source divider impedance) to create 10-50 mV of hysteresis. Without hysteresis, noise on the input will cause multiple output transitions near the threshold, producing chatter that corrupts MCU interrupt counts. The 1.5 microsecond response time makes this chatter visible even on modest noise.

Although the PDIP-8 through-hole package is forgiving, keep the input traces short and route them away from switching nodes to avoid millivolt-level offset errors; with only about 1 mV typical offset, induced noise directly shifts the effective threshold. Place a 100 nF decoupling capacitor close to pin 8 and pin 4. The large through-hole pitch also makes this part ideal for breadboard prototyping before committing to a surface-mount production layout.

Estimated: at a 24 V single supply with 5 V pull-ups on both outputs and typical quiescent current, total board power attributable to the LM2903NG is dominated by the pull-up sink current when outputs are low (for example 5 V / 4.7k = ~1 mA per low output). Size pull-ups as high as signal-speed needs allow to minimize dissipation and supply loading on battery-powered monitors.

अनुपालन जानकारी

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

Compliance status should be confirmed on the onsemi product page for the exact PDIP-8 suffix before ordering for regulated markets.

डेटा सत्यापन तिथि: 2026-11-08 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

lm2903n datasheet LM2903NG datasheet LM2903NG datasheet pdf LM2903NG pinout onsemi LM2903NG LM2903NG equivalent LM2903NG replacement LM2903NG cross reference LM2903NG vs LM2903N LM2903NG price LM2903NG stock LM2903 dual comparator PDIP-8 LM2903NG PDIP-8 pinout LM2903 application circuit

संबंधित कंपोनेंट्स और शब्द

onsemi ON Semiconductor LM2903NG LM2903VNG LM2903N LM2903P LM293P LM393N LM393 series voltage comparator analog comparator amplifier IC open-collector output PDIP-8 dual comparator input offset voltage input bias current hysteresis through-hole undervoltage supervision window comparator RoHS
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें