LM2903NG - Dual Low-Offset Voltage Comparator | onsemi | PDIP-8
Teilenummer: LM2903NG ✓ AktivLM2903NG Übersicht
A voltage comparator is an analog circuit element that compares two input voltages and drives its output to indicate which input is higher. Comparators sit within the broader amplifier IC and signal-conditioning hierarchy of power management and analog semiconductor systems. Unlike an operational amplifier, a comparator is intentionally optimized for fast, saturated switching between two output states rather than linear amplification, and the LM2903 family adds an open-collector output stage that lets multiple devices share a common pull-up node for wired-OR logic.
Key features include a supply range of 2V to 36V (single supply) or +/-1V to +/-18V (split supply), input common-mode range that extends to the negative rail, and very low input bias current of about 250nA. The typical response time is approximately 1.5 microseconds, which suits general-purpose threshold detection, level shifting, and oscillator timing rather than high-speed clocking.
The LM2903 architecture uses two fully independent comparator channels sharing one die and supply pins. Each channel has its own inverting and non-inverting inputs plus an open-collector output, so external pull-up resistors define the output high level, allowing interface to logic families at any voltage up to the supply rails.
Typical applications include power-supply undervoltage and overvoltage supervision, battery threshold monitoring, window comparators, relaxation oscillators, and sensor threshold detection in industrial and automotive-adjacent environments. The wide supply range makes it a natural fit for 5V, 12V, and 24V industrial rails.
For design, always include a pull-up resistor on each open-collector output (typically 1k to 10k ohm), and add hysteresis with positive feedback when comparing slowly moving signals to avoid output chatter near the threshold.
This page synthesizes datasheet parameters, drop-in alternatives, practical design notes, and application guidance not found together in the manufacturer datasheet.
Drop-in-Alternativen für LM2903NG – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit LM2903NG (gleiche Bauform und Footprint) – abweichend in Package, Output Type, Comparator Type, Number of Comparators, Operating Temperature Range.
LM2903VNG
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
LM2903N
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →LM2903P
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →LM293P
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →LM393N
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →LM2903NG Grenzwerte & elektrische Eigenschaften
| Number of Comparators | 2 (dual independent) |
| Supply Voltage Range (Single) | 2 V to 36 V |
| Supply Voltage Range (Split) | +/-1 V to +/-18 V |
| Input Offset Voltage | 1 mV typ (low offset) |
| Input Bias Current | 250 nA |
| Response Time (typ) | 1.3 us to 1.5 us |
| Ausgangstyp | Open-Collector |
| Input Common-Mode Range | Extends to ground (negative rail) with single supply |
| Betriebstemperaturbereich | -40C to +105C |
| Gehäuse | PDIP-8 (8-pin through-hole) |
| Montageart | Through Hole |
| Family | LM393 / LM2903 series |
LM2903NG Pin-Konfiguration
| Pin 1 | OUT A — Comparator A output (open-collector, requires pull-up) |
| Pin 2 | IN A- — Comparator A inverting input |
| Pin 3 | IN A+ — Comparator A non-inverting input |
| Pin 4 | GND / V- — Ground or negative supply |
| Pin 5 | IN B+ — Comparator B non-inverting input |
| Pin 6 | IN B- — Comparator B inverting input |
| Pin 7 | OUT B — Comparator B output (open-collector, requires pull-up) |
| Pin 8 | VCC / V+ — Positive power supply |
Typische Anwendungen
LM2903NG ist geeignet für 6 Anwendungs: Power Supply Undervoltage / Overvoltage Supervision, Battery Voltage Monitoring and Protection, Relaxation Oscillators and Timers, Industrial Sensor Threshold Detection, Window Comparators for Voltage Screening, Level Shifting and Logic Interfacing.
Power Supply Undervoltage / Overvoltage Supervision
The LM2903NG is a classic choice for power-rail supervision because its 2V to 36V single-supply range lets one IC monitor 5V, 12V, or 24V rails, while its common-mode input range extending to ground allows sensing a rail that collapses to 0V during fault conditions. A resistor divider scales the monitored rail to one input and a reference divider sets the threshold on the other; the open-collector output then sinks a pull-up tied to the supervising logic supply, giving clean level translation from a 24V analog domain to 5V or 3.3V MCU GPIOs. For slow-moving fault conditions, add positive-feedback hysteresis (typically 100k from output to the non-inverting input) to prevent chatter near the threshold. The 1.5 microsecond response time is fully adequate for supply-fault timescales of milliseconds.
Empfohlen
Battery Voltage Monitoring and Protection
Battery stacks for 12V lead-acid, 24V telecom, and multi-cell lithium systems fall within the LM2903NG's 2V to 36V supply envelope, and the 250nA input bias current imposes negligible drain on the monitored cell. Wire the battery node through a precision divider to one input, derive a threshold from a reference or a zener-derived divider on the other, and use the open-collector output to drive a warning LED, relay, or shutdown signal. Because the comparator can run from the battery itself while the output pull-up references a downstream logic rail, level shifting is free. Design the divider impedance in the 10k to 100k range to balance monitoring accuracy against quiescent drain, and remember the comparator only sinks current, so the indicator load is placed between pull-up supply and the output pin.
Empfohlen
Relaxation Oscillators and Timers
With positive feedback around one channel, the LM2903NG forms a reliable relaxation oscillator: the open-collector output alternately charges and discharges a timing capacitor through resistors, and the comparator switches at the hysteresis thresholds set by the feedback divider. The 1.5 microsecond typical response time caps practical frequency in the tens to hundreds of kilohertz range, which is ample for PWM carriers, blinkers, clock sources for slow logic, and tone generation. The open-collector output makes it easy to gate the oscillator by wiring the output node with other open-drain devices, and the wide 2V to 36V supply lets the same circuit run from raw industrial power without regulation. Keep timing resistors above a few kilohms so comparator input bias current (250nA) does not shift the frequency.
Empfohlen
Industrial Sensor Threshold Detection
In factory automation, signals from NTC thermistors, photocells, pressure switches, and current-sense shunts are slow-moving ground-referenced voltages - exactly the regime where the LM2903NG's common-mode range to ground and 2V to 36V single-supply tolerance excel. One channel can compare a thermistor divider against a setpoint, while the second channel independently handles an overcurrent shunt threshold, giving two supervision functions in one PDIP-8 package on a -40C to +105C industrial ambient. The through-hole package also supports field-serviceable boards and high-vibration environments where SMD parts are risky. Apply 10-50 mV of hysteresis via positive feedback when sensors dwell near the threshold, and place a small capacitor across the input divider to filter contact bounce and industrial noise pickup.
Empfohlen
Window Comparators for Voltage Screening
Both channels of the LM2903NG can share one input signal to implement a window comparator: one channel flags when the signal exceeds the upper limit and the other flags when it falls below the lower limit. Wire the two open-collector outputs together with a single pull-up resistor to build a free wired-AND OK/FAULT signal - a topology only possible because of the open-collector output stage. This is widely used to screen supply voltages, cell voltages, and analog sensor outputs against a pass band. The 1 mV class typical offset voltage keeps window boundaries accurate to a few millivolts with reasonable divider design, and the -40C to +105C range qualifies the circuit for industrial enclosures. Use 1% or better resistors for the limit dividers to preserve window accuracy.
Empfohlen
Level Shifting and Logic Interfacing
Because the LM2903NG output is open-collector, its pull-up can be tied to any logic rail up to the output transistor rating, letting the comparator bridge a high-voltage analog domain to a low-voltage digital domain. A 24V industrial signal can be compared against a threshold and presented directly to 3.3V or 5V MCU inputs with nothing more than one pull-up resistor. This removes the need for dedicated level-shifter ICs in simple on/off detection. The 250nA input bias current permits high-impedance dividers (100k class) so the sensing circuit barely loads the source. Add a series input resistor and small clamp consideration when inputs may be driven below ground during transients, since the classic 2903 input structure limits how far the inputs may be taken beyond the rails.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für LM2903NG – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | LM2903VNG | LM2903N | LM2903P | LM293P | LM393N |
|---|---|---|---|---|---|---|
| Package | PDIP-8 | PDIP-8 - same | PDIP-8 - same | PDIP-8 - same | PDIP-8 - same | PDIP-8 - same |
| Brand | onsemi | onsemi | Texas Instruments | STMicroelectronics | STMicroelectronics | Texas Instruments |
| Supply Voltage Range | 2 V to 36 V | 2 V to 36 V (extended grade) | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V |
| Operating Temperature | -40C to +105C | -40C to +125C (extended) | -40C to +105C | -40C to +105C | -40C to +105C | 0C to +70C (commercial) |
| Output Type | Open-Collector | Open-Collector | Open-Collector | Open-Collector | Open-Collector | Open-Collector |
| Number of Comparators | 2 | 2 | 2 | 2 | 2 | 2 |
| Input Bias Current | 250 nA | 250 nA | 250 nA | 250 nA | 250 nA | 250 nA |
| Mounting Type | Through Hole | Through Hole | Through Hole | Through Hole | Through Hole | Through Hole |
Wichtigste Unterscheidungsmerkmale
- Industrial temperature rating (vs. LM393N)
- Extended V-family option on identical footprint (vs. LM2903VNG)
- Through-hole serviceability with dual channels (vs. LM2903P)
Designhinweise
The LM2903NG outputs are open-collector and will never go high without an external pull-up resistor. Always connect a 1k to 10k resistor from each output to the desired logic rail. Forgetting the pull-up is the single most common first-time failure. Also, the classic LM2903 input structure limits how far below the negative rail the inputs may be driven; if inputs can go negative during faults, add series resistors to limit input current.
When comparing slow analog signals such as thermistor dividers or battery dividers, add hysteresis with positive feedback (for example, a 100k resistor from the output to the non-inverting input, scaled against the source divider impedance) to create 10-50 mV of hysteresis. Without hysteresis, noise on the input will cause multiple output transitions near the threshold, producing chatter that corrupts MCU interrupt counts. The 1.5 microsecond response time makes this chatter visible even on modest noise.
Although the PDIP-8 through-hole package is forgiving, keep the input traces short and route them away from switching nodes to avoid millivolt-level offset errors; with only about 1 mV typical offset, induced noise directly shifts the effective threshold. Place a 100 nF decoupling capacitor close to pin 8 and pin 4. The large through-hole pitch also makes this part ideal for breadboard prototyping before committing to a surface-mount production layout.
Estimated: at a 24 V single supply with 5 V pull-ups on both outputs and typical quiescent current, total board power attributable to the LM2903NG is dominated by the pull-up sink current when outputs are low (for example 5 V / 4.7k = ~1 mA per low output). Size pull-ups as high as signal-speed needs allow to minimize dissipation and supply loading on battery-powered monitors.
Compliance-Informationen
Compliance status should be confirmed on the onsemi product page for the exact PDIP-8 suffix before ordering for regulated markets.