onsemi

LM2904ADMG - Dual 26V Low-Power Op Amp | onsemi

MPN: LM2904ADMG ✓ सक्रिय
3 V to 26 V Vdss 8-MSOP, 3.00 mm width Package
न्यूनतम ऑर्डर मात्रा: 1 |

LM2904ADMG अवलोकन

The onsemi LM2904ADMG is a dual, general-purpose operational amplifier designed for low-power signal-conditioning applications over a 3 V to 26 V supply range. It provides two amplifier circuits, a common-mode input range that extends to ground or VEE, and operation from either a single supply or split supplies. The device is supplied in an 8-MSOP package and is specified for temperatures from -40°C to +105°C.

An operational amplifier is an analog signal-processing IC that uses high open-loop gain to amplify the difference between two input voltages. The LM2904 family belongs to the broader hierarchy of voltage-feedback operational amplifiers, analog amplifiers, and integrated signal-chain devices. Its common-mode capability makes it useful when signals approach the lower supply rail, while dual integration reduces board area in circuits requiring two independent amplifier channels.

Key operating characteristics include a low-power architecture, a 3 V to 26 V supply-voltage capability, and a slew rate of 0.6 V/µs. The 8-MSOP package provides a compact surface-mount option for industrial and embedded equipment. Its specified temperature range supports applications across extended commercial and industrial environments. Designers should verify gain-bandwidth, input-bias-current, output-current, noise, and input-offset parameters against their operating conditions before finalizing a high-impedance or precision design.

The LM2904ADMG uses the circuit design established for quad operational amplifiers, with two amplifiers per package. Its common-mode input voltage range extending toward ground or VEE is particularly useful in single-supply sensor interfaces, transimpedance stages, filters, and low-level signal amplifiers. The split-supply option permits operation around a zero-volt reference, while single-supply operation simplifies portable and industrial control systems.

Typical applications include current monitoring, sensor conditioning, audio preamplification, active filtering, and general-purpose analog signal processing. In a current-sensing application, the device can amplify the voltage developed across a low-value shunt while operating from a split supply. In a sensor interface, the common-mode range allows closer proximity to the lower rail than a conventional bipolar input amplifier. Input and output stability should be checked with the external resistor and capacitance values used in the final circuit.

A key design consideration is power-supply decoupling. Place a suitable bypass capacitor close to the supply pins and route return current through a low-impedance ground path. Avoid excessive output loading and confirm that the selected feedback network preserves the required gain-bandwidth and phase-margin behavior. For AC-coupled inputs, add suitable input bias-current compensation when source resistance is high.

This page combines the LM2904ADMG electrical identity, package and temperature information with replacement guidance, comparison parameters, and practical design considerations. It also identifies which replacement candidates preserve the 8-MSOP footprint and where application-specific validation remains necessary.

के लिए ड्रॉप-इन विकल्प LM2904ADMG — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

LM2904ADM

✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित
📦 8-MSOP
Same LM2904A dual-amplifier architecture and 8-MSOP footprint; primary distinction is the ordering or shipment format, with no electrical percentage difference identified.

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

LM2904ADMG Maximum Ratings और Electrical Characteristics

Amplifier Type General-purpose operational amplifier
Number of Channels 2 channels
Supply Voltage Range 3 V to 26 V
Common-Mode Input Range Extends to ground or VEE
Supply Configuration Single supply or split supply
Slew Rate 0.6 V/µs
ऑपरेटिंग तापमान रेंज -40°C to +105°C
पैकेज 8-MSOP, 3.00 mm width
माउंटिंग प्रकार Surface mount
Packaging Tape and reel

LM2904ADMG पिन कॉन्फ़िगरेशन

MSOP-8 Package Pinout Diagram MSOP-8 3x3mm, P0.65mm, JEDEC MO-187. 1 8 2 7 3 6 4 5 MSOP-8
पिन 1 OUT1 — Output of amplifier channel 1
पिन 2 IN1- — Inverting input of amplifier channel 1
पिन 3 IN1+ — Non-inverting input of amplifier channel 1
पिन 4 V- — Negative supply connection
पिन 5 IN2+ — Non-inverting input of amplifier channel 2
पिन 6 IN2- — Inverting input of amplifier channel 2
पिन 7 OUT2 — Output of amplifier channel 2
पिन 8 V+ — Positive supply connection

सामान्य अनुप्रयोग

LM2904ADMG के लिए उपयुक्त है 6 अनुप्रयोगs: Industrial Sensor Signal Conditioning, Current-Shunt Monitoring, Audio Preamplification, Active Filter and Equalization, Battery-Powered Monitoring, Portable Instrumentation Front End.

🏭

Industrial Sensor Signal Conditioning

The LM2904ADMG fits low-level industrial sensor conditioning because it provides two amplifier channels, a 3 V to 26 V supply range, and a common-mode input range extending toward ground or VEE. Place one channel around the sensor or bridge output and use the second for gain or filtering. The -40°C to +105°C specification suits extended industrial environments. Designers should verify the actual input offset, bias current, output swing, noise, and stability against the selected sensor impedance. A single supply is practical when the signal remains within the common-mode range, while split supplies allow operation around a zero-volt reference for bipolar sensor signals.

⚡

Current-Shunt Monitoring

The LM2904ADMG is suitable for amplifying the small differential voltage generated by a current-sense shunt while keeping the circuit compact. Two channels can monitor positive and negative portions of a bipolar waveform, or one channel can amplify the shunt signal while the other provides offset or filtering. Its common-mode input capability extending toward ground or VEE helps when the shunt voltage is close to the lower supply rail. Confirm the common-mode range, input offset, gain error, and output drive at the operating voltage. Decouple the supply pins locally and use a feedback layout that preserves the amplifier’s stability with the shunt and routing capacitance.

🎧

Audio Preamplification

The LM2904ADMG can provide basic audio preamplification in low-cost analog signal chains because it combines two channels with a 0.6 V/µs slew rate and a supply range up to 26 V. One channel can amplify a microphone or line-level source while the second supports volume control, tone shaping, or buffering. The common-mode range extending toward ground or VEE is useful in single-supply microphone circuits where the input lies close to the lower rail. Input-bias-current compensation, output loading, and output-swing headroom should be evaluated for the source impedance and channel configuration. Keep input routing short and connect the return path directly to the device ground reference.

📡

Active Filter and Equalization

The LM2904ADMG is applicable to first-order active filters and equalization networks that operate within its bandwidth and slew-rate limits. Its dual configuration supports a two-pole filter using one amplifier per section or permits a signal-conditioning stage followed by an output filter. The 3 V to 26 V operating range supports portable, industrial-control, and higher-voltage analog systems. Because a general-purpose amplifier is not optimized for very high frequency or extremely low noise, calculate the gain-bandwidth margin, phase margin, and large-signal slew requirement for the target filter. Place compensation capacitors and feedback components close to their associated pins to minimize parasitic feedback effects.

📱

Battery-Powered Monitoring

The LM2904ADMG can monitor and control low-voltage battery systems when the selected supply remains within its 3 V to 26 V operating range. Its low-power design and common-mode input range extending toward ground or VEE are useful for battery-voltage sensing and threshold detection when the signal approaches the lower rail. The second channel can monitor another sensor or supervise a control threshold. Calculate the maximum supply current for the battery budget and verify that the output can reach the required logic levels. Use a local supply bypass capacitor, minimize leakage into high-impedance sensing nodes, and confirm the complete operating-current budget across temperature and production tolerances.

🧩

Portable Instrumentation Front End

The LM2904ADMG suits compact instrumentation front ends that need two general-purpose amplifier channels within a 3 V to 26 V supply envelope. One channel can condition a transducer output while the other buffers a reference or drives an analog-to-converter input. The 8-MSOP package reduces PCB footprint, while the -40°C to +105°C rating supports equipment expected to operate across industrial temperature ranges. Check the input bias current when working with high-source-impedance sensors, and ensure that the ADC input range is compatible with the amplifier’s output swing. Maintain a compact ground return around the two channels and use separate routing where one amplifier handles a high-gain signal and the other handles a faster or noisier path.

What is the LM2904ADMG?
The LM2904ADMG is an onsemi dual general-purpose operational amplifier in an 8-MSOP package. According to the manufacturer datasheet, it uses the circuit designs developed for the quad LM2904 family, provides low power drain, and supports single-supply or split-supply operation. The device contains two amplifier circuits and has a common-mode input voltage range extending toward ground or VEE.
What is the supply voltage range of LM2904ADMG?
The LM2904ADMG operates from 3 V to 26 V. This range supports 3.3 V and 5 V systems as well as higher-voltage industrial rails. The manufacturer identifies the device as suitable for both single and split supplies, but actual input, output, and common-mode limits must remain within the datasheet limits for the selected amplifier configuration.
What is the slew rate of LM2904ADMG?
The specified slew rate of LM2904ADMG is 0.6 V/µs. This parameter limits how quickly the output can change under a large-signal condition and is especially relevant for waveform shaping, active filters, and sensor interfaces. Slew-rate limitations can cause distortion even when the small-signal gain-bandwidth product appears adequate for the intended frequency.
Where can I download the LM2904ADMG datasheet PDF?
The LM2904ADMG datasheet PDF is available from the onsemi product documentation and through the listed LM2904ADMG datasheet result. The document describes the dual-amplifier configuration, supply range, common-mode capability, electrical characteristics, and package information. Use the manufacturer document for final pin functions, limit values, test conditions, and ordering information.
Where is the LM2904ADMG pinout located?
The LM2904ADMG pinout is shown in the pin-configuration section of the manufacturer datasheet and is represented here for the 8-MSOP package. The two amplifier sections use separate input and output pins, while supply pins serve both channels. Verify the exposed package dimensions and terminal numbering against the drawing for the exact DMG package before laying out a PCB.
Can LM2904ADMG operate from a single 5 V supply?
Yes, LM2904ADMG can operate from a single 5 V supply because its specified operating range is 3 V to 26 V and its common-mode input range extends toward ground or VEE. This makes it suitable for low-level sensor signals referenced near the lower rail. Input and output swing limits and the signal amplitude must be checked to avoid saturation.
What is the best drop-in replacement for LM2904ADMG?
The closest same-family drop-in option identified is the onsemi LM2904ADM, which uses the same 8-MSOP footprint and electrical function, with the distinction primarily involving ordering or shipment format. A second circuit-design review is still required for gain, bias current, offset, noise, stability, and lifecycle requirements. Use the Request a Quote form on this page to discuss replacement sourcing.
Is LM2904ADMG the same as LM2904ADM?
The LM2904ADMG and LM2904ADM belong to the same onsemi LM2904A dual-amplifier family and use the 8-MSOP package. Their naming reflects ordering or packaging differences rather than a change to the basic amplifier architecture. Confirm the exact suffix, package drawings, electrical table, tape-and-reel orientation, and production status before treating one as a replacement for the other.
What can replace LM2904ADMG in an 8-MSOP circuit?
The onsemi LM2904ADM is the identified same-package family replacement for LM2904ADMG. It preserves the dual-amplifier configuration and 8-MSOP footprint, making it the most direct option for engineering review. No additional cross-brand 8-MSOP candidate met the required package and verified-compatibility criteria, so production substitution should be based on a complete comparison of electrical limits and stability.
When should I choose LM2904ADMG over a higher-speed amplifier?
Choose LM2904ADMG when the design needs a low-power, general-purpose dual amplifier and does not require the bandwidth, slew rate, noise, or offset performance of a higher-speed device. Its 0.6 V/µs slew rate and 3 V to 26 V supply capability suit conventional control and signal-conditioning paths. A high-speed amplifier is preferable for wideband or precision applications beyond these limits.
Is LM2904ADMG suitable for industrial sensor conditioning?
Yes, LM2904ADMG is suitable for many industrial sensor-conditioning applications because it is specified from -40°C to +105°C and supports supply voltages up to 26 V. Its common-mode input range extending toward ground or VEE is useful for low-level sensor signals. A production design should still verify input protection, noise, offset stability, output swing, and long-term availability.
LM2904ADMG vs LM2904ADM: which is better for replacement?
LM2904ADM is the more direct replacement candidate because it retains the LM2904A dual-op-amp design and 8-MSOP package, while LM2904ADMG is the tape-and-reel ordering designation for the target circuit. Both should provide equivalent core behavior. Confirm the exact orderable drawing, shipment format, grade, temperature range, and lifecycle before approving a substitution.
Where to buy LM2904ADMG online?
Use the Request a Quote form on this page to request LM2904ADMG availability, minimum order quantity, lead time, and shipment options for the 8-MSOP tape-and-reel configuration. Because the part is presented as a general-purpose dual op amp with extended temperature capability, buyers should request the exact LM2904ADMG suffix rather than a generic LM2904 family designation.
What is the price of LM2904ADMG?
Use the Request a Quote form on this page for the current commercial terms for LM2904ADMG. The form supports a direct request against the exact 8-MSOP tape-and-reel part number, including quantity breaks and production-planning information. Current pricing and availability can change, so the structured quotation is more useful than a static catalog figure.
What is the lead time for LM2904ADMG?
The current lead time for LM2904ADMG should be requested through the Request a Quote form on this page using the exact MPN and required order quantity. Lead time can vary with order size, inventory, packaging format, and production scheduling. Providing a forecast and target date in the request enables the supplier to confirm the most relevant schedule.
Is LM2904ADMG in stock?
Inventory for LM2904ADMG should be confirmed through the Request a Quote form on this page. The listing indicates that LM2904ADMG is offered as an active ordering configuration in 8-MSOP tape-and-reel packaging, but quantity-specific availability is not established without a current quotation. State the required quantity and shipment date when requesting supply confirmation.
What are the key specifications of LM2904ADMG that engineers should know?
The core LM2904ADMG specifications are two amplifier channels, a 3 V to 26 V supply range, a 0.6 V/µs slew rate, and an operating temperature range of -40°C to +105°C in an 8-MSOP package. The common-mode input range extends toward ground or VEE, and the device supports single or split supplies. Check the datasheet for gain-bandwidth, offset, bias-current, noise, and output-swing limits.

के लिए इंजीनियरिंग संदर्भ डेटा LM2904ADMG — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose LM2904ADMG when a design requires two general-purpose amplifier channels, a 3 V to 26 V supply range, and an 8-MSOP footprint. Its common-mode input range extending toward ground or VEE is particularly useful in single-supply sensor and battery-monitoring circuits, while split-supply operation supports signals around a zero-volt reference. The 0.6 V/µs slew rate is appropriate for conventional control, filtering, and instrumentation rather than high-speed waveform work.

For replacement work, LM2904ADM is the closest same-family 8-MSOP candidate identified, but the exact ordering suffix and packaging format should be confirmed before approval. Use a quad amplifier such as LM324KAPWR when four channels are needed, or LM2902-family parts when their lower-power characteristics better match the design. Select a precision or high-speed amplifier instead when input offset, noise, bandwidth, or slew-rate requirements exceed the capabilities of this general-purpose device.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद LM2904ADM
Package 8-MSOP 8-MSOP
Brand onsemi onsemi
Number of Channels 2 2
Supply Voltage Range 3 V to 26 V 3 V to 26 V
Slew Rate 0.6 V/µs 0.6 V/µs
Operating Temperature Range -40°C to +105°C -40°C to +105°C
Common-Mode Input Range Extends to ground or VEE Extends to ground or VEE
Supply Configuration Single supply or split supply Single supply or split supply
Amplifier Type General-purpose General-purpose
Mounting Type Surface mount Surface mount

मुख्य विशेषताएँ

  • Combines two amplifier channels in one compact package (बनामLM324KAPWR)
  • Supports a broad supply-voltage operating range (बनामLM2902KPWR)
  • Common-mode input capability extends toward the lower rail (बनामLM2902MTX)

डिज़ाइन नोट्स

Place the supply bypass capacitor directly between the positive and negative supply pins, with the ground connection following the shortest practical path. Keep input and feedback traces away from the supply and output nets, particularly when a high-value feedback resistor creates a sensitive high-impedance node. The 8-MSOP footprint is compact, so adequate land geometry and assembly clearance remain important even though the package offers limited pin pitch.

Do not assume that the common-mode input range extending toward ground or VEE permits unrestricted operation at the lower rail. Check the complete input and output voltage limits from the manufacturer datasheet for the selected supply, including output-swing headroom. In single-supply designs, verify the input offset and bias-current contribution because those errors can dominate a low-level sensor signal even though the amplifier is operating within its nominal supply range.

Calculate the maximum large-signal input frequency using the required output amplitude and the specified 0.6 V/µs slew rate. If slew-rate distortion appears before the intended bandwidth limit is reached, reduce signal amplitude, increase the supply voltage where allowed, or select a faster amplifier. Also check the gain-bandwidth product and phase margin against the feedback network, including the capacitance introduced by PCB traces and connected test equipment.

For dual-supply operation, connect the midpoint ground and bypass each supply rail independently. The negative supply must remain within its absolute maximum and must not be used as a signal-ground substitute. Evaluate total amplifier dissipation across both channels under worst-case voltage and output conditions, and ensure the PCB thermal design can remove that heat without forcing the junction above its allowable limit.

अनुपालन जानकारी

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

The available product information does not establish RoHS, REACH, halogen-free, conflict-minerals, or AEC-Q100 status. This operational amplifier is not presented as an automotive-qualified device.

डेटा सत्यापन तिथि: 2026-11-17 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

LM2904ADMG datasheet LM2904ADMG pinout LM2904ADMG datasheet pdf LM2904ADMG equivalent LM2904ADMG replacement LM2904ADMG cross reference LM2904ADMG footprint LM2904ADMG price LM2904ADMG stock onsemi LM2904ADMG LM2904ADMG 8-MSOP op amp LM2904ADMG sensor conditioning LM2904ADMG vs LM2904ADM What is the LM2904ADMG pin configuration?

संबंधित कंपोनेंट्स और शब्द

onsemi LM2904ADMG LM2904ADM LM2904 LM324KAPWR LM2902KPWR operational amplifier dual operational amplifier voltage-feedback amplifier analog amplifier signal-conditioning IC common-mode input voltage range slew rate single-supply operation split-supply operation 8-MSOP MSOP package family surface-mount technology industrial sensor conditioning current-shunt monitoring active filtering battery monitoring RoHS REACH AEC-Q100
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें