LM2904ADMG - Dual 26V Low-Power Op Amp | onsemi
N.º da peça: LM2904ADMG ✓ AtivoLM2904ADMG Visão geral
An operational amplifier is an analog signal-processing IC that uses high open-loop gain to amplify the difference between two input voltages. The LM2904 family belongs to the broader hierarchy of voltage-feedback operational amplifiers, analog amplifiers, and integrated signal-chain devices. Its common-mode capability makes it useful when signals approach the lower supply rail, while dual integration reduces board area in circuits requiring two independent amplifier channels.
Key operating characteristics include a low-power architecture, a 3 V to 26 V supply-voltage capability, and a slew rate of 0.6 V/µs. The 8-MSOP package provides a compact surface-mount option for industrial and embedded equipment. Its specified temperature range supports applications across extended commercial and industrial environments. Designers should verify gain-bandwidth, input-bias-current, output-current, noise, and input-offset parameters against their operating conditions before finalizing a high-impedance or precision design.
The LM2904ADMG uses the circuit design established for quad operational amplifiers, with two amplifiers per package. Its common-mode input voltage range extending toward ground or VEE is particularly useful in single-supply sensor interfaces, transimpedance stages, filters, and low-level signal amplifiers. The split-supply option permits operation around a zero-volt reference, while single-supply operation simplifies portable and industrial control systems.
Typical applications include current monitoring, sensor conditioning, audio preamplification, active filtering, and general-purpose analog signal processing. In a current-sensing application, the device can amplify the voltage developed across a low-value shunt while operating from a split supply. In a sensor interface, the common-mode range allows closer proximity to the lower rail than a conventional bipolar input amplifier. Input and output stability should be checked with the external resistor and capacitance values used in the final circuit.
A key design consideration is power-supply decoupling. Place a suitable bypass capacitor close to the supply pins and route return current through a low-impedance ground path. Avoid excessive output loading and confirm that the selected feedback network preserves the required gain-bandwidth and phase-margin behavior. For AC-coupled inputs, add suitable input bias-current compensation when source resistance is high.
This page combines the LM2904ADMG electrical identity, package and temperature information with replacement guidance, comparison parameters, and practical design considerations. It also identifies which replacement candidates preserve the 8-MSOP footprint and where application-specific validation remains necessary.
Alternativas drop-in para LM2904ADMG — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
LM2904ADM
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
LM2904ADMG Classificações máximas e características elétricas
| Amplifier Type | General-purpose operational amplifier |
| Number of Channels | 2 channels |
| Supply Voltage Range | 3 V to 26 V |
| Common-Mode Input Range | Extends to ground or VEE |
| Supply Configuration | Single supply or split supply |
| Slew Rate | 0.6 V/µs |
| Faixa de temperatura de operação | -40°C to +105°C |
| Encapsulamento | 8-MSOP, 3.00 mm width |
| Tipo de montagem | Surface mount |
| Packaging | Tape and reel |
Configuração de pinos do LM2904ADMG
| Pino 1 | OUT1 — Output of amplifier channel 1 |
| Pino 2 | IN1- — Inverting input of amplifier channel 1 |
| Pino 3 | IN1+ — Non-inverting input of amplifier channel 1 |
| Pino 4 | V- — Negative supply connection |
| Pino 5 | IN2+ — Non-inverting input of amplifier channel 2 |
| Pino 6 | IN2- — Inverting input of amplifier channel 2 |
| Pino 7 | OUT2 — Output of amplifier channel 2 |
| Pino 8 | V+ — Positive supply connection |
Aplicações típicas
LM2904ADMG é adequado para 6 aplicaçãos: Industrial Sensor Signal Conditioning, Current-Shunt Monitoring, Audio Preamplification, Active Filter and Equalization, Battery-Powered Monitoring, Portable Instrumentation Front End.
Industrial Sensor Signal Conditioning
The LM2904ADMG fits low-level industrial sensor conditioning because it provides two amplifier channels, a 3 V to 26 V supply range, and a common-mode input range extending toward ground or VEE. Place one channel around the sensor or bridge output and use the second for gain or filtering. The -40°C to +105°C specification suits extended industrial environments. Designers should verify the actual input offset, bias current, output swing, noise, and stability against the selected sensor impedance. A single supply is practical when the signal remains within the common-mode range, while split supplies allow operation around a zero-volt reference for bipolar sensor signals.
Recomendado
Current-Shunt Monitoring
The LM2904ADMG is suitable for amplifying the small differential voltage generated by a current-sense shunt while keeping the circuit compact. Two channels can monitor positive and negative portions of a bipolar waveform, or one channel can amplify the shunt signal while the other provides offset or filtering. Its common-mode input capability extending toward ground or VEE helps when the shunt voltage is close to the lower supply rail. Confirm the common-mode range, input offset, gain error, and output drive at the operating voltage. Decouple the supply pins locally and use a feedback layout that preserves the amplifier’s stability with the shunt and routing capacitance.
Recomendado
Audio Preamplification
The LM2904ADMG can provide basic audio preamplification in low-cost analog signal chains because it combines two channels with a 0.6 V/µs slew rate and a supply range up to 26 V. One channel can amplify a microphone or line-level source while the second supports volume control, tone shaping, or buffering. The common-mode range extending toward ground or VEE is useful in single-supply microphone circuits where the input lies close to the lower rail. Input-bias-current compensation, output loading, and output-swing headroom should be evaluated for the source impedance and channel configuration. Keep input routing short and connect the return path directly to the device ground reference.
Recomendado
Active Filter and Equalization
The LM2904ADMG is applicable to first-order active filters and equalization networks that operate within its bandwidth and slew-rate limits. Its dual configuration supports a two-pole filter using one amplifier per section or permits a signal-conditioning stage followed by an output filter. The 3 V to 26 V operating range supports portable, industrial-control, and higher-voltage analog systems. Because a general-purpose amplifier is not optimized for very high frequency or extremely low noise, calculate the gain-bandwidth margin, phase margin, and large-signal slew requirement for the target filter. Place compensation capacitors and feedback components close to their associated pins to minimize parasitic feedback effects.
Recomendado
Battery-Powered Monitoring
The LM2904ADMG can monitor and control low-voltage battery systems when the selected supply remains within its 3 V to 26 V operating range. Its low-power design and common-mode input range extending toward ground or VEE are useful for battery-voltage sensing and threshold detection when the signal approaches the lower rail. The second channel can monitor another sensor or supervise a control threshold. Calculate the maximum supply current for the battery budget and verify that the output can reach the required logic levels. Use a local supply bypass capacitor, minimize leakage into high-impedance sensing nodes, and confirm the complete operating-current budget across temperature and production tolerances.
Recomendado
Portable Instrumentation Front End
The LM2904ADMG suits compact instrumentation front ends that need two general-purpose amplifier channels within a 3 V to 26 V supply envelope. One channel can condition a transducer output while the other buffers a reference or drives an analog-to-converter input. The 8-MSOP package reduces PCB footprint, while the -40°C to +105°C rating supports equipment expected to operate across industrial temperature ranges. Check the input bias current when working with high-source-impedance sensors, and ensure that the ADC input range is compatible with the amplifier’s output swing. Maintain a compact ground return around the two channels and use separate routing where one amplifier handles a high-gain signal and the other handles a faster or noisier path.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para LM2904ADMG — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
For replacement work, LM2904ADM is the closest same-family 8-MSOP candidate identified, but the exact ordering suffix and packaging format should be confirmed before approval. Use a quad amplifier such as LM324KAPWR when four channels are needed, or LM2902-family parts when their lower-power characteristics better match the design. Select a precision or high-speed amplifier instead when input offset, noise, bandwidth, or slew-rate requirements exceed the capabilities of this general-purpose device.
Comparação com alternativas
| Parâmetro | Este produto | LM2904ADM |
|---|---|---|
| Package | 8-MSOP | 8-MSOP |
| Brand | onsemi | onsemi |
| Number of Channels | 2 | 2 |
| Supply Voltage Range | 3 V to 26 V | 3 V to 26 V |
| Slew Rate | 0.6 V/µs | 0.6 V/µs |
| Operating Temperature Range | -40°C to +105°C | -40°C to +105°C |
| Common-Mode Input Range | Extends to ground or VEE | Extends to ground or VEE |
| Supply Configuration | Single supply or split supply | Single supply or split supply |
| Amplifier Type | General-purpose | General-purpose |
| Mounting Type | Surface mount | Surface mount |
Principais diferenciais
- Combines two amplifier channels in one compact package (vs LM324KAPWR)
- Supports a broad supply-voltage operating range (vs LM2902KPWR)
- Common-mode input capability extends toward the lower rail (vs LM2902MTX)
Notas de projeto
Place the supply bypass capacitor directly between the positive and negative supply pins, with the ground connection following the shortest practical path. Keep input and feedback traces away from the supply and output nets, particularly when a high-value feedback resistor creates a sensitive high-impedance node. The 8-MSOP footprint is compact, so adequate land geometry and assembly clearance remain important even though the package offers limited pin pitch.
Do not assume that the common-mode input range extending toward ground or VEE permits unrestricted operation at the lower rail. Check the complete input and output voltage limits from the manufacturer datasheet for the selected supply, including output-swing headroom. In single-supply designs, verify the input offset and bias-current contribution because those errors can dominate a low-level sensor signal even though the amplifier is operating within its nominal supply range.
Calculate the maximum large-signal input frequency using the required output amplitude and the specified 0.6 V/µs slew rate. If slew-rate distortion appears before the intended bandwidth limit is reached, reduce signal amplitude, increase the supply voltage where allowed, or select a faster amplifier. Also check the gain-bandwidth product and phase margin against the feedback network, including the capacitance introduced by PCB traces and connected test equipment.
For dual-supply operation, connect the midpoint ground and bypass each supply rail independently. The negative supply must remain within its absolute maximum and must not be used as a signal-ground substitute. Evaluate total amplifier dissipation across both channels under worst-case voltage and output conditions, and ensure the PCB thermal design can remove that heat without forcing the junction above its allowable limit.
Informações de conformidade
The available product information does not establish RoHS, REACH, halogen-free, conflict-minerals, or AEC-Q100 status. This operational amplifier is not presented as an automotive-qualified device.