LM293DRG3 - Dual Differential Comparator | Texas Instruments
MPN: LM293DRG3 ✓ सक्रियLM293DRG3 अवलोकन
A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when the difference crosses a defined threshold. The LM293 belongs to the comparator hierarchy, which also includes differential comparators and open-collector interface comparators. These devices bridge low-level analog sensing and digital control by converting an analog condition into a logic-readable result.
The LM293DRG3 offers two independent comparators, rail-to-rail output behavior, and low output saturation voltage. Its open-collector outputs permit wired-AND connections and external pull-up selection, making the device adaptable to different logic families and voltage domains. The common-mode input range including ground is particularly useful in battery-powered and industrial systems powered from a single rail.
Each channel compares a non-inverting input with an inverting input and uses open-drain output transistors to indicate the polarity of the differential voltage. The outputs can sink current while remaining in a high-impedance state when inactive. Because the output stage does not actively drive a high voltage, pull-up resistors are required when a logic-high level is needed. Differential input protection and common-mode limits must be respected during fault conditions.
Typical uses include monitoring a sensor output, detecting supply thresholds, comparing an analog measurement with a reference, generating window-limit signals, and supporting industrial control logic. Two independent channels allow related threshold functions to be implemented in one package, reducing component count while preserving separate input and output isolation.
Designers should select pull-up resistors to suit the destination logic voltage and sink-current budget, connect an unused comparator input to a defined valid potential, and verify input and output behavior across the full supply range. This page combines ordering information, package details, drop-in replacement guidance, comparison data, and practical design guidance for faster component selection.
के लिए ड्रॉप-इन विकल्प LM293DRG3 — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस सीरीज़ के वेरिएंट
समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं LM293DRG3 (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Package, Mounting Type, Output Type, Common-Mode Input Range, Number of Channels.
LM393D
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित✗ स्टॉक में नहीं
$0.11 / यूनिट
डेटाशीट देखें →LM2903D
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापितकीमत के लिए संपर्क करें
डेटाशीट देखें →LM2904PWR
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापितकीमत के लिए संपर्क करें
डेटाशीट देखें →LM2902N/PB
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापितकीमत के लिए संपर्क करें
डेटाशीट देखें →LM293D
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →LM293DRG3 Maximum Ratings और Electrical Characteristics
| Comparator Type | Dual differential voltage comparator |
| Number of Channels | 2 channels |
| Supply Voltage, Single | ±15 V |
| Total Supply Voltage | 30 V |
| Differential Input Voltage Range | ±38 V |
| Common-Mode Input Range | Includes ground |
| आउटपुट प्रकार | Open-collector, open-drain |
| Output Rail-to-Rail | Yes |
| Output Logic Compatibility | TTL, MOS, and CMOS |
| पैकेज | 8-pin SOIC, 3.90 mm width |
| माउंटिंग प्रकार | Surface mount |
| Shipping Format | Tape and reel |
| Automotive Qualification | Not an AEC-Q100-qualified variant |
LM293DRG3 पिन कॉन्फ़िगरेशन
| पिन 1 | OUT1 — Open-collector output of comparator channel 1 |
| पिन 2 | IN1- — Inverting input of comparator channel 1 |
| पिन 3 | IN1+ — Non-inverting input of comparator channel 1 |
| पिन 4 | GND — Ground reference |
| पिन 5 | IN2+ — Non-inverting input of comparator channel 2 |
| पिन 6 | IN2- — Inverting input of comparator channel 2 |
| पिन 7 | OUT2 — Open-collector output of comparator channel 2 |
| पिन 8 | VCC — Positive supply voltage |
सामान्य अनुप्रयोग
LM293DRG3 के लिए उपयुक्त है 6 अनुप्रयोगs: Industrial Sensor Threshold Detection, Power Supply Overvoltage Detection, Battery Voltage Window Monitoring, Motor and Actuator Limit Detection, Window Comparator for Control Systems, TTL and CMOS Logic Interfacing.
Industrial Sensor Threshold Detection
The LM293DRG3 is appropriate for comparing a conditioned sensor signal against a reference voltage in industrial monitoring equipment. Its common-mode input range includes ground, which supports sensors operating near 0 V, while the differential input range can extend to ±38 V. Two independent channels can implement upper and lower thresholds or monitor two related inputs. Open-collector outputs can drive a pull-up to the logic voltage used by a controller. Designers should confirm the input offset and bias current against the smallest sensor transition that must be detected.
अनुशंसित
Power Supply Overvoltage Detection
The LM293DRG3 can monitor a divided supply rail and assert an open-collector fault signal when the voltage crosses a threshold. A resistor divider scales the monitored rail into the comparator input range, while the differential input capability of up to ±38 V helps accommodate transient conditions within the device rating. Because the output is open collector, it can be pulled up to an isolated or lower-voltage system domain. Threshold accuracy depends on reference quality, resistor tolerance, input offset, and noise around the switching point.
अनुशंसित
Battery Voltage Window Monitoring
The LM293DRG3 is suitable for single-supply battery monitoring where one channel detects a lower threshold and the other detects an upper threshold. Its common-mode range includes ground, which is important when the battery voltage approaches the supply rail and is divided down toward zero volts. The two open-collector outputs can be wired together to create a simple window-fault indication, or pulled up separately for digital status inputs. Select divider values so normal operation stays away from the absolute input limits and review the voltage difference between each switching threshold.
अनुशंसित
Motor and Actuator Limit Detection
The LM293DRG3 can compare a scaled position or current-sense signal with upper and lower limits in motor-control and actuator systems. Its two independent channels provide separate inverting and non-inverting inputs for complementary limit detection, while the differential input range of ±38 V offers margin for transients when the sensed signal is properly scaled. Open-collector outputs can drive a pull-up or participate in a wired fault bus. The design must include protection against reverse polarity, excessive transient voltage, and input conditions outside the common-mode range.
अनुशंसित
Window Comparator for Control Systems
The LM293DRG3 implements a two-channel window comparator when each independent channel compares a signal against an upper or lower reference. Its open-collector outputs are useful for driving discrete logic, relay drivers, or digital isolator inputs because the pull-up voltage can be selected independently from the comparator supply. The 30 V total-supply capability supports industrial rails, while the common-mode range reaching ground simplifies single-supply implementations. When both outputs are connected to a common pull-up, verify that the wired-AND fault state cannot exceed the sink-current limit of either channel.
अनुशंसित
TTL and CMOS Logic Interfacing
The LM293DRG3 acts as an analog-to-logic interface when a sensor or divider network must drive a digital input. Its open-collector output sinks current from an external pull-up and can be referenced to the voltage required by TTL, MOS, or CMOS logic. This avoids tying the logic-high level to the comparator supply and permits level translation between domains. Choose the pull-up resistor for the required rise time and sink current, and account for input leakage, bus capacitance, and the output saturation specification when the receiving device has CMOS-level sensitivity.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा LM293DRG3 — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | LM393D | LM2903D | LM2904PWR | LM2902N/PB | LM293D |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | onsemi | Texas Instruments | STMicroelectronics |
| Package | 8-pin SOIC | 8-pin SOIC - same package | 8-pin SOIC - same package | 8-pin SOIC - same package | 8-pin SOIC - same package | 8-pin SOIC - same package |
| Comparator Channels | 2 | 2 | 2 | 2 | 2 | 2 |
| Output Type | Open-collector, open-drain | Open-collector, open-drain | Open-collector, open-drain | Open-collector, open-drain | Open-collector, open-drain | Open-collector, open-drain |
मुख्य विशेषताएँ
- Two independent differential channels with open-collector outputs (बनामLM2904PWR)
- Common-mode operation down to ground supports single-rail sensing (बनामLM393D)
- Wide differential input capability (बनामLM293D)
- Logic-level flexibility through externally selected pull-ups (बनामLM2902N/PB)
डिज़ाइन नोट्स
Do not assume an open-collector output will produce a valid logic-high voltage without an external pull-up. Connect a resistor from each output to the required logic rail, and ensure that the worst-case low-state sink current from all connected inputs does not exceed the output limit. When multiple outputs share one pull-up, their individual saturation voltages and leakage currents affect the combined low-level voltage and should be checked together.
Keep comparator input traces short and away from high-current switching nodes where practical. Use a stable reference divider with low noise and adequate bypass capacitance, and avoid routing the reference and signal traces in parallel with power-current paths. A small amount of hysteresis can be introduced with positive feedback when the input source has excessive noise, but the resistor network must remain within the input bias-current and common-mode limits.
Place the device to match the standard 8-pin SOIC footprint and follow the manufacturer pin numbering around the package. Connect the ground pin to a low-impedance ground plane and route output pull-up resistors close to the corresponding open-collector pins to minimize exposed trace length. For applications with sensitive analog inputs, separate the input network from digital pull-up currents and provide a nearby ground-return path.
Check the input pins against both the common-mode range and the maximum differential input rating throughout startup, shutdown, and fault conditions. The LM293 family supports a wide differential range, but that rating does not remove the need to limit external voltage. Add series resistance or clamps where a sensor or transient source can exceed the comparator's input limits. The 30 V total-supply capability should not be treated as permission to exceed the absolute maximum rating.
If only one comparator channel is used, do not leave its input pins floating. Configure the unused channel according to the manufacturer guidance so its inputs remain at defined potentials and its output cannot interfere with the circuit. Also verify that the chosen pull-up voltage is compatible with the comparator output's allowed voltage range; tying an output to an excessive pull-up rail can damage the device even when the normal input signals are correct.
अनुपालन जानकारी
The LM293DRG3 is an industrial-grade dual comparator rather than an AEC-Q100-qualified automotive ordering option. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current manufacturer product documentation.