Texas Instruments

LM293DRG3 - Dual Differential Comparator | Texas Instruments

Teilenummer: LM293DRG3 ✓ Aktiv
±15 V Vdss 8-pin SOIC, 3.90 mm width Package
MOQ: 1 |

LM293DRG3 Übersicht

The Texas Instruments LM293DRG3 is a dual differential voltage comparator in an 8-pin SOIC package. The device contains two independent comparison channels, supports ±15 V single-ended or 30 V total supply operation, and provides open-collector, open-drain outputs compatible with TTL, MOS, and CMOS logic. Its common-mode input range includes ground, allowing operation from a single positive supply, while the differential input range can extend to ±38 V.

A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when the difference crosses a defined threshold. The LM293 belongs to the comparator hierarchy, which also includes differential comparators and open-collector interface comparators. These devices bridge low-level analog sensing and digital control by converting an analog condition into a logic-readable result.

The LM293DRG3 offers two independent comparators, rail-to-rail output behavior, and low output saturation voltage. Its open-collector outputs permit wired-AND connections and external pull-up selection, making the device adaptable to different logic families and voltage domains. The common-mode input range including ground is particularly useful in battery-powered and industrial systems powered from a single rail.

Each channel compares a non-inverting input with an inverting input and uses open-drain output transistors to indicate the polarity of the differential voltage. The outputs can sink current while remaining in a high-impedance state when inactive. Because the output stage does not actively drive a high voltage, pull-up resistors are required when a logic-high level is needed. Differential input protection and common-mode limits must be respected during fault conditions.

Typical uses include monitoring a sensor output, detecting supply thresholds, comparing an analog measurement with a reference, generating window-limit signals, and supporting industrial control logic. Two independent channels allow related threshold functions to be implemented in one package, reducing component count while preserving separate input and output isolation.

Designers should select pull-up resistors to suit the destination logic voltage and sink-current budget, connect an unused comparator input to a defined valid potential, and verify input and output behavior across the full supply range. This page combines ordering information, package details, drop-in replacement guidance, comparison data, and practical design guidance for faster component selection.

Drop-in-Alternativen für LM293DRG3 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

Varianten dieser Serie

Modelle derselben Serie, die drop-in-kompatibel sind mit LM293DRG3 (gleiche Bauform und Footprint) – abweichend in Package, Mounting Type, Output Type, Common-Mode Input Range, Number of Channels.

Texas Instruments
Mounting Type: Through-hole
Texas Instruments
Package: 8-pin SOIC
Output Type: Open-collector
Vergleichen mit LM293DRG3 →
Texas Instruments
Package: 8-TSSOP, 4.40 mm width
Vergleichen mit LM293DRG3 →
Texas Instruments
Package: 8-SOIC
Vergleichen mit LM293DRG3 →
Texas Instruments
Package: SOIC-8 (D), 3.90 mm body width
Output Type: Open-Collector
Common-Mode Input Range: 0 V to VCC − 1.5 V
Vergleichen mit LM293DRG3 →

LM393D

✅ Drop-In ⚠️ Spezifikationen ungeprüft
Texas Instruments
📦 8-pin SOIC
Texas Instruments · LM393D · Dual Differential Comparator · 2 · Open-Collector · 2 V to 36 V · ±1 V to ±18 V · 1 mV

✗ Nicht auf Lager

$0.11 / Stück

Datenblatt ansehen →

LM2903D

✅ Drop-In ⚠️ Spezifikationen ungeprüft
Texas Instruments
📦 8-pin SOIC
Dual differential comparator · 2 channels · 2 V to 36 V · Open-collector · 300 ns · 8-pin SOIC · Surface mount · -40 °C to +125 °C

Preis auf Anfrage

Datenblatt ansehen →

LM2904PWR

✅ Drop-In ⚠️ Spezifikationen ungeprüft
Texas Instruments
📦 8-pin SOIC
2 circuits · Dual general-purpose operational amplifier · 26 V · 700 kHz · 0.7 mA · Independent of supply voltage · Single supply or split supply · Includes ground

Preis auf Anfrage

Datenblatt ansehen →

LM2902N/PB

✅ Drop-In ⚠️ Spezifikationen ungeprüft
Texas Instruments
📦 8-pin SOIC
4 · 26 V · 1 MHz · Quad general-purpose operational amplifier · Independent, high-gain, internally frequency-compensated · Single-supply operation · 14-pin DIP · DIP-14

Preis auf Anfrage

Datenblatt ansehen →

LM293D

✅ Drop-In
Texas Instruments
📦 8-pin SOIC
Dual differential comparator · Two independent comparators · Open-collector, open-drain · Rail-to-rail · Single supply or split supply

Preis auf Anfrage

Datenblatt ansehen →

LM293DRG3 Grenzwerte & elektrische Eigenschaften

Comparator Type Dual differential voltage comparator
Number of Channels 2 channels
Supply Voltage, Single ±15 V
Total Supply Voltage 30 V
Differential Input Voltage Range ±38 V
Common-Mode Input Range Includes ground
Ausgangstyp Open-collector, open-drain
Output Rail-to-Rail Yes
Output Logic Compatibility TTL, MOS, and CMOS
Gehäuse 8-pin SOIC, 3.90 mm width
Montageart Surface mount
Shipping Format Tape and reel
Automotive Qualification Not an AEC-Q100-qualified variant

LM293DRG3 Pin-Konfiguration

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
Pin 1 OUT1 — Open-collector output of comparator channel 1
Pin 2 IN1- — Inverting input of comparator channel 1
Pin 3 IN1+ — Non-inverting input of comparator channel 1
Pin 4 GND — Ground reference
Pin 5 IN2+ — Non-inverting input of comparator channel 2
Pin 6 IN2- — Inverting input of comparator channel 2
Pin 7 OUT2 — Open-collector output of comparator channel 2
Pin 8 VCC — Positive supply voltage

Typische Anwendungen

LM293DRG3 ist geeignet für 6 Anwendungs: Industrial Sensor Threshold Detection, Power Supply Overvoltage Detection, Battery Voltage Window Monitoring, Motor and Actuator Limit Detection, Window Comparator for Control Systems, TTL and CMOS Logic Interfacing.

🏭

Industrial Sensor Threshold Detection

The LM293DRG3 is appropriate for comparing a conditioned sensor signal against a reference voltage in industrial monitoring equipment. Its common-mode input range includes ground, which supports sensors operating near 0 V, while the differential input range can extend to ±38 V. Two independent channels can implement upper and lower thresholds or monitor two related inputs. Open-collector outputs can drive a pull-up to the logic voltage used by a controller. Designers should confirm the input offset and bias current against the smallest sensor transition that must be detected.

⚡

Power Supply Overvoltage Detection

The LM293DRG3 can monitor a divided supply rail and assert an open-collector fault signal when the voltage crosses a threshold. A resistor divider scales the monitored rail into the comparator input range, while the differential input capability of up to ±38 V helps accommodate transient conditions within the device rating. Because the output is open collector, it can be pulled up to an isolated or lower-voltage system domain. Threshold accuracy depends on reference quality, resistor tolerance, input offset, and noise around the switching point.

🔋

Battery Voltage Window Monitoring

The LM293DRG3 is suitable for single-supply battery monitoring where one channel detects a lower threshold and the other detects an upper threshold. Its common-mode range includes ground, which is important when the battery voltage approaches the supply rail and is divided down toward zero volts. The two open-collector outputs can be wired together to create a simple window-fault indication, or pulled up separately for digital status inputs. Select divider values so normal operation stays away from the absolute input limits and review the voltage difference between each switching threshold.

🔧

Motor and Actuator Limit Detection

The LM293DRG3 can compare a scaled position or current-sense signal with upper and lower limits in motor-control and actuator systems. Its two independent channels provide separate inverting and non-inverting inputs for complementary limit detection, while the differential input range of ±38 V offers margin for transients when the sensed signal is properly scaled. Open-collector outputs can drive a pull-up or participate in a wired fault bus. The design must include protection against reverse polarity, excessive transient voltage, and input conditions outside the common-mode range.

📟

Window Comparator for Control Systems

The LM293DRG3 implements a two-channel window comparator when each independent channel compares a signal against an upper or lower reference. Its open-collector outputs are useful for driving discrete logic, relay drivers, or digital isolator inputs because the pull-up voltage can be selected independently from the comparator supply. The 30 V total-supply capability supports industrial rails, while the common-mode range reaching ground simplifies single-supply implementations. When both outputs are connected to a common pull-up, verify that the wired-AND fault state cannot exceed the sink-current limit of either channel.

🔌

TTL and CMOS Logic Interfacing

The LM293DRG3 acts as an analog-to-logic interface when a sensor or divider network must drive a digital input. Its open-collector output sinks current from an external pull-up and can be referenced to the voltage required by TTL, MOS, or CMOS logic. This avoids tying the logic-high level to the comparator supply and permits level translation between domains. Choose the pull-up resistor for the required rise time and sink current, and account for input leakage, bus capacitance, and the output saturation specification when the receiving device has CMOS-level sensitivity.

What is the LM293DRG3?
The LM293DRG3 is a Texas Instruments dual differential voltage comparator with two independent comparison channels in an 8-pin SOIC package. According to the manufacturer product page, the LM293 is an industrial-grade device whose open-collector outputs are compatible with TTL, MOS, and CMOS logic. It supports ±15 V or 30 V total supply operation and can compare signals whose differential voltage reaches ±38 V.
Where can I download the LM293DRG3 datasheet PDF?
The official LM293DRG3 documentation is available through the Texas Instruments LM293 product page and the manufacturer datasheet link on this page. The family documentation covers the LM193, LM293, LM2903, LM393, and LM2903B dual-comparator families. Use the pin-description table and electrical-characteristics tables for channel assignments, supply limits, input ranges, output behavior, and ordering information.
Where can I find the LM293DRG3 pinout?
The LM293DRG3 uses an 8-pin SOIC pinout with two independent differential comparator channels. Pins 1 and 7 are the respective open-collector outputs, pins 2 and 6 are the inverting inputs, pins 3 and 5 are the non-inverting inputs, pin 4 is ground, and pin 8 is the positive supply. Confirm assignments against the manufacturer pin-description table before finalizing PCB artwork.
What supply voltage does the LM293DRG3 operate from?
The LM293DRG3 supports operation up to ±15 V, equivalent to 30 V total across the supply pins. According to the Texas Instruments LM293 product page, its common-mode input voltage range includes ground, while the differential input voltage range can equal ±38 V. Actual design limits must account for input and output protection behavior at the supply extremes.
Does the LM293DRG3 work with a single 5 V supply?
The LM293DRG3 can operate from a single positive supply because its common-mode input range includes ground. The outputs are open-collector and require an external pull-up when a digital high level is required. In a 5 V system, the pull-up can be connected to 5 V when the receiving circuit accepts TTL- or CMOS-compatible signaling, subject to the device's output-current limits.
Why does the LM293DRG3 output need a pull-up resistor?
Each LM293 output uses an open-collector transistor that actively sinks current but does not actively source a logic-high current. A pull-up resistor establishes the high output voltage and allows multiple open-collector outputs to be wired together. Choose the resistor to balance rise time, power consumption, bus capacitance, and the maximum sink current required by the connected CMOS or MOS input.
What is the difference between LM293DRG3 and LM293D?
The LM293DRG3 and LM293D are ordering variants associated with the same Texas Instruments LM293 dual-comparator family and the same 8-pin SOIC footprint. The principal practical differences can include grade, packaging, and order-code details, while the functional comparator characteristics remain within the LM293 family definition. Verify the exact suffix against the manufacturer ordering table before substituting one for the other.
LM293DRG3 vs LM2904PWR - which comparator should I choose?
Choose the LM293DRG3 when your design is tied to the LM293 family and its specified differential-comparator behavior; choose LM2904PWR when the LM2904 family's electrical requirements are appropriate. Both are dual open-collector comparator solutions, but input offsets, bias currents, common-mode limits, and qualification details can differ. Compare those manufacturer parameters against the sensing node before making a footprint-level substitution.
When should I choose LM293DRG3 over another dual comparator?
Choose LM293DRG3 when you need two independent differential channels, operation from a single supply with a common-mode range reaching ground, and open-collector outputs that support pull-up or wired-AND arrangements. It is especially suitable for industrial sensing and threshold detection. Select another comparator when its input offset, bias current, response time, output type, or automotive qualification better matches the application.
Is the LM293DRG3 suitable for industrial sensor monitoring?
The LM293DRG3 is suitable for industrial sensor monitoring when the sensed signal remains inside its input ratings and a valid reference is available. Its common-mode range includes ground, its differential input capability reaches ±38 V, and the open-drain outputs can interface with industrial digital logic through suitable pull-up networks. The LM293 is identified by Texas Instruments as an industrial-grade dual comparator.
What can replace the LM293DRG3?
A direct replacement must use the same 8-pin SOIC footprint, preserve the two-channel differential-comparator arrangement, and retain compatible input and output behavior. Closest candidates include LM393D, LM2903D, LM2904PWR, and STMicroelectronics LM293D, subject to verification of electrical limits and qualification. Do not treat a different package or a rail-to-rail push-pull output device as a drop-in replacement.
Is the STMicroelectronics LM293D a drop-in replacement for LM293DRG3?
The STMicroelectronics LM293D is a strong footprint candidate because it is also a dual differential comparator in an 8-pin SOIC package with open-collector outputs. Before fitting it, compare input offset voltage, input bias current, common-mode range, supply current, output saturation, response time, and temperature grade against the Texas Instruments LM293DRG3. Pin compatibility alone does not guarantee identical precision or system behavior.
Where can I buy LM293DRG3 and check current price and lead time?
Use the Request a Quote form on this page to request the current LM293DRG3 price, stock position, minimum order quantity, and lead time for the exact 8-pin SOIC ordering code. The request should identify the required quantity and shipment destination so the quotation can reflect the appropriate packaging and logistics. Inventory and commercial terms can change, so confirm them when placing the order.
What are the key specifications of LM293DRG3 that engineers should know?
The key LM293DRG3 specifications are: two independent differential comparator channels, ±15 V or 30 V total supply capability, a common-mode input range that includes ground, differential input capability up to ±38 V, and open-collector outputs compatible with TTL, MOS, and CMOS. The device is offered in an 8-pin SOIC and is identified by Texas Instruments as industrial grade.
How should pull-up resistors and unused inputs be handled for LM293DRG3?
Fit a pull-up resistor on each open-collector output that must drive a valid logic-high state, and verify that the resistor does not exceed the output sink-current capability. If either comparator channel is unused, connect its non-inverting input to ground through a suitable resistor and its inverting input to ground so the unused channel remains in a defined state. Follow the manufacturer's recommended-input and unused-circuit guidance.

Technische Referenzdaten für LM293DRG3 – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose the LM293DRG3 for a two-channel industrial threshold-detection design that needs an 8-pin SOIC footprint, a common-mode input range extending to ground, and open-collector outputs. LM393D is appropriate when its offset, bias-current, and timing characteristics better match the sensing circuit. LM2903D and LM2904PWR remain useful alternatives within related dual-comparator families, but their exact electrical limits should be compared before substitution. LM2902N/PB can suit broader dual-comparator signal conditioning, while the STMicroelectronics LM293D provides a closely related SOIC alternative. For every choice, verify the power rails, input protection requirements, allowable common-mode range, pull-up voltage, output sink current, temperature grade, and availability of the exact ordering suffix before releasing the PCB.

Vergleich mit Alternativen

Parameter Dieses Produkt LM393D LM2903D LM2904PWR LM2902N/PB LM293D
Brand Texas Instruments Texas Instruments Texas Instruments onsemi Texas Instruments STMicroelectronics
Package 8-pin SOIC 8-pin SOIC - same package 8-pin SOIC - same package 8-pin SOIC - same package 8-pin SOIC - same package 8-pin SOIC - same package
Comparator Channels 2 2 2 2 2 2
Output Type Open-collector, open-drain Open-collector, open-drain Open-collector, open-drain Open-collector, open-drain Open-collector, open-drain Open-collector, open-drain

Wichtigste Unterscheidungsmerkmale

  • Two independent differential channels with open-collector outputs (vs. LM2904PWR)
  • Common-mode operation down to ground supports single-rail sensing (vs. LM393D)
  • Wide differential input capability (vs. LM293D)
  • Logic-level flexibility through externally selected pull-ups (vs. LM2902N/PB)

Designhinweise

Do not assume an open-collector output will produce a valid logic-high voltage without an external pull-up. Connect a resistor from each output to the required logic rail, and ensure that the worst-case low-state sink current from all connected inputs does not exceed the output limit. When multiple outputs share one pull-up, their individual saturation voltages and leakage currents affect the combined low-level voltage and should be checked together.

Keep comparator input traces short and away from high-current switching nodes where practical. Use a stable reference divider with low noise and adequate bypass capacitance, and avoid routing the reference and signal traces in parallel with power-current paths. A small amount of hysteresis can be introduced with positive feedback when the input source has excessive noise, but the resistor network must remain within the input bias-current and common-mode limits.

Place the device to match the standard 8-pin SOIC footprint and follow the manufacturer pin numbering around the package. Connect the ground pin to a low-impedance ground plane and route output pull-up resistors close to the corresponding open-collector pins to minimize exposed trace length. For applications with sensitive analog inputs, separate the input network from digital pull-up currents and provide a nearby ground-return path.

Check the input pins against both the common-mode range and the maximum differential input rating throughout startup, shutdown, and fault conditions. The LM293 family supports a wide differential range, but that rating does not remove the need to limit external voltage. Add series resistance or clamps where a sensor or transient source can exceed the comparator's input limits. The 30 V total-supply capability should not be treated as permission to exceed the absolute maximum rating.

If only one comparator channel is used, do not leave its input pins floating. Configure the unused channel according to the manufacturer guidance so its inputs remain at defined potentials and its output cannot interfere with the circuit. Also verify that the chosen pull-up voltage is compatible with the comparator output's allowed voltage range; tying an output to an excessive pull-up rail can damage the device even when the normal input signals are correct.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

The LM293DRG3 is an industrial-grade dual comparator rather than an AEC-Q100-qualified automotive ordering option. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current manufacturer product documentation.

Daten verifiziert am: 2026-11-15 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

LM293DRG3 datasheet LM293DRG3 pinout LM293DRG3 datasheet pdf LM293DRG3 equivalent LM293DRG3 replacement LM293DRG3 cross reference LM293DRG3 price LM293DRG3 stock Texas Instruments LM293DRG3 LM293DRG3 vs LM293D LM293DRG3 SOIC footprint LM293DRG3 application circuit LM293DRG3 open collector output LM293 dual comparator specifications

Verwandte Bauteile & Begriffe

Texas Instruments LM293DRG3 LM293 LM393D LM2903D LM2904PWR LM2902N/PB STMicroelectronics LM293D dual differential comparator voltage comparator open-collector comparator analog integrated circuit semiconductor common-mode input voltage differential input voltage open-drain output TTL MOS logic CMOS logic SOIC-8 surface mount industrial grade wired-AND sensor threshold detection
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen