LM324ADG - Quad Op-Amp 1MHz 0.6V/us SOIC-14 | onsemi
MPN: LM324ADG ✓ सक्रियLM324ADG अवलोकन
An operational amplifier is a high-gain voltage amplifier with differential inputs and a single-ended output, the foundational building block of the analog signal chain. Within the amplifier hierarchy, the LM324ADG belongs to the general-purpose, single-supply op-amp family, sitting above specialized precision, high-speed, and rail-to-rail amplifiers and below discrete transistor front ends in complexity. Quad op amps integrate four amplifiers on one die, sharing bias circuitry to save board space, cost, and power versus four single amplifiers.
Key features include true differential inputs valid at ground (the common-mode input range extends to the negative rail, an LM324 family signature), a wide supply range from 3.0 V to 32 V that covers 5 V, 12 V, 15 V, and 24 V rails, four amplifiers per package for dense multi-channel analog designs, and internally compensated unity-gain stability that removes the need for external frequency-compensation capacitors.
Architecturally, the LM324A uses bipolar NPN input stages with PNP common-emitter amplifiers and Class AB outputs. The 'A' grade tightens the input offset voltage specification to a 3 mV maximum. Because the output stage is not rail-to-rail, the output swings to within roughly 1.5 V of V+ at light load while reaching close to the negative rail - a characteristic engineers must budget for when using the full supply range.
Typical applications include transducer signal conditioning, DC gain blocks, active filters, comparators with hysteresis, summing amplifiers, and multi-channel industrial sensor interfaces, where the single-supply ground-sensing input and four-amplifier density directly reduce component count.
Design consideration: the common-mode input range stops about 1.5 V below the positive rail, so keep input signals at least that far from V+ to avoid phase inversion or distortion.
This page adds value beyond the manufacturer datasheet by consolidating drop-in alternatives, parameter comparison tables, and practical design notes in one place for sourcing and design engineers.
के लिए ड्रॉप-इन विकल्प LM324ADG — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस सीरीज़ के वेरिएंट
समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं LM324ADG (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Slew Rate, Amplifier Type, Operating Temperature Range, Gain-Bandwidth Product, Package.
MC3403DR
✅ ड्रॉप-इन✓ स्टॉक में
$0.4102 / यूनिट
डेटाशीट देखें →LM324ADR2G
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →TS974IDT
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →LM324ADT
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित📋 संदर्भ विकल्प (कैटलॉग में नहीं)
LM224ADG
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित📋 संदर्भ विकल्प (कैटलॉग में नहीं)
LM324ADG Maximum Ratings और Electrical Characteristics
| Amplifier Type | General Purpose |
| Number of Circuits | 4 |
| Gain Bandwidth Product | 1 MHz |
| Slew Rate | 0.6 V/us |
| Supply Voltage Range (Single) | 3 V to 32 V |
| Supply Voltage Range (Dual) | +/-1.5 V to +/-16 V |
| Input Offset Voltage (Max) | 3 mV |
| पैकेज / केस | 14-SOIC (0.154 in, 3.90 mm Width) |
| माउंटिंग प्रकार | Surface Mount |
| Packaging | Tube |
| Temperature Grade | Commercial |
| Unity Gain Stability | Yes (internally frequency compensated) |
| Product Series | LM324A (Single Supply Quad Operational Amplifiers) |
LM324ADG पिन कॉन्फ़िगरेशन
| पिन 1 | OUT1 — Output of amplifier 1 |
| पिन 2 | IN1- — Inverting input of amplifier 1 |
| पिन 3 | IN1+ — Non-inverting input of amplifier 1 |
| पिन 4 | V+ — Positive supply voltage |
| पिन 5 | IN2+ — Non-inverting input of amplifier 2 |
| पिन 6 | IN2- — Inverting input of amplifier 2 |
| पिन 7 | OUT2 — Output of amplifier 2 |
| पिन 8 | OUT3 — Output of amplifier 3 |
| पिन 9 | IN3- — Inverting input of amplifier 3 |
| पिन 10 | IN3+ — Non-inverting input of amplifier 3 |
| पिन 11 | VEE/GND — Negative supply or ground reference |
| पिन 12 | IN4+ — Non-inverting input of amplifier 4 |
| पिन 13 | IN4- — Inverting input of amplifier 4 |
| पिन 14 | OUT4 — Output of amplifier 4 |
सामान्य अनुप्रयोग
LM324ADG के लिए उपयुक्त है 6 अनुप्रयोगs: Transducer Signal Conditioning, DC Gain Blocks and Summing Amplifiers, Active Filters, Comparators with Hysteresis, Industrial Sensor Interfaces on 24V Rails, Consumer Audio Preamps and Mixers.
Transducer Signal Conditioning
The LM324ADG fits transducer signal conditioning because its common-mode input range extends down to the negative supply rail, allowing sensors such as thermistors, strain-gauge bridges, and photodiode outputs referenced to ground to be amplified directly without level shifting. With four amplifiers per SOIC-14 package, a multi-channel sensor board can implement per-channel gain stages with one device, cutting component count and cost. The 1 MHz gain-bandwidth product supports closed-loop gains of 10 to 100 with bandwidths of 10 kHz down to 1 kHz, adequate for most physical-parameter sensing where signal content sits well below audio frequencies. Place a gain-setting resistor network per channel and add a small feedback capacitor for stability with high-value resistors; the 0.6 V/us slew rate comfortably handles slow sensor transients without slewing distortion.
अनुशंसित
DC Gain Blocks and Summing Amplifiers
For DC gain blocks, the LM324ADG's 'A'-grade 3 mV maximum input offset voltage limits output error to offset multiplied by the closed-loop gain - for example, 300 mV of output offset at a gain of 100, which many industrial tolerance budgets accept without trimming. The quad integration lets one package build a complete summing junction plus buffer chain, with shared bias circuitry reducing quiescent current to roughly one-fifth of four discrete standard op amps. True differential inputs support standard inverting and non-inverting topologies from a single 3 V to 32 V rail, eliminating the negative supply in many designs. When computing accuracy, add resistor-network tolerance and bias-current errors on top of the 3 mV offset; use balanced source impedances at both inputs so bias currents cancel, a technique highlighted in the LM324 application guidance.
अनुशंसित
Active Filters
The LM324ADG implements Sallen-Key and multiple-feedback active filters for cutoff frequencies up to roughly 20 kHz, constrained by the 1 MHz gain-bandwidth product: at a unity-gain Sallen-Key stage, the Q error stays low when the cutoff frequency remains below about 1/20th of the GBW. Four amplifiers per SOIC-14 package allow a complete fourth-order filter - two cascaded second-order stages - from one device, ideal for anti-aliasing pre-filters and audio-band shaping in industrial controllers. The ground-sensing input range permits single-supply filter designs biased at mid-rail with simple resistor dividers. Note that the 0.6 V/us slew rate limits large-signal handling above the audio band, so keep filter outputs within a few volts of swing at higher frequencies to avoid slewing-induced distortion; add a post-filter buffer channel from the same package.
अनुशंसित
Comparators with Hysteresis
One LM324ADG channel works as a comparator with hysteresis using positive feedback resistors, and the quad package provides four independent threshold detectors in a single SOIC-14 footprint for multi-level battery monitoring, window comparators, and limit switches. Because the input common-mode range reaches the negative rail, thresholds referenced to ground are sensed directly, and the output pulling near ground drives logic and LED loads in single-supply systems. Note that this is a slow comparison path: with 0.6 V/us slew rate and 1 MHz GBW, response times sit in the microsecond range, so it is unsuitable for fast clock recovery or high-speed protection loops - use a dedicated comparator there. Add hysteresis of at least tens of millivolts via the feedback divider to prevent chatter from noisy sensor inputs near the threshold.
अनुशंसित
Industrial Sensor Interfaces on 24V Rails
Factory-floor systems commonly run 24 V single-supply rails, and the LM324ADG's 32 V maximum supply accepts this directly without a pre-regulator, simplifying interface boards for 4-20 mA current loops, proximity sensors, and level detectors. Four channels per package support multi-point monitoring - loop sense, scaling amplifier, alarm comparator, and output buffer - from one SOIC-14 device. The commercial temperature grade suits enclosed panel environments; verify enclosure temperature against the operating range in the manufacturer datasheet before deployment in hot cabinets. The ground-sensing inputs read low-side shunt voltages directly, and the output swings close to ground for ADC-friendly low-level signals. Budget headroom: signals within about 1.5 V of the 24 V rail cannot be faithfully amplified, so scale loops into the 0.3 V to 3 V mid-range region.
अनुशंसित
Consumer Audio Preamps and Mixers
In cost-sensitive consumer audio, the LM324ADG supplies microphone preamp, mixer summing, and line-buffer stages in one quad package, keeping BOM cost low for mixers, small PA heads, and set-top audio front ends. Biasing at mid-supply with a resistor divider enables single-supply AC-coupled operation, and the ground-reaching input range simplifies bias networks. The trade-off is performance class: 1 MHz GBW and 0.6 V/us slew rate mean full output swing is limited to roughly 10 kHz signals, and noise and distortion are higher than dedicated audio op amps, so use it where cost dominates and signal levels are moderate. For upgraded channels needing more bandwidth and lower distortion in the same footprint, the TS974IDT offers a pin-compatible improvement path without PCB changes.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा LM324ADG — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | MC3403DR | LM324ADR | TS974IDT | LM324ADT |
|---|---|---|---|---|---|
| Package | 14-SOIC (3.90 mm) | 14-SOIC (3.90 mm) - same | 14-SOIC (3.90 mm) - same | 14-SOIC (3.90 mm) - same | 14-SOIC (3.90 mm) - same |
| Brand | onsemi | onsemi | Texas Instruments | STMicroelectronics | onsemi |
| Number of Circuits | 4 | 4 | 4 | 4 | 4 |
| Packaging | Tube | Tape & Reel | Tape & Reel | Tape & Reel | Tape & Reel |
मुख्य विशेषताएँ
- 'A'-grade 3 mV maximum input offset voltage (बनामLM324M)
- Lower quiescent power than four discrete op amps (बनामMC3403DR)
- Ground-sensing input range at low cost (बनामTS974IDT)
डिज़ाइन नोट्स
The LM324ADG input common-mode range extends to the negative rail but stops about 1.5 V below the positive supply. Driving an input within roughly 1.5 V of V+ causes the output to step or invert unexpectedly - a classic LM324 failure mode. Bias single-supply circuits at mid-rail or keep input peaks below V+ minus 1.5 V. Similarly, budget output swing: at light loads the output reaches near ground but stops about 1.5 V short of V+. Reference the manufacturer datasheet typical-performance curves when computing usable swing at your specific load.
Capacitively decouple the V+ pin (pin 4) with a 100 nF ceramic placed within a few millimeters of the pin plus a 1 uF bulk capacitor per board region. Because four amplifiers share one supply pin, transient currents from simultaneous output transitions can couple between channels through shared supply impedance; a local decoupling network plus short, wide supply traces suppresses this cross-channel interference. In mixed-signal boards, keep op-amp supply returns separate from digital ground returns until a single deliberate star point.
Unused LM324 channels must be terminated, not left floating: configure each unused amplifier as a unity-gain follower with its output tied to its inverting input and the non-inverting input connected to mid-supply (or ground-referenced divider). Floating inputs pick up board noise, can slew to a rail, and inject crosstalk into adjacent active channels through the shared die and supply. This termination practice also prevents unintended oscillation of the internally compensated stages.
Keep feedback resistors in the 1 kOhm to 100 kOhm range: very large values amplify input bias-current error into output offset, while very small values load the bipolar output stage and increase distortion. For high-value feedback networks, add a small parallel capacitor (a few pF) across the feedback resistor to limit noise gain and ensure phase margin, per standard LM324 application practice. Route input traces short and guard them from output traces to avoid parasitic feedback at high closed-loop gains.
अनुपालन जानकारी
Compliance declarations were not stated in this page's source listings. Consult the official onsemi product page for LM324ADG for RoHS, REACH, and material-composition certificates.