Texas Instruments

LM358D-JF - Dual Op-Amp, 2 Circuit, SOIC-8 | Texas Instruments

MPN: LM358D-JF ✓ सक्रिय
3 V to 36 V Vdss 300 uA Id 8-SOIC (surface mount) Package
न्यूनतम ऑर्डर मात्रा: 1 |

LM358D-JF अवलोकन

The Texas Instruments LM358D-JF is an industry-standard dual operational amplifier integrating two independent, internally compensated op-amp circuits in a single 8-pin SOIC package. According to the TI LM358 family datasheet, the device operates from a single supply as low as 3 V (B and BA versions) with a wide supply range up to 36 V, draws approximately 300 uA per channel of quiescent current (B and BA versions), and delivers a unity-gain bandwidth of about 1.2 MHz on the enhanced B/BA versions, with the standard LM358 characterized at 700 kHz on a 30-V class supply. The common-mode input voltage range includes ground, enabling direct sensing of signals near 0 V without a negative rail.

An operational amplifier is an analog voltage amplifier with differential inputs and a single-ended output, forming the foundational building block of the linear signal chain: op-amp -> amplifier IC -> analog front end -> mixed-signal system. Dual op-amps such as the LM358D-JF combine two such stages behind one supply pin, halving board area and supply routing complexity compared with two single amplifiers.

Key features include ground-sensing inputs for single-supply operation, a wide supply range supporting both 5 V logic-level and up to 36 V industrial rails (B/BA versions), low 300 uA-per-channel quiescent drain (B/BA versions) for battery-powered designs, and internally compensated unity-gain stability. The maximum input offset voltage of 2 mV at 25 C (BA version) keeps DC accuracy adequate for non-critical gain stages.

The architecture uses a classic bipolar process with internal frequency compensation, giving well-behaved, phase-margin-safe behavior in inverting, non-inverting, and unity-gain buffer configurations. Output stages sink and source small currents and pull down close to ground on single supplies, which is why the LM358 remains the default comparator-adjacent amplifier for cost-driven designs.

Typical applications include transducer signal conditioning near ground, low-speed active filters, current-sense front ends in power supplies and chargers, and level-shifting stages in industrial sensor nodes. The SOIC-8 surface-mount footprint suits compact commercial PCBs.

Design consideration: keep closed-loop gains moderate and load capacitance low; the modest bandwidth means these parts are intended for slow, robust analog functions rather than wideband signal paths.

This page adds value beyond the manufacturer datasheet by consolidating pin-compatible alternatives, pricing-channel availability, and practical design notes in one place.

के लिए ड्रॉप-इन विकल्प LM358D-JF — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

इस सीरीज़ के वेरिएंट

समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं LM358D-JF (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Package, Input Offset Voltage, Amplifier Type, Slew Rate, Common-Mode Input Range.

Texas Instruments
Package: SOIC-8 (D)
Input Offset Voltage: 0.5 mV typical / 3 mV maximum
Slew Rate: 0.5 V/us (typical)
इसके साथ तुलना करें LM358D-JF →
Texas Instruments
Package: 8-SOIC (D)
Input Offset Voltage: 2 mV (typical)
Amplifier Type: General Purpose
इसके साथ तुलना करें LM358D-JF →
Texas Instruments
Package: 8-pin micro PBGA surface-mount package
Input Offset Voltage: 3 mV maximum
इसके साथ तुलना करें LM358D-JF →
Texas Instruments
Package: SOIC-8 (D)
Input Offset Voltage: 2 mV (typ), 7 mV (max)
Amplifier Type: General Purpose Operational Amplifier
इसके साथ तुलना करें LM358D-JF →

LM358D

✅ ड्रॉप-इन
Texas Instruments
📦 8-SOIC
General Purpose Operational Amplifier · 2 · 700 kHz · 0.3 V/µs · 3 V to 32 V · ±1.5 V to ±16 V · 0.7 mA (typ) · 2 mV (typ), 7 mV (max)

कीमत के लिए संपर्क करें

डेटाशीट देखें →

LM358BP

✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित
Texas Instruments
📦 8-SOIC
Dual operational amplifier · 2 channels · Up to 36 V · 1.2 MHz · 3 mV maximum · -40°C to +85°C · 8-pin micro PBGA surface-mount package · Surface mount

कीमत के लिए संपर्क करें

डेटाशीट देखें →

LM2904BIDR

✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित
Texas Instruments
📦 8-SOIC
Texas Instruments · Industry-standard dual operational amplifier · 2 (Dual) · 3 V to 36 V · +/-1.5 V to +/-18 V · 1.2 MHz · 0.5 V/us (typical) · 0.5 mV typical / 3 mV maximum

कीमत के लिए संपर्क करें

डेटाशीट देखें →

LM2904DR

✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित
Texas Instruments
📦 8-SOIC
2 · 3 V to 26 V · ±1.5 V to ±13 V · 700 kHz · 0.3 V/us · 2 mV (typical) · 500 uA (typical) · 0.7 mA (typical)

कीमत के लिए संपर्क करें

डेटाशीट देखें →

LM358D-JF Maximum Ratings और Electrical Characteristics

Amplifier Configuration Dual (2 independent circuits)
Amplifier Type Standard general-purpose operational amplifier
Supply Voltage Range (B/BA versions) 3 V to 36 V
Supply Voltage (family characterization) 30 V class (per TI LM358 product page)
Unity-Gain Bandwidth (B/BA versions) 1.2 MHz
Unity-Gain Bandwidth (standard LM358) 700 kHz
Quiescent Current per Channel (B/BA versions) 300 uA
Input Offset Voltage Max at 25C (BA version) 2 mV
Input Common-Mode Range Includes ground (0 V)
पैकेज 8-SOIC (surface mount)
माउंटिंग प्रकार Surface Mount

LM358D-JF पिन कॉन्फ़िगरेशन

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
पिन 1 OUT1 — Output of amplifier A
पिन 2 IN1- — Inverting input of amplifier A
पिन 3 IN1+ — Non-inverting input of amplifier A
पिन 4 GND/V- — Ground or negative supply
पिन 5 IN2+ — Non-inverting input of amplifier B
पिन 6 IN2- — Inverting input of amplifier B
पिन 7 OUT2 — Output of amplifier B
पिन 8 VCC/V+ — Positive supply

सामान्य अनुप्रयोग

LM358D-JF के लिए उपयुक्त है 6 अनुप्रयोगs: Low-Side Current Sensing, Transducer Signal Conditioning, Active Filters and Level Shifting, Power Supply Supervision and Control Loops, Battery-Powered Portable Instruments, Industrial Sensor Nodes and PLC I/O.

⚡

Low-Side Current Sensing

The LM358D-JF's common-mode input range that includes ground makes it a natural amplifier for low-side current-sense shunts in single-supply systems, where the shunt voltage sits only millivolts above 0 V. The ground-sensing inputs allow direct measurement without negative rails or input-level shifting, keeping the front end to one SOIC-8 device plus two resistors. Its 700 kHz to 1.2 MHz class bandwidth is ample for charger, power-supply, and motor-current monitoring loops that respond in the kilohertz range, and the 2 mV maximum offset (BA version) bounds the DC error budget on small shunt signals. For faster or more precise current monitoring, TI's dedicated current-sense amplifiers are the upgrade path.

🧩

Transducer Signal Conditioning

Pressure, light, and temperature transducers commonly produce small differential or ground-referenced single-ended outputs that need modest, stable gain before digitization. The LM358D-JF provides two independent amplifiers for separate conditioning channels - for example, one gain stage for the sensor and a second for offset or reference generation - in one 8-SOIC package. The internally compensated design guarantees unity-gain stability, so configurations from unity buffer to moderate closed-loop gains behave predictably without external compensation. Its single-supply operation from 3 V upward matches modern microcontroller ADC rails, and the 300 uA-per-channel quiescent current (B/BA versions) keeps battery-powered logger designs within tight power budgets.

🔧

Active Filters and Level Shifting

Low-frequency active filters, anti-aliasing stages, and DC level-shift circuits are classic LM358 duties. The 700 kHz standard bandwidth (1.2 MHz on B/BA versions) comfortably supports Sallen-Key and multiple-feedback filters with cutoffs in the tens of kilohertz, while the ground-inclusive common-mode range lets filter nodes operate from a single positive rail. The dual channels of the LM358D-JF let one package implement a second-order filter (two stages) or one filter stage plus one output buffer, halving board area versus two single amplifiers. Designers should keep closed-loop gains moderate and avoid large capacitive loads to preserve phase margin, per the TI LM358 datasheet stability guidance.

🔌

Power Supply Supervision and Control Loops

In AC-DC converters, chargers, and DC-DC modules, the LM358D-JF amplifies shunt and divider signals for feedback and fault detection. The 36 V maximum supply rating on B/BA versions tolerates high-voltage auxiliary rails, and outputs pull close to ground on single supplies - convenient when interfacing directly to PWM controller error inputs referenced near 0 V. The dual package typically serves one amplifier as an error amplifier and the second as an overcurrent comparator-adjacent stage. Because loop bandwidths in power conversion are usually well below 100 kHz, the 700 kHz to 1.2 MHz bandwidth is not a limitation, and the low quiescent current supports standby-power requirements in consumer adapters.

📱

Battery-Powered Portable Instruments

Multimeters, sensor loggers, and portable test tools benefit from the LM358D-JF's low quiescent drain of about 300 uA per channel (B/BA versions) and single-supply operation from 3 V, which runs directly from two alkaline cells or one lithium cell with a small boost regulator. The ground-sensing inputs read battery-voltage dividers and sensor outputs without rail-referencing circuitry. The SOIC-8 footprint suits compact handheld PCBs, and the industry-standard pinout allows sourcing flexibility across TI and second sources such as STMicroelectronics. For designs where every microamp counts at shutdown, verify datasheet supply-current versus supply-voltage curves and consider TI's low-Iq op-amp families as drop-path upgrades.

🏭

Industrial Sensor Nodes and PLC I/O

Factory sensor nodes conditioning 4-20 mA loop signals, thermistor dividers, and proximity-switch inputs use the LM358D-JF for its robustness, wide 3 V to 36 V supply range (B/BA versions), and tolerance of ground-referenced signals in noisy industrial environments. One SOIC-8 package handles two channels - for example, signal amplification and fault threshold comparison - reducing component count on dense I/O cards. The LM2904 grade within the same TI family offers automotive/industrial temperature qualification on an identical footprint, giving designers a qualified-part migration path without PCB changes. Typical loop circuits remain far below the device bandwidth, so linearity and offset stability dominate the design choices.

What is the LM358D-JF?
The LM358D-JF is a Texas Instruments industry-standard dual operational amplifier with two independent, internally compensated op-amp circuits in an 8-pin SOIC surface-mount package. According to the TI LM358 family datasheet, the device supports a supply range of 3 V to 36 V on the B/BA versions, draws about 300 uA per channel, and its common-mode input range includes ground, allowing direct sensing of signals near 0 V in single-supply systems.
What is the supply voltage range of the LM358D-JF?
The LM358 family operates from a single supply; the B and BA versions support a wide supply range of 3 V to 36 V. TI characterizes the standard LM358 as a 30-V, 700-kHz operational amplifier on its product page. The same device can also run from split supplies in dual-rail systems. Always confirm the exact rating for your specific grade in the TI LM358 datasheet before finalizing the design.
What is the bandwidth of the LM358D-JF?
The enhanced B and BA versions of the LM358 deliver a unity-gain bandwidth of 1.2 MHz, while TI characterizes the standard LM358 at 700 kHz. This modest bandwidth makes the device suitable for low-frequency transducer conditioning, active filters, and control loops, but unsuitable for wideband video or RF signal chains. Consult the TI LM358 datasheet gain-versus-frequency curves when sizing closed-loop gain above unity.
What is the difference between LM358D and LM358D-JF?
The LM358D-JF is a Texas Instruments ordering variant of the LM358D dual op-amp: the D suffix denotes the same 8-SOIC package, and the -JF suffix denotes a specific TI packing/shipping code. Electrically the two share the same die and pinout, so one drops directly into the other's footprint. Confirm the exact reel-quantity difference between the two suffixes in the TI ordering table of the LM358 datasheet.
What is the quiescent current of the LM358D-JF?
According to the TI LM358 family datasheet, the B and BA versions draw a quiescent current of approximately 300 uA per channel, which is roughly 600 uA total for both amplifiers in the dual package. This low drain makes the part well suited to battery-powered sensor nodes and portable instruments. For your exact grade, check the supply current rows in the TI datasheet electrical characteristics table.
What is the input offset voltage of the LM358D-JF?
The BA version of the LM358 family specifies a maximum input offset voltage of 2 mV at 25 C per the TI datasheet. This level of DC accuracy is adequate for general-purpose gain stages, level shifting, and comparator-adjacent duties, but precision applications such as thermocouple front ends or shunt current measurement may need a trimmed or zero-drift amplifier instead. Refer to the electrical characteristics table in the TI LM358 datasheet for typical and over-temperature values.
What is the pinout of the LM358D-JF in SOIC-8?
The LM358D-JF uses the industry-standard LM358 SOIC-8 pinout: pin 1 is output A, pin 2 is inverting input A, pin 3 is non-inverting input A, pin 4 is ground/V-, pin 5 is non-inverting input B, pin 6 is inverting input B, pin 7 is output B, and pin 8 is VCC/V+. Use the pin-description table in the TI LM358 datasheet when assigning PCB tracks.
Can LM358D replace LM358D-JF as a drop-in alternative?
Yes. STMicroelectronics offers the LM358D in the same 8-SOIC package with the same industry-standard LM358 pinout and comparable general-purpose specifications, making it a practical drop-in replacement for the TI LM358D-JF on the same PCB footprint. Because the LM358 has been second-sourced for decades, always compare the specific electrical characteristics tables of both manufacturers' datasheets for parameters critical to your application before qualifying the substitution.
What are the best TI drop-in alternatives to the LM358D-JF?
Within Texas Instruments, the closest same-family drop-in options in 8-SOIC are the enhanced LM358B and the automotive-oriented LM2904B, both pin-to-pin compatible with the LM358D-JF. The B versions add the wider 3 V to 36 V supply range, 1.2 MHz bandwidth, and 300 uA-per-channel quiescent current, so they work directly on an existing LM358 footprint with improved performance. Check the LM358B and LM2904B datasheets for grade-specific temperature ranges.
When should I choose the LM358D-JF over the LM358B?
Choose the LM358D-JF when your design needs the lowest-cost, industry-standard LM358 behavior in 8-SOIC and your specifications are met by the standard-grade bandwidth and offset figures. Choose the TI LM358B when you need the wider 3 V to 36 V supply range, 1.2 MHz bandwidth, or 300 uA-per-channel quiescent current on the same footprint. Both are pin-compatible, so switching later requires only a BOM change, not a PCB redesign - a common migration path in cost-sensitive industrial designs.
Is the LM358D-JF suitable for single-supply operation near ground?
Yes. A defining feature of the LM358 family is that the common-mode input voltage range includes ground, so the LM358D-JF senses signals down to 0 V without a negative rail, according to the TI datasheet. This makes it ideal for single-supply current sensing on low-side shunts, ground-referenced transducer conditioning, and battery-powered designs. Note that output swing and input headroom limits still apply; consult the TI datasheet output characteristics for exact near-rail behavior.
Where can I download the LM358D-JF datasheet PDF?
The LM358D-JF datasheet PDF is available through Texas Instruments' official product page at ti.com/product/LM358 and through datasheet aggregators such as alldatasheet.com, which hosts the 64-page TI LM358 family document. Request a quote on this page and our team can also provide the current official datasheet link with your order confirmation. Always use the manufacturer's latest revision for design work.
What is the lead time and how can I buy the LM358D-JF?
Submit the Request a Quote form on this page to receive current stock, price, and lead time for the TI LM358D-JF from XAIPART. The part is listed by distributors such as DigiKey as an in-stock, ship-today item, which indicates healthy supply-chain availability. Packaging quantity and reel size for the -JF suffix should be confirmed against the TI ordering information table in the LM358 datasheet when planning production volumes.
What is the best cross-brand equivalent for the LM358D-JF?
The best cross-brand equivalent is the STMicroelectronics LM358D, which shares the same 8-SOIC package, the identical industry-standard LM358 pinout, and the same dual general-purpose op-amp function. Other long-standing second sources of the LM358 include KEC, Philips/NXP, and Toshiba per cross-reference listings. Because the LM358 is one of the most widely second-sourced analog ICs, footprint compatibility is reliable, but parameter tables vary slightly by vendor - always qualify against the specific datasheet.
What are the key specifications of the LM358D-JF that engineers should know?
The LM358D-JF is a TI dual op-amp in 8-SOIC with two independent internally compensated amplifiers, a single-supply range from 3 V up to 36 V on B/BA versions (30-V class standard grade), 1.2 MHz unity-gain bandwidth on B/BA versions (700 kHz standard), about 300 uA per channel quiescent current, a 2 mV maximum input offset at 25 C on the BA version, and a common-mode input range that includes ground. These figures come from the TI LM358 family datasheet and product page.

के लिए इंजीनियरिंग संदर्भ डेटा LM358D-JF — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose the LM358D-JF when you need the lowest-cost, industry-standard dual op-amp for slow, robust analog functions - transducer conditioning, low-side current sensing, active filters up to tens of kilohertz, or power-supply supervision - on a single supply from 3 V upward. Choose the TI LM358B on the same footprint when the wider 3 V to 36 V range, 1.2 MHz bandwidth, or 300 uA-per-channel drain matters. Choose the TI LM2904 or LM2904B grades for automotive or wide-temperature industrial builds requiring qualified parts. Choose the STMicroelectronics LM358D for a cross-brand second source or when procurement favors multi-sourcing. Trade-offs to accept: no rail-to-rail output swing, no shutdown pin, and modest slew rate - for those needs, move to TI's rail-to-rail or low-Iq amplifier families instead.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद LM358D (ST) LM358B (LM358BIDR) LM2904B (LM2904BIDR) LM2904 (LM2904DR)
Package 8-SOIC 8-SOIC - same 8-SOIC - same 8-SOIC - same 8-SOIC - same
Brand Texas Instruments STMicroelectronics Texas Instruments Texas Instruments Texas Instruments
Amplifier Channels 2 2 2 2 2
Input Common-Mode Range Includes Ground Yes Yes Yes Yes Yes

मुख्य विशेषताएँ

  • Ground-sensing inputs on a 30-V class supply (बनामLM358B (LM358BIDR))
  • Dual-channel integration (बनामLM324-family quad parts (e.g. MC3403DR))
  • Multi-source availability (बनामLM358D (STMicroelectronics))

डिज़ाइन नोट्स

Remember that the LM358 output stage cannot pull all the way to the positive rail and has limited sink capability near ground on single supplies. Designs that assume rail-to-rail output swing - such as ADC driver references set close to VCC - will clip. Keep the output swing several hundred millivolts inside the rails, or select a rail-to-rail CMOS amplifier if the signal chain requires full-range swing. Check the TI LM358 datasheet output-voltage-swing curves for the exact limits at your load current and supply voltage.

Budget total quiescent current as roughly two channels times the per-channel figure (about 600 uA total on B/BA versions at 300 uA/channel) plus load currents. In battery-powered designs, place the amplifier in a switched rail or use the enable-like power gating of a downstream regulator rather than assuming near-zero standby drain; the LM358 family predates shutdown pins. Verify the supply current versus supply voltage and temperature curves in the TI datasheet for the exact grade used.

Place a 100 nF ceramic decoupling capacitor directly across pins 4 and 8, within a few millimeters of the SOIC-8 body, and add bulk capacitance per board standard. Keep input traces short and guard the high-impedance inverting node to limit leakage-driven offset errors. The SOIC-8 footprint is the industry-standard LM358 land pattern, so layout reuse from existing LM358 designs is safe; verify pin 1 marking orientation against the TI datasheet package diagram before reflow.

अनुपालन जानकारी

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

Compliance status for the -JF suffix should be confirmed on the TI product page for LM358; the LM2904/LM2904B grades carry automotive qualification within the same family.

डेटा सत्यापन तिथि: 2026-11-08 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

lm358d datasheet lm358d pinout lm358d smd lm358d datasheet pdf lm358d footprint lm358d pdf LM358D-JF datasheet LM358D-JF pinout SOIC-8 LM358D-JF equivalent LM358D-JF replacement LM358D-JF vs LM358D Texas Instruments LM358D-JF LM358D-JF buy price

संबंधित कंपोनेंट्स और शब्द

Texas Instruments LM358D-JF LM358D LM358B LM2904B LM358 LM2904 STMicroelectronics dual operational amplifier op-amp operational amplifier amplifier IC SOIC-8 surface mount unity-gain bandwidth input offset voltage quiescent current common-mode input range single-supply operation RoHS low-side current sensing active filter signal conditioning
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें