LM358D-JF - Dual Op-Amp, 2 Circuit, SOIC-8 | Texas Instruments
MPN: LM358D-JF ✓ AktifLM358D-JF Genel Bakış
An operational amplifier is an analog voltage amplifier with differential inputs and a single-ended output, forming the foundational building block of the linear signal chain: op-amp -> amplifier IC -> analog front end -> mixed-signal system. Dual op-amps such as the LM358D-JF combine two such stages behind one supply pin, halving board area and supply routing complexity compared with two single amplifiers.
Key features include ground-sensing inputs for single-supply operation, a wide supply range supporting both 5 V logic-level and up to 36 V industrial rails (B/BA versions), low 300 uA-per-channel quiescent drain (B/BA versions) for battery-powered designs, and internally compensated unity-gain stability. The maximum input offset voltage of 2 mV at 25 C (BA version) keeps DC accuracy adequate for non-critical gain stages.
The architecture uses a classic bipolar process with internal frequency compensation, giving well-behaved, phase-margin-safe behavior in inverting, non-inverting, and unity-gain buffer configurations. Output stages sink and source small currents and pull down close to ground on single supplies, which is why the LM358 remains the default comparator-adjacent amplifier for cost-driven designs.
Typical applications include transducer signal conditioning near ground, low-speed active filters, current-sense front ends in power supplies and chargers, and level-shifting stages in industrial sensor nodes. The SOIC-8 surface-mount footprint suits compact commercial PCBs.
Design consideration: keep closed-loop gains moderate and load capacitance low; the modest bandwidth means these parts are intended for slow, robust analog functions rather than wideband signal paths.
This page adds value beyond the manufacturer datasheet by consolidating pin-compatible alternatives, pricing-channel availability, and practical design notes in one place.
Drop-in alternatifler için LM358D-JF — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller LM358D-JF (aynı form faktörü ve ayağa oturma) — farklı olan Package, Input Offset Voltage, Amplifier Type, Slew Rate, Common-Mode Input Range.
LM358D
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →LM358BP
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →LM2904BIDR
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →LM2904DR
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →LM358D-JF Maksimum Değerlendirmeler & Elektriksel Özellikler
| Amplifier Configuration | Dual (2 independent circuits) |
| Amplifier Type | Standard general-purpose operational amplifier |
| Supply Voltage Range (B/BA versions) | 3 V to 36 V |
| Supply Voltage (family characterization) | 30 V class (per TI LM358 product page) |
| Unity-Gain Bandwidth (B/BA versions) | 1.2 MHz |
| Unity-Gain Bandwidth (standard LM358) | 700 kHz |
| Quiescent Current per Channel (B/BA versions) | 300 uA |
| Input Offset Voltage Max at 25C (BA version) | 2 mV |
| Input Common-Mode Range | Includes ground (0 V) |
| Paket | 8-SOIC (surface mount) |
| Montaj Türü | Surface Mount |
LM358D-JF Pin Yapısı
| Pin 1 | OUT1 — Output of amplifier A |
| Pin 2 | IN1- — Inverting input of amplifier A |
| Pin 3 | IN1+ — Non-inverting input of amplifier A |
| Pin 4 | GND/V- — Ground or negative supply |
| Pin 5 | IN2+ — Non-inverting input of amplifier B |
| Pin 6 | IN2- — Inverting input of amplifier B |
| Pin 7 | OUT2 — Output of amplifier B |
| Pin 8 | VCC/V+ — Positive supply |
Tipik Uygulamalar
LM358D-JF için uygundur 6 uygulamas: Low-Side Current Sensing, Transducer Signal Conditioning, Active Filters and Level Shifting, Power Supply Supervision and Control Loops, Battery-Powered Portable Instruments, Industrial Sensor Nodes and PLC I/O.
Low-Side Current Sensing
The LM358D-JF's common-mode input range that includes ground makes it a natural amplifier for low-side current-sense shunts in single-supply systems, where the shunt voltage sits only millivolts above 0 V. The ground-sensing inputs allow direct measurement without negative rails or input-level shifting, keeping the front end to one SOIC-8 device plus two resistors. Its 700 kHz to 1.2 MHz class bandwidth is ample for charger, power-supply, and motor-current monitoring loops that respond in the kilohertz range, and the 2 mV maximum offset (BA version) bounds the DC error budget on small shunt signals. For faster or more precise current monitoring, TI's dedicated current-sense amplifiers are the upgrade path.
Önerilen
Transducer Signal Conditioning
Pressure, light, and temperature transducers commonly produce small differential or ground-referenced single-ended outputs that need modest, stable gain before digitization. The LM358D-JF provides two independent amplifiers for separate conditioning channels - for example, one gain stage for the sensor and a second for offset or reference generation - in one 8-SOIC package. The internally compensated design guarantees unity-gain stability, so configurations from unity buffer to moderate closed-loop gains behave predictably without external compensation. Its single-supply operation from 3 V upward matches modern microcontroller ADC rails, and the 300 uA-per-channel quiescent current (B/BA versions) keeps battery-powered logger designs within tight power budgets.
Önerilen
Active Filters and Level Shifting
Low-frequency active filters, anti-aliasing stages, and DC level-shift circuits are classic LM358 duties. The 700 kHz standard bandwidth (1.2 MHz on B/BA versions) comfortably supports Sallen-Key and multiple-feedback filters with cutoffs in the tens of kilohertz, while the ground-inclusive common-mode range lets filter nodes operate from a single positive rail. The dual channels of the LM358D-JF let one package implement a second-order filter (two stages) or one filter stage plus one output buffer, halving board area versus two single amplifiers. Designers should keep closed-loop gains moderate and avoid large capacitive loads to preserve phase margin, per the TI LM358 datasheet stability guidance.
Önerilen
Power Supply Supervision and Control Loops
In AC-DC converters, chargers, and DC-DC modules, the LM358D-JF amplifies shunt and divider signals for feedback and fault detection. The 36 V maximum supply rating on B/BA versions tolerates high-voltage auxiliary rails, and outputs pull close to ground on single supplies - convenient when interfacing directly to PWM controller error inputs referenced near 0 V. The dual package typically serves one amplifier as an error amplifier and the second as an overcurrent comparator-adjacent stage. Because loop bandwidths in power conversion are usually well below 100 kHz, the 700 kHz to 1.2 MHz bandwidth is not a limitation, and the low quiescent current supports standby-power requirements in consumer adapters.
Önerilen
Battery-Powered Portable Instruments
Multimeters, sensor loggers, and portable test tools benefit from the LM358D-JF's low quiescent drain of about 300 uA per channel (B/BA versions) and single-supply operation from 3 V, which runs directly from two alkaline cells or one lithium cell with a small boost regulator. The ground-sensing inputs read battery-voltage dividers and sensor outputs without rail-referencing circuitry. The SOIC-8 footprint suits compact handheld PCBs, and the industry-standard pinout allows sourcing flexibility across TI and second sources such as STMicroelectronics. For designs where every microamp counts at shutdown, verify datasheet supply-current versus supply-voltage curves and consider TI's low-Iq op-amp families as drop-path upgrades.
Önerilen
Industrial Sensor Nodes and PLC I/O
Factory sensor nodes conditioning 4-20 mA loop signals, thermistor dividers, and proximity-switch inputs use the LM358D-JF for its robustness, wide 3 V to 36 V supply range (B/BA versions), and tolerance of ground-referenced signals in noisy industrial environments. One SOIC-8 package handles two channels - for example, signal amplification and fault threshold comparison - reducing component count on dense I/O cards. The LM2904 grade within the same TI family offers automotive/industrial temperature qualification on an identical footprint, giving designers a qualified-part migration path without PCB changes. Typical loop circuits remain far below the device bandwidth, so linearity and offset stability dominate the design choices.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: LM358D-JF — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | LM358D (ST) | LM358B (LM358BIDR) | LM2904B (LM2904BIDR) | LM2904 (LM2904DR) |
|---|---|---|---|---|---|
| Package | 8-SOIC | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same |
| Brand | Texas Instruments | STMicroelectronics | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Channels | 2 | 2 | 2 | 2 | 2 |
| Input Common-Mode Range Includes Ground | Yes | Yes | Yes | Yes | Yes |
Ana Farklılayıcılar
- Ground-sensing inputs on a 30-V class supply (karşılaştırma:LM358B (LM358BIDR))
- Dual-channel integration (karşılaştırma:LM324-family quad parts (e.g. MC3403DR))
- Multi-source availability (karşılaştırma:LM358D (STMicroelectronics))
Tasarım Notları
Remember that the LM358 output stage cannot pull all the way to the positive rail and has limited sink capability near ground on single supplies. Designs that assume rail-to-rail output swing - such as ADC driver references set close to VCC - will clip. Keep the output swing several hundred millivolts inside the rails, or select a rail-to-rail CMOS amplifier if the signal chain requires full-range swing. Check the TI LM358 datasheet output-voltage-swing curves for the exact limits at your load current and supply voltage.
Budget total quiescent current as roughly two channels times the per-channel figure (about 600 uA total on B/BA versions at 300 uA/channel) plus load currents. In battery-powered designs, place the amplifier in a switched rail or use the enable-like power gating of a downstream regulator rather than assuming near-zero standby drain; the LM358 family predates shutdown pins. Verify the supply current versus supply voltage and temperature curves in the TI datasheet for the exact grade used.
Place a 100 nF ceramic decoupling capacitor directly across pins 4 and 8, within a few millimeters of the SOIC-8 body, and add bulk capacitance per board standard. Keep input traces short and guard the high-impedance inverting node to limit leakage-driven offset errors. The SOIC-8 footprint is the industry-standard LM358 land pattern, so layout reuse from existing LM358 designs is safe; verify pin 1 marking orientation against the TI datasheet package diagram before reflow.
Uyumluluk Bilgisi
Compliance status for the -JF suffix should be confirmed on the TI product page for LM358; the LM2904/LM2904B grades carry automotive qualification within the same family.