LPC43S67JET100E - Dual-Core 204MHz MCU 1MB Flash | NXP
MPN: LPC43S67JET100E ✓ सक्रियLPC43S67JET100E अवलोकन
A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripheral interfaces on one integrated circuit. In the hierarchy of electronic components, the LPC43S67JET100E is a 32-bit embedded microcontroller, part of the Arm Cortex-M class of microcontrollers, and ultimately belongs to the broader semiconductor and embedded-computing category. Its dual-core architecture allows the Cortex-M4 core to execute application or network-control code while the Cortex-M0 subsystem handles peripheral management or real-time tasks, reducing the need for a separate microcontroller on complex boards.
Key capabilities include a 204 MHz Arm Cortex-M4/M0 processor configuration, 1 MB of flash, and 154 kB of SRAM. The Cortex-M0 subsystem supports the LPC43S6x architecture's division of work between the primary processor and dedicated peripheral handling. Ethernet and two high-speed USB interfaces make the device suitable for connected industrial, communications, and control equipment, while the quad SPI Flash Interface supports external serial-memory expansion. An AES engine provides hardware assistance for cryptographic operations, and the 16 kB EEPROM provides nonvolatile storage for configuration or calibration data.
The LPC43S6x integrates advanced configurable peripherals such as SCTimer/PWM and Serial General Purpose I/O, allowing designers to tailor timer channels, signal routing, and I/O behavior for application-specific timing and control requirements. This integration is especially useful in systems that need deterministic peripheral handling while the main Cortex-M4 core handles protocols, control logic, or higher-level software. The Ethernet interface also makes the MCU suitable for gateways and network-connected embedded equipment without requiring a separate communications processor.
Typical uses include industrial Ethernet controllers, USB-connected data acquisition equipment, building automation controllers, embedded gateways, motor and motion-control platforms, and connected test systems. The 100-TFBGA package supports compact designs but requires careful PCB layout with multiple power and ground connections. Designers should use the manufacturer's pin-description table, power-supply recommendations, and decoupling requirements when assigning the 100-ball land pattern and planning high-speed USB or Ethernet signal routing.
The main design trade-off is package density: the 9 x 9 mm TFBGA minimizes PCB area but complicates assembly, inspection, and prototype rework compared with a leaded package. Stable rails, short return paths, controlled impedance routing, and careful exposed-ball layout are therefore more important than in a large-outline controller. This page also organizes the device's pricing route, replacement options, comparison parameters, and practical integration guidance for faster engineering evaluation.
के लिए ड्रॉप-इन विकल्प LPC43S67JET100E — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस सीरीज़ के वेरिएंट
समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं LPC43S67JET100E (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न On-Chip SRAM.
LPC43S67JET100
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
LPC4337JET100E
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →LPC4357JET100
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित📋 संदर्भ विकल्प (कैटलॉग में नहीं)
LPC4370FET100E
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →LPC43S67JET100B
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित📋 संदर्भ विकल्प (कैटलॉग में नहीं)
LPC43S67JET100E Maximum Ratings और Electrical Characteristics
| Product Type | 32-bit dual-core microcontroller |
| Main Processor Core | Arm Cortex-M4/M0 |
| Maximum Processor Frequency | 204 MHz |
| Flash Memory | 1 MB (1M x 8) |
| On-Chip SRAM | Up to 154 kB |
| On-Chip EEPROM | 16 kB |
| Ethernet Interface | 1 Ethernet interface |
| High-Speed USB Interface | 2 high-speed USB interfaces |
| External Serial Flash Interface | Quad SPI Flash Interface |
| Crypto Accelerator | AES engine |
| Advanced Timer Peripheral | SCTimer/PWM |
| Configurable I/O Peripheral | Serial General Purpose I/O |
| पैकेज | 100-TFBGA (9 x 9 mm) |
| माउंटिंग प्रकार | Surface mount |
| Packaging | Tray |
| RoHS स्थिति | RoHS code reported as Yes |
LPC43S67JET100E 100-tfbga (9 x 9 mm) पिन कॉन्फ़िगरेशन गाइड
LPC43S67JET100E (100-tfbga (9 x 9 mm) पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस डिजिटल IC में GPIO, संचार इंटरफ़ेस (UART, SPI, I2C) और पावर पिन शामिल हैं। वैकल्पिक पिन फ़ंक्शन और कॉन्फ़िगरेशन विकल्पों के लिए निर्माता डेटाशीट देखें। एम्बेडेड सिस्टम डिज़ाइन और PCB लेआउट के लिए आवश्यक।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: LPC43S67JET100E.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
LPC43S67JET100E के लिए उपयुक्त है 6 अनुप्रयोगs: Industrial Ethernet Gateways, USB Data Acquisition Equipment, Building Automation Controllers, Motor and Motion Control, Connected Embedded Test Systems, Secure Network Appliances.
Industrial Ethernet Gateways
The LPC43S67JET100E fits industrial Ethernet gateways because it combines a 204 MHz Arm Cortex-M4/M0 architecture with integrated Ethernet, 1 MB of flash, and up to 154 kB of SRAM. The Cortex-M4 core can execute protocol stacks and gateway logic while the Cortex-M0 subsystem manages timers, GPIO, and other peripherals. This dual-core arrangement allows deterministic I/O handling without forcing every interrupt-driven task onto the main processor. A key design consideration is to partition firmware and interrupt ownership carefully, then validate timing under sustained Ethernet traffic and industrial EMC conditions.
अनुशंसित
USB Data Acquisition Equipment
The LPC43S67JET100E is well suited to USB-connected data-acquisition equipment because it provides two high-speed USB interfaces alongside a 204 MHz Cortex-M4/M0 processor and substantial on-chip memory. One USB interface can support host or peripheral duties while the other serves a separate function, subject to the device's detailed mode configuration. The Cortex-M0 subsystem is useful for maintaining predictable sampling, trigger, and communication timing. Board design must preserve high-speed signal integrity through controlled-impedance routing, short return paths, and compliant connector and protection schemes.
अनुशंसित
Building Automation Controllers
The LPC43S67JET100E supports compact building-automation controllers that coordinate sensors, actuators, communications, and local control logic. Its 1 MB flash can hold application firmware and configuration data, while 154 kB of SRAM provides room for communication buffers and real-time state. Ethernet connectivity supports centralized monitoring, and the Cortex-M0 subsystem can service timing-sensitive peripheral operations while the Cortex-M4 core handles application logic. Designers should define deterministic update intervals and isolate network traffic from safety-critical timing paths during firmware validation.
अनुशंसित
Motor and Motion Control
The LPC43S67JET100E can be used in motor and motion-control subsystems where a high-performance control core and dedicated real-time subsystem are both valuable. Its 204 MHz Cortex-M4 core can execute motion algorithms, while the Cortex-M0 subsystem can manage timers, capture functions, and serial GPIO with predictable latency. The SCTimer/PWM resources support precise edge generation and period control. A practical implementation should separate control-loop timing from Ethernet or USB service tasks, verify PWM behavior at the worst-case operating condition, and include suitable gate drivers outside the MCU.
अनुशंसित
Connected Embedded Test Systems
The LPC43S67JET100E supports connected test and measurement systems that need substantial flash, real-time control, USB connectivity, and Ethernet communications in one compact package. The 1 MB flash stores firmware, test sequences, and calibration tables, while 154 kB of SRAM accommodates acquisition buffers and protocol state. Its dual-core organization allows one core to manage test sequencing and the other to service peripherals or communication timing. For sensitive analog measurement systems, separate the analog front end from the digital supply paths and use controlled grounding to prevent controller activity from disturbing acquired signals.
अनुशंसित
Secure Network Appliances
The LPC43S67JET100E is appropriate for compact network appliances that require Ethernet, USB service connectivity, and hardware-assisted cryptography. Its AES engine assists with cryptographic processing, while the 204 MHz Cortex-M4/M0 platform can divide network workloads from peripheral and security-monitor tasks. The 100-TFBGA package allows a dense implementation, but careful plane partitioning, impedance control, and power filtering are necessary to protect high-speed and security-sensitive paths. Firmware design should establish secure boot, key-management boundaries, fault recovery, and update procedures before production deployment.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा LPC43S67JET100E — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | LPC43S67JET100 | LPC4337JET100 | LPC4357JET100 | LPC4370FET100E |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 100-TFBGA (9 x 9 mm) | 100-TFBGA (9 x 9 mm) | 100-TFBGA (9 x 9 mm) | 100-TFBGA (9 x 9 mm) | 100-TFBGA (9 x 9 mm) |
मुख्य विशेषताएँ
- Dedicated Cortex-M0 subsystem supports concurrent peripheral management (बनामLPC4370FET100E)
- Two high-speed USB interfaces expand peripheral connectivity (बनामLPC4337JET100)
- Up to 154 kB SRAM supports richer communication and control buffers (बनामLPC43S67JET100)
- Integrated connectivity reduces external controller demand (बनामLPC4357JET100)
डिज़ाइन नोट्स
Implement the 100-TFBGA power network by following NXP's recommended ball grouping, via arrangement, and capacitor placement. Place each decoupling capacitor directly between its associated device supply ball and the nearest ground reference, with very short loops. Avoid routing Ethernet, USB, or other high-speed nets across split planes, and confirm every package ball against the LPC43S67JET100 pin table before releasing artwork. Because the package is only 9 x 9 mm, assembly capability and X-ray inspection should be planned early rather than treated as production afterthoughts.
Treat Ethernet and high-speed USB routes as controlled-impedance transmission lines using the PCB fabricator's stack-up. Maintain continuous reference planes, minimize stub branches, and place termination or protection components where their effect on the edge rate is controlled. Isolate noisy switching nodes and regulator return currents from analog or measurement circuits. The controller's 204 MHz processing capability does not imply that every PCB trace should be treated as a high-speed clock route; instead, follow the interface-specific rise-time and impedance requirements in the manufacturer documentation.
Do not treat the LPC43S67JET100, LPC43S67JET100E, and other LPC43-family ordering codes as unconditional substitutions. Verify the temperature grade, qualification state, exposed-ball requirements, memory configuration, boot configuration, peripheral mapping, and package drawing. Likewise, verify the Cortex-M0 subsystem assignment and interrupt routing before reusing firmware between LPC43S6x devices. The closest alternative is the one that passes both the mechanical footprint comparison and the application-specific peripheral and qualification review.
Partition the MCU's digital supply paths carefully and follow the manufacturer's recommended voltage rails and capacitor values. Do not infer the complete power architecture from the headline 204 MHz specification because processor activity, enabled peripherals, USB, and Ethernet traffic affect instantaneous demand. Use the datasheet's absolute maximum ratings, recommended operating conditions, power-consumption tables, and layout example as the design basis. Validate startup, brownout behavior, and rail sequencing across temperature and the intended Ethernet and USB traffic conditions.
अनुपालन जानकारी
The product-comparison source reports a RoHS code of Yes for the LPC43S6x family. No separate REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration is stated for the exact LPC43S67JET100E ordering code.