LPC43S67JET100E - Dual-Core 204MHz MCU 1MB Flash | NXP
MPN: LPC43S67JET100E ✓ 啟用中LPC43S67JET100E 概覽
A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripheral interfaces on one integrated circuit. In the hierarchy of electronic components, the LPC43S67JET100E is a 32-bit embedded microcontroller, part of the Arm Cortex-M class of microcontrollers, and ultimately belongs to the broader semiconductor and embedded-computing category. Its dual-core architecture allows the Cortex-M4 core to execute application or network-control code while the Cortex-M0 subsystem handles peripheral management or real-time tasks, reducing the need for a separate microcontroller on complex boards.
Key capabilities include a 204 MHz Arm Cortex-M4/M0 processor configuration, 1 MB of flash, and 154 kB of SRAM. The Cortex-M0 subsystem supports the LPC43S6x architecture's division of work between the primary processor and dedicated peripheral handling. Ethernet and two high-speed USB interfaces make the device suitable for connected industrial, communications, and control equipment, while the quad SPI Flash Interface supports external serial-memory expansion. An AES engine provides hardware assistance for cryptographic operations, and the 16 kB EEPROM provides nonvolatile storage for configuration or calibration data.
The LPC43S6x integrates advanced configurable peripherals such as SCTimer/PWM and Serial General Purpose I/O, allowing designers to tailor timer channels, signal routing, and I/O behavior for application-specific timing and control requirements. This integration is especially useful in systems that need deterministic peripheral handling while the main Cortex-M4 core handles protocols, control logic, or higher-level software. The Ethernet interface also makes the MCU suitable for gateways and network-connected embedded equipment without requiring a separate communications processor.
Typical uses include industrial Ethernet controllers, USB-connected data acquisition equipment, building automation controllers, embedded gateways, motor and motion-control platforms, and connected test systems. The 100-TFBGA package supports compact designs but requires careful PCB layout with multiple power and ground connections. Designers should use the manufacturer's pin-description table, power-supply recommendations, and decoupling requirements when assigning the 100-ball land pattern and planning high-speed USB or Ethernet signal routing.
The main design trade-off is package density: the 9 x 9 mm TFBGA minimizes PCB area but complicates assembly, inspection, and prototype rework compared with a leaded package. Stable rails, short return paths, controlled impedance routing, and careful exposed-ball layout are therefore more important than in a large-outline controller. This page also organizes the device's pricing route, replacement options, comparison parameters, and practical integration guidance for faster engineering evaluation.
直接替換替代品,適用於 LPC43S67JET100E — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LPC43S67JET100E (相同外形與佔位) — 差異在於 On-Chip SRAM.
LPC43S67JET100
✅ 直接替換📋 參考替代品(不在目錄中)
LPC4337JET100E
✅ 直接替換聯絡詢價
查看資料表 →LPC4357JET100
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
LPC4370FET100E
✅ 直接替換聯絡詢價
查看資料表 →LPC43S67JET100B
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
LPC43S67JET100E 最大額定值與電氣特性
| Product Type | 32-bit dual-core microcontroller |
| Main Processor Core | Arm Cortex-M4/M0 |
| Maximum Processor Frequency | 204 MHz |
| Flash Memory | 1 MB (1M x 8) |
| On-Chip SRAM | Up to 154 kB |
| On-Chip EEPROM | 16 kB |
| Ethernet Interface | 1 Ethernet interface |
| High-Speed USB Interface | 2 high-speed USB interfaces |
| External Serial Flash Interface | Quad SPI Flash Interface |
| Crypto Accelerator | AES engine |
| Advanced Timer Peripheral | SCTimer/PWM |
| Configurable I/O Peripheral | Serial General Purpose I/O |
| 封裝 | 100-TFBGA (9 x 9 mm) |
| 安裝類型 | Surface mount |
| Packaging | Tray |
| RoHS 狀態 | RoHS code reported as Yes |
LPC43S67JET100E 100-tfbga (9 x 9 mm) 腳位配置指南
LPC43S67JET100E(100-tfbga (9 x 9 mm) 封裝)的腳位配置。 此數位 IC 包含 GPIO、通訊介面(UART、SPI、I2C)與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料: LPC43S67JET100E.
請參閱 資料表 以查看完整腳位配置。
典型應用
LPC43S67JET100E 適用於 6 應用s: Industrial Ethernet Gateways, USB Data Acquisition Equipment, Building Automation Controllers, Motor and Motion Control, Connected Embedded Test Systems, Secure Network Appliances.
Industrial Ethernet Gateways
The LPC43S67JET100E fits industrial Ethernet gateways because it combines a 204 MHz Arm Cortex-M4/M0 architecture with integrated Ethernet, 1 MB of flash, and up to 154 kB of SRAM. The Cortex-M4 core can execute protocol stacks and gateway logic while the Cortex-M0 subsystem manages timers, GPIO, and other peripherals. This dual-core arrangement allows deterministic I/O handling without forcing every interrupt-driven task onto the main processor. A key design consideration is to partition firmware and interrupt ownership carefully, then validate timing under sustained Ethernet traffic and industrial EMC conditions.
推薦
USB Data Acquisition Equipment
The LPC43S67JET100E is well suited to USB-connected data-acquisition equipment because it provides two high-speed USB interfaces alongside a 204 MHz Cortex-M4/M0 processor and substantial on-chip memory. One USB interface can support host or peripheral duties while the other serves a separate function, subject to the device's detailed mode configuration. The Cortex-M0 subsystem is useful for maintaining predictable sampling, trigger, and communication timing. Board design must preserve high-speed signal integrity through controlled-impedance routing, short return paths, and compliant connector and protection schemes.
推薦
Building Automation Controllers
The LPC43S67JET100E supports compact building-automation controllers that coordinate sensors, actuators, communications, and local control logic. Its 1 MB flash can hold application firmware and configuration data, while 154 kB of SRAM provides room for communication buffers and real-time state. Ethernet connectivity supports centralized monitoring, and the Cortex-M0 subsystem can service timing-sensitive peripheral operations while the Cortex-M4 core handles application logic. Designers should define deterministic update intervals and isolate network traffic from safety-critical timing paths during firmware validation.
推薦
Motor and Motion Control
The LPC43S67JET100E can be used in motor and motion-control subsystems where a high-performance control core and dedicated real-time subsystem are both valuable. Its 204 MHz Cortex-M4 core can execute motion algorithms, while the Cortex-M0 subsystem can manage timers, capture functions, and serial GPIO with predictable latency. The SCTimer/PWM resources support precise edge generation and period control. A practical implementation should separate control-loop timing from Ethernet or USB service tasks, verify PWM behavior at the worst-case operating condition, and include suitable gate drivers outside the MCU.
推薦
Connected Embedded Test Systems
The LPC43S67JET100E supports connected test and measurement systems that need substantial flash, real-time control, USB connectivity, and Ethernet communications in one compact package. The 1 MB flash stores firmware, test sequences, and calibration tables, while 154 kB of SRAM accommodates acquisition buffers and protocol state. Its dual-core organization allows one core to manage test sequencing and the other to service peripherals or communication timing. For sensitive analog measurement systems, separate the analog front end from the digital supply paths and use controlled grounding to prevent controller activity from disturbing acquired signals.
推薦
Secure Network Appliances
The LPC43S67JET100E is appropriate for compact network appliances that require Ethernet, USB service connectivity, and hardware-assisted cryptography. Its AES engine assists with cryptographic processing, while the 204 MHz Cortex-M4/M0 platform can divide network workloads from peripheral and security-monitor tasks. The 100-TFBGA package allows a dense implementation, but careful plane partitioning, impedance control, and power filtering are necessary to protect high-speed and security-sensitive paths. Firmware design should establish secure boot, key-management boundaries, fault recovery, and update procedures before production deployment.
推薦
推薦產品摘要
工程參考資料,適用於 LPC43S67JET100E — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LPC43S67JET100 | LPC4337JET100 | LPC4357JET100 | LPC4370FET100E |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 100-TFBGA (9 x 9 mm) | 100-TFBGA (9 x 9 mm) | 100-TFBGA (9 x 9 mm) | 100-TFBGA (9 x 9 mm) | 100-TFBGA (9 x 9 mm) |
主要差異化特點
- Dedicated Cortex-M0 subsystem supports concurrent peripheral management (對比LPC4370FET100E)
- Two high-speed USB interfaces expand peripheral connectivity (對比LPC4337JET100)
- Up to 154 kB SRAM supports richer communication and control buffers (對比LPC43S67JET100)
- Integrated connectivity reduces external controller demand (對比LPC4357JET100)
設計說明
Implement the 100-TFBGA power network by following NXP's recommended ball grouping, via arrangement, and capacitor placement. Place each decoupling capacitor directly between its associated device supply ball and the nearest ground reference, with very short loops. Avoid routing Ethernet, USB, or other high-speed nets across split planes, and confirm every package ball against the LPC43S67JET100 pin table before releasing artwork. Because the package is only 9 x 9 mm, assembly capability and X-ray inspection should be planned early rather than treated as production afterthoughts.
Treat Ethernet and high-speed USB routes as controlled-impedance transmission lines using the PCB fabricator's stack-up. Maintain continuous reference planes, minimize stub branches, and place termination or protection components where their effect on the edge rate is controlled. Isolate noisy switching nodes and regulator return currents from analog or measurement circuits. The controller's 204 MHz processing capability does not imply that every PCB trace should be treated as a high-speed clock route; instead, follow the interface-specific rise-time and impedance requirements in the manufacturer documentation.
Do not treat the LPC43S67JET100, LPC43S67JET100E, and other LPC43-family ordering codes as unconditional substitutions. Verify the temperature grade, qualification state, exposed-ball requirements, memory configuration, boot configuration, peripheral mapping, and package drawing. Likewise, verify the Cortex-M0 subsystem assignment and interrupt routing before reusing firmware between LPC43S6x devices. The closest alternative is the one that passes both the mechanical footprint comparison and the application-specific peripheral and qualification review.
Partition the MCU's digital supply paths carefully and follow the manufacturer's recommended voltage rails and capacitor values. Do not infer the complete power architecture from the headline 204 MHz specification because processor activity, enabled peripherals, USB, and Ethernet traffic affect instantaneous demand. Use the datasheet's absolute maximum ratings, recommended operating conditions, power-consumption tables, and layout example as the design basis. Validate startup, brownout behavior, and rail sequencing across temperature and the intended Ethernet and USB traffic conditions.
合規資訊
The product-comparison source reports a RoHS code of Yes for the LPC43S6x family. No separate REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration is stated for the exact LPC43S67JET100E ordering code.