Texas Instruments

LT1013AIP - Dual Precision Op Amp, 4V-44V, DIP-8 | TI

MPN: LT1013AIP ✓ सक्रिय
4 V to 44 V Vdss 8-pin PDIP Package
न्यूनतम ऑर्डर मात्रा: 1 |

LT1013AIP अवलोकन

The Texas Instruments LT1013AIP is a dual precision operational amplifier with a 4 V to 44 V supply range, low supply current, low noise, and high open-loop gain. The device is supplied in an 8-pin PDIP package designated for industrial temperature operation and through-hole PCB assembly. It contains two independent precision amplifier sections in an industry-standard dual-op-amplifier pin configuration.

A precision operational amplifier is a voltage-feedback amplifier designed to amplify small differential signals while minimizing offset voltage, input bias current, noise, and drift. The LT1013 belongs to the operational-amplifier hierarchy within analog signal-chain ICs, combining a high-impedance differential input stage with a low-distortion output stage. Its broad supply range makes it suitable for both low-voltage instrumentation and higher-voltage industrial signal chains.

The LT1013 family combines high gain with low supply current, low noise, and a low offset-voltage temperature coefficient. Manufacturer documentation identifies the family as a precision dual amplifier with performance suited to battery-powered precision instrumentation, strain-gauge signal conditioning, thermocouple amplification, instrumentation amplifiers, and 4 mA to 20 mA current-loop transmitters. The wide operating supply supports both single 5 V and dual positive and negative supply arrangements.

Each amplifier section operates independently, allowing simultaneous conditioning of two related signals or use as a single amplifier with the other section acting as a buffer. The industrial-grade through-hole package favors laboratory instruments, legacy industrial controllers, test equipment, and maintenance-friendly designs where socketed or hand-inserted assembly is useful. The 8-pin PDIP footprint also simplifies repair and retrofit work compared with fine-pitch surface-mount packages.

Typical applications include precision bridge and strain-gauge front ends, low-level sensor instrumentation, thermocouple and RTD signal conditioning, active filters, threshold detection, and buffered 4 mA to 20 mA current-loop outputs. Because the operating supply extends to 44 V, the amplifier can also support higher-voltage industrial interfaces when the surrounding circuit and protection network are properly rated.

When designing a new PCB, follow the manufacturer pin-description table for every connection and preserve the standard dual-op-amplifier footprint. Place input, feedback, and compensation components close to the relevant amplifier pins, and check the selected resistor and capacitor values against the stability requirements described in the LT1013 manufacturer datasheet.

This page organizes the LT1013AIP supply, packaging, pinout, drop-in alternatives, application fit, and design considerations into one engineering-focused reference. It also compares the exact MPN with legacy precision and general-purpose dual-op-amplifier alternatives so engineers can identify the closest replacement without assuming electrical equivalence.

के लिए ड्रॉप-इन विकल्प LT1013AIP — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

इस सीरीज़ के वेरिएंट

समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं LT1013AIP (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Mounting Type, Amplifier Type, Number of Channels, Package.

Texas Instruments
Amplifier Type: Precision / General Purpose
Number of Channels: 2 (Dual)
Package: 8-PDIP (P)
इसके साथ तुलना करें LT1013AIP →
Texas Instruments
Mounting Type: Through-hole PDIP
इसके साथ तुलना करें LT1013AIP →

LT1013IP

✅ ड्रॉप-इन
Texas Instruments
📦 PDIP-8
2 circuits · 4 V to 44 V · 550 uV maximum · Bipolar input · Extends to ground · Swings to ground while sinking current · Precision operational amplifier · Low-power operational amplifier

कीमत के लिए संपर्क करें

डेटाशीट देखें →

LT1013CP

✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित
Texas Instruments
📦 PDIP-8
2 (Dual) · Precision / General Purpose · 4 V to 44 V · ±2 V to ±22 V · 150 µV at 25°C · 2.5 µV/°C · 0.5 mA · Includes ground (V-)

कीमत के लिए संपर्क करें

डेटाशीट देखें →

LM158P

✅ ड्रॉप-इन
📦 PDIP-8
Uses the same 8-pin PDIP dual-amplifier arrangement, but offset voltage, offset drift, noise, bandwidth, and supply-current performance differ from the LT1013AIP precision specification.

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

MC1458P

✅ ड्रॉप-इन
Texas Instruments
📦 PDIP-8
2 channels · Dual general-purpose operational amplifier · 30 V · 1 MHz

कीमत के लिए संपर्क करें

डेटाशीट देखें →

OP221

✅ ड्रॉप-इन
📦 PDIP-8
Legacy precision dual amplifier in the industry-standard 8-pin arrangement; LT1013 provides upgraded noise and precision performance according to the product documentation.

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

LT1013AIP Maximum Ratings और Electrical Characteristics

Amplifier Type Dual precision operational amplifier
Number of Channels 2 channels
Supply Voltage Range 4 V to 44 V
Single-Supply Operation 5 V typical application
Dual-Supply Operation +/-15 V typical application
Voltage Noise Density 7.2 nV/sqrt(Hz) for the compared device family upgrade
Operating Temperature Grade Industrial grade
Package Type 8-pin PDIP
Package Code DIP
Package Shape Rectangular
Terminal Count 8
माउंटिंग प्रकार Through-hole
RoHS Compliance unknown
REACH Compliance unknown

LT1013AIP पिन कॉन्फ़िगरेशन

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
पिन 1 OUT A — Amplifier A output
पिन 2 IN A- — Inverting input of amplifier A
पिन 3 IN A+ — Non-inverting input of amplifier A
पिन 4 V- — Negative supply connection
पिन 5 IN B+ — Non-inverting input of amplifier B
पिन 6 IN B- — Inverting input of amplifier B
पिन 7 OUT B — Amplifier B output
पिन 8 V+ — Positive supply connection

सामान्य अनुप्रयोग

LT1013AIP के लिए उपयुक्त है 6 अनुप्रयोगs: Strain-Gauge Bridge Signal Conditioning, Thermocouple Instrumentation, 4 mA to 20 mA Current-Loop Transmitter, Precision Active Filtering, Battery-Powered Precision Instruments, Legacy Test and Measurement Equipment.

🏭

Strain-Gauge Bridge Signal Conditioning

The LT1013AIP fits low-level strain-gauge front ends because its precision architecture combines high gain with low noise and a low offset-voltage temperature coefficient. Place the amplifier close to the bridge sensor to limit pickup of interference before the millivolt-level differential signal is amplified. The 4 V to 44 V supply range supports both portable measurement instruments and industrial monitoring equipment, while the 8-pin PDIP package is convenient for laboratory and maintenance-oriented assemblies. Resistor networks and compensation capacitors should follow the application circuits in the LT1013 manufacturer datasheet to preserve bandwidth and stability.

🌡️

Thermocouple Instrumentation

A thermocouple produces a small differential voltage that requires stable, low-offset amplification. The LT1013AIP provides two precision amplifier sections for conditioning or differentially amplifying related low-level signals, with the 4 V to 44 V range allowing operation from compact battery-powered instruments to higher-voltage industrial panels. Place input protection, cold-junction compensation components, and feedback networks close to the relevant pins to minimize thermal gradients and noise pickup. Because thermocouple errors are often in the microvolt range, verify offset voltage, drift, bias current, and common-mode limits against the required measurement accuracy.

🏭

4 mA to 20 mA Current-Loop Transmitter

The LT1013 family is identified for 4 mA to 20 mA current-loop transmitters, making the LT1013AIP appropriate for precision conversion of sensor voltages into standard industrial loop current. The amplifier can condition the input while the second section buffers a reference or assists with output drive. Its broad 4 V to 44 V supply range supports protected industrial loops, although the complete circuit still requires current limiting and surge protection. Validate output swing, loop compliance voltage, and stability over the full supply range before connecting the transmitter to field wiring.

🔧

Precision Active Filtering

The LT1013AIP is suitable for low-frequency active filters where offset drift and noise can obscure weak sensor signals. Its dual precision architecture permits two amplifier sections to implement a second-order filter, instrumentation stage, or buffered active network without changing the 8-pin through-hole footprint. The 4 V minimum supply supports compact battery-operated analyzers, while the 44 V maximum rating offers flexibility in higher-voltage laboratory systems. Select resistor and capacitor values from the manufacturer application guidance, check each amplifier's stability with the chosen gain, and keep feedback components compact to minimize parasitic coupling.

🔋

Battery-Powered Precision Instruments

Low supply current makes the LT1013AIP suitable for battery-powered precision instruments where every milliamp affects operating time. The dual amplifier can support a complete low-level measurement channel, including a gain stage and output buffer, in one package. Its 4 V to 44 V supply range accommodates single 5 V portable systems as well as higher-voltage laboratory instruments. Designers should minimize board area to reduce leakage paths, use high-impedance guarding techniques for sensitive inputs, and confirm the total system current from both amplifier sections under the worst-case load.

🖥️

Legacy Test and Measurement Equipment

The 8-pin PDIP LT1013AIP is especially useful when repairing or extending older laboratory and industrial test equipment that uses through-hole analog circuits. The standard dual-amplifier arrangement simplifies mechanical replacement on existing boards, and the wide supply range covers both 5 V and higher-voltage analog sections. A careful replacement still requires checking pin functions, supply polarity, offset limits, compensation values, and temperature grade. Use the manufacturer datasheet when converting a surface-mount design or when the original assembly includes trim potentiometers and external compensation networks.

अनुशंसित उत्पादों का सारांश

What are the key specifications of LT1013AIP that engineers should know?
The LT1013AIP is a dual precision operational amplifier with a 4 V to 44 V supply range in an 8-pin PDIP package. The family combines high open-loop gain, low supply current, low noise, and a low offset-voltage temperature coefficient. According to the LT1013 manufacturer datasheet, it is intended for precision instrumentation from battery-powered systems to higher-voltage industrial interfaces. Two independent amplifier sections are provided in the conventional 8-pin dual-op-amplifier configuration, allowing differential signal conditioning, gain amplification, filtering, and buffering.
What is the LT1013AIP operating voltage range?
The LT1013AIP operates from 4 V to 44 V across its full supply range. The manufacturer lists both single 5 V and dual positive and negative supply operation, including a typical +/-15 V application. This broad range allows one amplifier family to serve low-voltage instrumentation and higher-voltage industrial signal chains. The supply rating also provides headroom for protected field-side interfaces, although external overvoltage protection remains necessary when transients exceed the specified maximum.
Where can I download the LT1013AIP datasheet PDF?
The official LT1013AIP datasheet PDF is available from the Texas Instruments product document at https://www.ti.com/lit/ds/symlink/lt1013.pdf. It describes the dual precision amplifier, electrical characteristics, package options, pin descriptions, and typical applications. Use the manufacturer PDF for design decisions because it contains the authoritative ordering information, recommended operating conditions, test conditions, and application circuits. The product landing page at https://www.ti.com/product/LT1013 provides additional ordering and quality information.
Where can I find the LT1013AIP pinout?
The LT1013AIP pinout is defined by the 8-pin PDIP drawing and pin-description table in the LT1013 manufacturer datasheet. Use that table when assigning PCB tracks because it identifies both amplifier sections, their inputs and outputs, the supply pins, and any special-function pins. The component is a through-hole 8-pin package, so a standard PDIP footprint can be used only after confirming the pin numbering against the datasheet drawing. Avoid assigning connections from a generic dual-op-amplifier outline without checking the specific LT1013 family diagram.
Is the LT1013AIP suitable for strain-gauge and thermocouple instrumentation?
Yes, the LT1013AIP is suitable for strain-gauge and thermocouple instrumentation because the LT1013 family is identified for precision signal conditioning, low noise, low supply current, and a low offset-voltage temperature coefficient. These characteristics help preserve microvolt-level sensor information during amplification. The 4 V to 44 V supply range supports both compact battery-powered instruments and higher-voltage industrial measurement systems. Actual front-end performance still depends on the selected gain, reference strategy, input protection, and thermal design.
What is the LT1013AIP difference between single and dual supply operation?
Single-supply operation places the LT1013AIP between a positive rail and ground, so input and output signals must remain above the usable output-swing region. Dual-supply operation uses positive and negative rails, allowing signals to be centered around ground and simplifying many instrumentation designs. The manufacturer describes the device with 5 V single-supply and +/-15 V dual-supply applications. For either arrangement, verify input common-mode range, output swing, decoupling, and grounding against the electrical characteristics in the LT1013 manufacturer datasheet.
Can LT1013IP replace LT1013AIP in an existing circuit?
LT1013IP is the closest same-footprint option for an existing LT1013AIP design, but it is the standard-temperature grade rather than the industrial-grade version identified for LT1013AIP. Both use the 8-pin PDIP package and the LT1013 dual-amplifier architecture. Before substitution, confirm the required ambient-temperature range, supply conditions, offset specification, and production availability. The package match alone does not guarantee equivalent temperature grade or lifecycle suitability in every operating environment.
What is the best drop-in replacement for LT1013AIP?
LT1013IP is generally the closest drop-in replacement because it retains the same family, dual-amplifier architecture, and 8-pin PDIP footprint while changing the temperature grade. It is a practical choice when the original board does not require industrial-temperature qualification. Legacy dual precision amplifiers such as LM158P and OP221 may also fit the standard 8-pin arrangement, but their offset, noise, drift, supply-current, and availability characteristics can differ. Verify the full operating envelope before approving any substitution.
What is the best Analog Devices equivalent for LT1013AIP?
The legacy Analog Devices precision dual-op-amplifier families commonly considered for LT1013 cross-referencing include the OP221 class, while Maxim and Burr-Brown equivalents are also represented in published cross-reference catalogs. Pin compatibility alone should not decide the replacement. Compare input offset voltage, offset drift, input bias current, noise density, gain-bandwidth product, supply current, output swing, and temperature grade. Request the current manufacturer documentation for the selected MPN and verify it against the original LT1013AIP operating conditions before releasing a production design.
LT1013AIP versus LM158P: which is better for precision measurement?
The LT1013AIP is the stronger choice when the design depends on precision-amplifier performance, especially low offset drift, low noise, and stable measurement of small sensor signals. LM158P belongs to the older general-purpose precision-amplifier family and shares the traditional 8-pin arrangement, but its input and output characteristics are not automatically identical. The comparison also depends on temperature grade and supply range. Use the manufacturer electrical tables for both devices and preserve the same PCB footprint only after checking every pin assignment.
When should I choose LT1013AIP instead of LT1013IP?
Choose LT1013AIP when the equipment must operate across an industrial temperature environment or when the original design specified that grade. Choose LT1013IP when the assembly is used in a benign indoor environment and lower cost or availability is more important than industrial temperature qualification. Both parts use the same 8-pin PDIP architecture, so the decision should not be based on PCB layout alone. Confirm operating temperature, supply voltage, offset limits, and any qualification requirements in the manufacturer documentation.
Is LT1013AIP suitable for a 4 mA to 20 mA current-loop transmitter?
Yes, the LT1013 family is specifically identified for 4 mA to 20 mA current-loop transmitters. Its precision characteristics help reduce error when amplifying the loop voltage and driving the protected output stage, while the wide supply range suits industrial loop circuits. A practical transmitter still needs input filtering, surge protection, output-current limiting, and compliance-voltage analysis. Check the amplifier output swing and drive capability against the complete loop circuit before finalizing the design.
What can replace LT1013AIP on a through-hole PCB?
LT1013IP is the most direct replacement for LT1013AIP because it uses the same 8-pin PDIP package and belongs to the same dual precision amplifier family. Legacy alternatives with standard dual-op-amplifier pin arrangements may also fit the board mechanically, but electrical equivalence depends on offset, drift, noise, bandwidth, supply current, and temperature rating. Use the pin-description table for every candidate rather than assuming that all 8-pin dual amplifiers are interchangeable. Verify the replacement across the full supply and temperature range before production use.
Is LT1013AIP the same as MC1458P or OP221?
No. The LT1013AIP is a modern precision dual amplifier that upgrades the performance of legacy devices such as the MC1458 and OP221, but sharing a package does not make the electrical specifications identical. The LT1013 family emphasizes high gain, low supply current, low noise, and low offset-voltage temperature coefficient. Before treating MC1458P or OP221 as replacements, compare their input offset, drift, bias current, noise, bandwidth, supply range, and temperature grade with the exact operating requirements of the circuit.
Where to buy LT1013AIP online and what is its lead time?
Use the Request a Quote form on this page to ask about LT1013AIP availability, lot sourcing, and the current lead time from XAIPART. Because inventory and scheduling change frequently, request a written quotation for the exact manufacturer part number and required quantity. The 8-pin PDIP package is normally ordered as a standard industrial-grade device, but the confirmation should include the suffix, package, temperature rating, and shipment date. Submit your requirement before committing a production schedule.

के लिए इंजीनियरिंग संदर्भ डेटा LT1013AIP — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose the LT1013AIP when the design needs a dual precision amplifier, a 4 V to 44 V supply range, low supply current, and industrial temperature operation in an 8-pin PDIP package. LT1013IP is the most direct option when the same family and footprint are needed but industrial temperature qualification is unnecessary. LT1013CP is appropriate for commercial-temperature, cost-sensitive assemblies. LM158P, MC1458P, and OP221 may fit legacy 8-pin boards, but their offset, drift, noise, bandwidth, supply-current, and temperature characteristics can differ, so each requires a full electrical comparison. For new precision-measurement designs, favor the LT1013AIP when low-offset, low-noise performance and broad supply headroom justify the qualification requirements. For repair work, first verify the original pin arrangement, supply voltage, temperature range, compensation components, and any trim settings before approving a substitute.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद LT1013IP LT1013CP LM158P MC1458P OP221
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments onsemi Analog Devices
Package PDIP-8 PDIP-8 - same PDIP-8 - same PDIP-8 - same PDIP-8 - same PDIP-8 - same
Amplifier Configuration Dual precision operational amplifier Dual precision operational amplifier Dual precision operational amplifier Dual precision operational amplifier Dual operational amplifier Dual precision operational amplifier
Mounting Type Through-hole Through-hole Through-hole Through-hole Through-hole Through-hole
Primary Application Focus Precision instrumentation and signal conditioning Precision instrumentation and signal conditioning Precision instrumentation and signal conditioning Legacy precision signal conditioning Legacy general-purpose amplification Legacy precision signal conditioning

मुख्य विशेषताएँ

  • Combines a 44 V maximum supply with low-power precision amplification (बनामMC1458P)
  • Upgraded noise performance within the legacy dual-op-amplifier ecosystem (बनामOP221)
  • Industrial temperature grade in a serviceable through-hole package (बनामLT1013IP)
  • Two precision amplifier sections in the standard 8-pin configuration (बनामLM158P)

डिज़ाइन नोट्स

Keep the feedback network, input resistors, and compensation capacitors close to their associated LT1013 pins. Sensitive bridge or thermocouple inputs should have a short path from the connector to the amplifier, with guard techniques applied where leakage from PCB contamination could affect a high-impedance source. Place the bypass capacitor adjacent to the positive supply pin and connect the negative supply return directly into the ground plane. Because the LT1013AIP uses a legacy 8-pin PDIP footprint, pay particular attention to solder bridging and contamination between the closely spaced input leads.

Do not treat every 8-pin dual operational amplifier as an electrical substitute for the LT1013AIP. A mechanically identical footprint can still differ in offset voltage, drift, bias current, noise, bandwidth, stability, supply current, and output-swing behavior. The most common retrofit error is replacing a precision instrumentation amplifier with a general-purpose unit whose low-frequency error is too large for the measurement specification. Compare the candidate against the complete LT1013 operating envelope and confirm the temperature grade. Also avoid applying the 44 V maximum rating to transient protection; add appropriate clamping and surge protection where the field connection is exposed.

Estimated: supply current depends on the output stage, supply voltage, input common-mode condition, and whether both amplifier sections are active, so obtain the operating-current curve from the LT1013 manufacturer datasheet before sizing a battery or regulator. For battery-powered operation, total current is approximately the sum of both sections plus the external bias and feedback-network current. A practical design should reserve regulator headroom for transient load steps and include a local bypass capacitor at the supply pin. Do not use a nominal-current estimate as the sole basis for a long-term power budget.

When adapting an existing board, verify the LT1013AIP pin-description table and package drawing before assigning tracks, particularly around the two amplifier sections and the supply connections. Keep output routing away from input and reference nodes, particularly in high-gain configurations where capacitive coupling can create oscillation. Use a single low-impedance ground return for both amplifier sections rather than splitting analog and return currents through long board traces. For retrofit work, inspect the existing board for leaked flux and contamination before installing the replacement through-hole device.

अनुपालन जानकारी

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

The component is an industrial-grade dual operational amplifier in a through-hole PDIP package. No specific RoHS, REACH, halogen-free, conflict-minerals, or automotive qualification statement was located, so those fields remain unknown.

डेटा सत्यापन तिथि: 2026-11-14 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

lt1013 pdf lt1013 pinout LT1013AIP datasheet LT1013AIP pinout LT1013AIP PDIP-8 LT1013AIP operating voltage LT1013AIP drop-in replacement LT1013AIP equivalent LT1013AIP vs LT1013IP LT1013AIP precision instrumentation LT1013AIP strain gauge amplifier LT1013AIP price Texas Instruments LT1013AIP how to replace LT1013AIP

संबंधित कंपोनेंट्स और शब्द

Texas Instruments LT1013AIP LT1013IP LT1013CP LM158P MC1458P OP221 dual precision operational amplifier precision op amp voltage-feedback amplifier signal-conditioning IC analog signal chain instrumentation amplifier strain-gauge signal conditioner thermocouple amplifier 4 mA to 20 mA current-loop transmitter active filter JFET-input operational amplifier PDIP-8 through-hole package 4 V to 44 V supply 5 V single supply plus or minus 15 V dual supply offset voltage temperature coefficient
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें