LT1013CJ8 - Dual Precision Op Amp, CDIP | Analog Devices
MPN: LT1013CJ8 ✓ सक्रियLT1013CJ8 अवलोकन
An operational amplifier, or op amp, is a high-gain differential amplifier that uses negative feedback to create a stable closed-loop gain. The LT1013 belongs to the precision amplifier hierarchy: operational amplifier, analog amplifier, and then integrated circuit. Its industry-standard 8-pin configuration supports conventional dual-amplifier layouts without requiring a specialized footprint.
The LT1013 provides two precision amplifiers in one package. Key operating characteristics include support for ±15 V supplies, single 5 V operation, and a total supply range extending to ±22 V, corresponding to 44 V across the supply terminals. The device is specified for instrumentation, strain-gauge conditioning, thermocouple amplification, 4 mA-to-20 mA current-loop transmitters, active filters, threshold detection, and precision gain blocks.
Its precision architecture is intended to reduce offset-related error in slow analog signals. This makes the amplifier useful where input-source impedance, sensor leakage, or thermal drift can otherwise create measurement errors. The single-supply ability to include ground in the input range is especially useful for battery-powered systems and sensors whose output can approach the lower rail.
Typical applications include low-level sensor amplification, process-control instrumentation, current-loop receivers, precision filters, and multiple gain stages requiring two matched amplifier channels. The dual configuration reduces package count in multi-channel analog front ends while retaining independent inputs, outputs, and supply pins.
For reliable operation, verify the input and output common-mode range at the selected supply voltage and load. Decoupling capacitors should be placed close to the supply pins, and sensitive bias-current measurements require guarded PCB traces, clean connectors, and leakage control around the input terminals.
This page combines the LT1013CJ8 device identity, package information, manufacturer application coverage, verified source links, drop-in-family alternatives, and practical selection guidance for precision analog design work.
के लिए ड्रॉप-इन विकल्प LT1013CJ8 — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस सीरीज़ के वेरिएंट
समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं LT1013CJ8 (समान फॉर्म फैक्टर और फुटप्रिंट).
LT1013AJ8
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित📋 संदर्भ विकल्प (कैटलॉग में नहीं)
LT1013ACJ8
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित📋 संदर्भ विकल्प (कैटलॉग में नहीं)
LT1013CJ8 Maximum Ratings और Electrical Characteristics
| कोई specifications उपलब्ध नहीं |
LT1013CJ8 पिन कॉन्फ़िगरेशन
| पिन 1 | OFFSET NULL A — Amplifier A offset null |
| पिन 2 | INVERTING INPUT A — Inverting input for amplifier A |
| पिन 3 | NONINVERTING INPUT A — Noninverting input for amplifier A |
| पिन 4 | V- — Negative supply connection |
| पिन 5 | NONINVERTING INPUT B — Noninverting input for amplifier B |
| पिन 6 | INVERTING INPUT B — Inverting input for amplifier B |
| पिन 7 | OUTPUT B — Output for amplifier B |
| पिन 8 | OUTPUT A — Output for amplifier A |
सामान्य अनुप्रयोग
LT1013CJ8 के लिए उपयुक्त है 6 अनुप्रयोगs: Strain-Gauge Signal Conditioning, Thermocouple Instrumentation, 4 mA to 20 mA Current Loop, Precision Active Filters, Battery-Powered Instrumentation, Precision Gain and Threshold Detection.
Strain-Gauge Signal Conditioning
The LT1013CJ8 is suitable for conditioning the small differential voltage generated by a strain-gauge bridge in industrial weighing, force measurement, and pressure equipment. Its dual precision topology allows one amplifier to amplify the bridge signal while the second handles gain, filtering, or excitation-related buffering within the same 8-pin CERDIP package. Operation from ±15 V supports legacy industrial analog circuits with substantial headroom. The single-supply input range extending to ground is also useful when redesigning the front end for lower-voltage operation. Bridge excitation, common-mode voltage, and output range must be checked together so that neither input nor output exceeds the amplifier's allowable operating region.
अनुशंसित
Thermocouple Instrumentation
The LT1013CJ8 can serve in low-level thermocouple measurement circuits where microvolt-to-millivolt signals require stable gain and low offset. The two amplifier channels can implement a difference stage or provide amplification and filtering for a differential sensor interface. The device's support for ±15 V permits direct use in classic industrial instrumentation without a lower-voltage translation stage. When designing the circuit, evaluate input bias-current error, source impedance, input common-mode range, and thermal gradients across the PCB because these effects can dominate a thermocouple's small output. Stable grounding and guard techniques are especially important when the source impedance is high.
अनुशंसित
4 mA to 20 mA Current Loop
The LT1013CJ8 is appropriate for precision current-loop receiver and transmitter interfaces used in process-control systems. Its two independent amplifiers can support gain and filtering functions in a compact analog channel, while operation from ±15 V or a single 5 V supply allows compatibility with both traditional plant equipment and modern embedded instrumentation. A current-loop implementation must preserve the loop's compliance voltage and account for the amplifier's input and output ranges when setting the gain. Low-offset behavior is valuable in a receiver because it shifts the measured current directly into the reconstructed process variable. Power-supply bypassing and grounded reference returns remain essential for stable loop accuracy.
अनुशंसित
Precision Active Filters
The LT1013CJ8 is suitable for active-filter stages that require predictable gain and low offset in instrumentation and test circuits. Two amplifiers in one 8-pin CERDIP package allow a second-order filter and an additional gain or buffer stage without using two separate packages. The LT1013's specified single 5 V operation is useful for compact low-voltage systems, while its ground-referenced input capability simplifies circuits that process signals near 0 V. Stable filter performance depends on resistor and capacitor tolerances, output loading, and the amplifier's small-signal behavior across the intended frequency range. Confirm bandwidth, slew rate, and output-current requirements from the manufacturer data sheet before selecting the final external components.
अनुशंसित
Battery-Powered Instrumentation
The LT1013CJ8 can be used in battery-powered precision measurement equipment where low-level signals must be amplified close to the lower supply rail. The manufacturer specifies single 5 V operation and notes that the single-supply input range extends to ground, making the device useful for portable sensor interfaces with a near-zero common-mode voltage. The two amplifier channels can reduce component count by combining amplification and buffering or by implementing two related measurement channels. Because operation near the supply rails can narrow usable input and output ranges, evaluate the sensor's full output span at startup, discharge, and temperature extremes. Low-power designs should also account for quiescent current and external filter-component leakage.
अनुशंसित
Precision Gain and Threshold Detection
The LT1013CJ8 fits precision gain blocks and threshold-detection circuits where predictable signal levels are required. One channel can amplify or buffer a sensor output, while the second performs a second gain stage or comparison function around a reference voltage. The ceramic-DIP package is suitable for through-hole industrial, laboratory, and legacy control boards where long-term availability and conventional assembly are priorities. Design the signal path so the amplifier never approaches its output limits during threshold transitions, and use stable reference components to prevent detection-point drift. Decoupling, input guarding, and clean power grounding are especially important when the detected signal has a low amplitude or high source impedance.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा LT1013CJ8 — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | LT1013AJ8 | LT1013ACJ8 |
|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Package | 8-pin CERDIP | 8-pin CERDIP | 8-pin CERDIP |
| Amplifier Count | 2 | 2 | 2 |
| Product Type | Dual precision operational amplifier | Dual precision operational amplifier | Dual precision operational amplifier |
| Temperature Grade | 0 C to 70 C | -55 C to 125 C | -40 C to 125 C |
| Primary Applications | Instrumentation, strain gauges, thermocouples, current loops, filters, and gain blocks | Precision instrumentation and signal conditioning | Precision instrumentation and automotive-grade signal conditioning |
मुख्य विशेषताएँ
- Two precision amplifiers in one ceramic-DIP package (बनामLT1014AMJ8)
- Commercial temperature grade (बनामLT1013AJ8)
- Automotive temperature-range alternative (बनामLT1013ACJ8)
डिज़ाइन नोट्स
Place the supply-decoupling capacitor immediately between the V+ and V- pins, with a short return path to the ground plane. Keep input traces short and away from the offset-null and supply pins. For high-impedance sensor inputs, use guarding and minimize leakage from PCB contamination and connectors; otherwise bias-current error can obscure the intended precision measurement.
Verify the common-mode input range and output swing at the exact supply voltage, load current, and temperature. The single-supply input range extending to ground does not mean that the amplifier can swing rail-to-rail at the output. Include startup, sensor-offset, and supply-tolerance margins so that the output never approaches its functional boundary.
For precision gain stages, calculate the maximum total gain from the amplifier's small-signal bandwidth and verify that the intended signal and any switching components remain within that limit. Stable operation also depends on correct feedback topology and suitable compensation values. Use the manufacturer data sheet's gain-bandwidth and stability guidance when selecting feedback components.
अनुपालन जानकारी
The LT1013CJ8 is not documented as an AEC-Q100-qualified automotive device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status are unknown.