LT1126CJ8 - 65MHz Dual Op Amp | Analog Devices
MPN: LT1126CJ8 ✓ सक्रियLT1126CJ8 अवलोकन
An operational amplifier is a voltage-feedback amplifier that uses high open-loop gain to compare an input signal with a feedback network. The LT1126 belongs to the precision-op-amp, voltage-feedback amplifier, signal-conditioning IC, and power-management-support hierarchy. Decompensation deliberately reduces closed-loop stability at lower gain in exchange for faster large-signal behavior and wider bandwidth, making this family useful in high-speed instrumentation and signal-processing paths.
The principal performance figures are a 65 MHz gain-bandwidth product and an 11 V/µs slew rate. Its dual configuration supports two independent signal channels, while the 8-CERDIP package provides through-hole construction for industrial and legacy equipment. The family description also identifies low-voltage noise, high voltage gain, low offset voltage, and low supply-current-per-amplifier characteristics. These features make the LT1126 appropriate where amplifier accuracy must coexist with rapid signal transitions.
Decompensated operation requires the circuit designer to select a suitable noise gain and verify stability at the intended closed-loop gain. At unity gain, the amplifier is typically decompensated and may require external compensation or a higher noise-gain setting. Component tolerances, capacitive loading, and the feedback network should therefore be evaluated together rather than relying only on the nominal gain-bandwidth product.
Typical uses include low-level signal conditioning, precision measurement systems, active filtering, data acquisition, instrumentation, and industrial control. The dual package can also reduce board area when a design needs two amplifiers with consistent performance. Its combination of 65 MHz bandwidth and 11 V/µs slew rate is particularly relevant to wideband transimpedance, buffer, and feedback-network designs where the LT1124 or LT1125 would provide less AC performance.
Designers should use the manufacturer pin-description table when assigning PCB connections and should confirm stability at every intended gain and capacitive-load condition. Input and output buffering, power-supply bypassing, grounding, and output-load limits remain important. The ceramic DIP construction also requires adequate board spacing and through-hole assembly planning, particularly where long leads can add parasitic inductance at high frequency.
This product record combines the verified LT1126 family specifications with application-focused engineering guidance, practical stability considerations, package information, and a comparison of available same-family temperature-grade alternatives. It is intended to help engineers evaluate the LT1126CJ8 for dual-channel precision signal paths while distinguishing the industrial-grade CJ8 version from related ceramic-DIP variants.
के लिए ड्रॉप-इन विकल्प LT1126CJ8 — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
LT1126EJ8
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित📋 संदर्भ विकल्प (कैटलॉग में नहीं)
LT1126GJ8
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित📋 संदर्भ विकल्प (कैटलॉग में नहीं)
LT1126CJ8 Maximum Ratings और Electrical Characteristics
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Circuits | 2 circuits |
| टोपोलॉजी | Decompensated voltage-feedback amplifier |
| Gain-Bandwidth Product | 65 MHz |
| Slew Rate | 11 V/µs |
| पैकेज | 8-CERDIP |
| माउंटिंग प्रकार | Through-hole |
| Number of Terminals | 8 terminals |
| Package Shape | Rectangular |
| Temperature Grade | Industrial |
LT1126CJ8 rectangular पिन कॉन्फ़िगरेशन गाइड
LT1126CJ8 (rectangular पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस एनालॉग कंपोनेंट में इनपुट, आउटपुट और पावर सप्लाई पिन हैं। ऑफ़सेट नल, कम्पनसेशन और एनेबल पिन कॉन्फ़िगरेशन के लिए निर्माता डेटाशीट देखें। सिग्नल कंडीशनिंग और एम्प्लीफ़ायर सर्किट के लिए आदर्श।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: LT1126CJ8.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
LT1126CJ8 के लिए उपयुक्त है 6 अनुप्रयोगs: Precision Instrumentation Signal Conditioning, Active Filtering and Frequency Response, Wideband Data Acquisition, Low-Level Sensor Amplification, Industrial Control and Monitoring, Fast Buffering and Driver Circuits.
Precision Instrumentation Signal Conditioning
The LT1126CJ8 fits instrumentation front ends that must amplify small sensor signals while preserving fast transient performance. Its 65 MHz gain-bandwidth product provides bandwidth for signals well beyond audio frequencies, and the 11 V/µs slew rate limits large-signal distortion. The dual configuration allows one amplifier to condition a measurement and another to perform a related reference or buffer function. Because the device is decompensated, the engineer must select the required noise gain and verify compensation using the Analog Devices stability guidance before production release.
अनुशंसित
Active Filtering and Frequency Response
The LT1126CJ8 is suitable for wideband active filters where the LT1124 and LT1125 would offer less AC performance. Its 65 MHz gain-bandwidth product leaves more bandwidth for closed-loop filter sections, while the 11 V/µs slew rate improves handling of large or fast signals. The two amplifiers can implement a matched pair of filter or buffering stages. Component tolerances and noise gain must be selected carefully because a decompensated amplifier can require a different closed-loop gain or compensation network than a unity-gain-stable precision op amp.
अनुशंसित
Wideband Data Acquisition
The LT1126CJ8 can serve as the high-speed analog front end of a data-acquisition system when sampling bandwidth and settling behavior are important. A gain-bandwidth product of 65 MHz provides substantially more open-loop bandwidth than conventional precision amplifiers, and the 11 V/µs slew rate helps the output stage drive the required voltage excursion. Two amplifiers can provide simultaneous or sequential channels. The system designer should account for amplifier stability, sampling noise, input capacitance, and the dynamic range available from the downstream converter.
अनुशंसित
Low-Level Sensor Amplification
The LT1126CJ8 is appropriate for low-level sensor amplifiers that require both precision DC behavior and improved alternating-current response. The family combines low voltage noise, low offset voltage, and high voltage gain with a 65 MHz gain-bandwidth product, allowing sensor signals to be amplified without immediately forcing the circuit into a bandwidth-limited precision amplifier implementation. The dual package can handle a sensor channel and a reference channel, but bias-current error, input-common-mode range, sensor capacitance, and the required noise gain must all be evaluated against the operating conditions.
अनुशंसित
Industrial Control and Monitoring
The LT1126CJ8 is useful in industrial monitoring equipment that must process control signals rapidly while retaining the DC precision expected from instrumentation amplifiers. The industrial temperature-grade ordering code is suitable for evaluation against the product's environmental requirements, and the 8-CERDIP package supports through-hole assembly in legacy or industrial-control platforms. Two amplifiers can implement differential, gain, or buffer functions. Because the amplifier is decompensated, the feedback topology must preserve the required stable noise gain across temperature, supply, and component-tolerance variations.
अनुशंसित
Fast Buffering and Driver Circuits
The LT1126CJ8 can be used as a high-speed buffer or driver when the circuit benefits from the family's 11 V/µs slew rate and 65 MHz gain-bandwidth product. These characteristics are useful when driving a moderate load, isolating a sensitive source, or creating a higher-bandwidth signal path in a mixed analog system. The dual package provides two independent amplifiers for buffering and gain functions. Output-current capability, capacitive-load stability, settling time, and the external compensation requirements must be checked in the manufacturer datasheet before assigning the device to a specific load.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा LT1126CJ8 — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | LT1126EJ8 | LT1126GJ8 |
|---|---|---|---|
| Package | 8-CERDIP | 8-CERDIP | 8-CERDIP |
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Number of Amplifiers | 2 circuits | 2 circuits | 2 circuits |
| Gain-Bandwidth Product | 65 MHz | 65 MHz | 65 MHz |
| Slew Rate | 11 V/µs | 11 V/µs | 11 V/µs |
| Amplifier Architecture | Decompensated | Decompensated | Decompensated |
| Mounting Type | Through-hole | Through-hole | Through-hole |
| Number of Terminals | 8 terminals | 8 terminals | 8 terminals |
| Temperature-Grade Suffix | CJ8 | EJ8 | GJ8 |
मुख्य विशेषताएँ
- Higher AC performance than the LT1124 dual family (बनामLT1124)
- Two amplifiers share one ceramic-DIP package (बनामSingle-amplifier ceramic-DIP alternatives)
- Same-footprint temperature-grade choices (बनामLT1126EJ8)
डिज़ाइन नोट्स
Do not assume unity-gain stability. The LT1126 is decompensated, so the feedback network must establish the required stable noise gain. Follow the compensation guidance in the Analog Devices LT1126 datasheet and verify the final circuit with realistic tolerances and capacitive loading. A feedback change intended to improve signal gain can therefore make the amplifier oscillate or settle more slowly if compensation is not revisited.
Use the manufacturer pin-description table to assign the 8-CERDIP connections, and place local supply bypassing close to the device power pins. Keep analog input and feedback traces short, maintain a continuous ground reference, and route high-impedance nodes away from switching nodes. The through-hole ceramic package offers assembly flexibility, but lead inductance and long PCB traces can degrade stability at the LT1126's high bandwidth.
Treat the 65 MHz gain-bandwidth product and 11 V/µs slew rate as coupled design targets. Small-signal bandwidth does not by itself guarantee clean large-signal behavior, and the usable result also depends on gain, load capacitance, output amplitude, compensation, and settling tolerance. Use oscilloscope measurements at the intended output range and test the assembled PCB because parasitic capacitance and long feedback paths can change the response.
अनुपालन जानकारी
The product listing identifies an industrial-grade dual op amp in an 8-CERDIP package, but it does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status.