Analog Devices

LT1462CN8 - Dual Micropower JFET Op Amp | Analog Devices

MPN: LT1462CN8 ✓ सक्रिय
45 µA Vdss 1 pA Id 8-pin PDIP Package Within 1.5 V Memory
न्यूनतम ऑर्डर मात्रा: 1 |

LT1462CN8 अवलोकन

The Analog Devices LT1462CN8 is a dual micropower JFET-input operational amplifier with a maximum supply current of 45 µA per amplifier, typical input bias current of 1 pA, and an 8-pin PDIP package. It combines low power consumption with picoampere input bias current for precision, high-impedance circuit designs. The device is unity-gain stable with capacitive loads up to 10 nF and can operate with load values up to 10 kΩ.

An operational amplifier is a voltage-gain building block used to amplify small signals, buffer sensors, perform active filtering, and implement analog control functions. A JFET-input operational amplifier uses junction field-effect transistors at its input stage, providing very low input bias current. Within the broader hierarchy, the LT1462CN8 is an amplifier IC, specifically a precision-grade dual JFET operational amplifier designed for low-power analog signal conditioning.

The LT1462 family's defining characteristic is its combination of low power and very high input impedance. Each amplifier draws no more than 45 µA of supply current, while its typical input bias current is only 1 pA. These characteristics are useful when measuring signals from high-impedance sources because the amplifier contributes minimal loading to the source. The dual configuration also permits two independent amplifier channels in one package.

According to the Analog Devices product information, the LT1462 is unity-gain stable for capacitive loads up to 10 nF. This allows direct placement of up to 10 nF at the output without adding a separate isolation resistor in many applications. The output can also drive a 10 kΩ load to within 1.5 V of either supply rail, making the amplifier suitable for low-voltage instrumentation where output headroom matters.

Typical uses include precision sensor interfaces, low-level signal conditioning, photodiode amplifiers, capacitive transducers, battery-powered measurement systems, and analog filters. Because the device combines two channels, it can also implement differential, instrumentation, or active-filter topologies when a suitable resistor network and common-mode range are acceptable.

When designing around the LT1462CN8, account for the 1.5 V output headroom at a 10 kΩ load and verify the signal's common-mode range at the chosen supply voltage. Decoupling capacitors should be placed close to the supply pins, and sensitive input traces should be kept short and away from switching nodes to minimize leakage and pickup.

This page combines the manufacturer's published performance highlights with package details, application guidance, and a structured engineering comparison. It is intended to help designers evaluate the LT1462CN8 for low-power, high-impedance analog designs while recognizing that final circuit performance depends on supply voltage, load, source impedance, stability, and output-headroom requirements.

के लिए ड्रॉप-इन विकल्प LT1462CN8 — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

इस उत्पाद के लिए कोई drop-in alternatives उपलब्ध नहीं।

विकल्प अनुरोध करें

LT1462CN8 Maximum Ratings और Electrical Characteristics

Amplifier Type Dual JFET-input operational amplifier
Number of Channels 2 channels
Number of Amplifiers 2 amplifiers
Input Stage JFET
Maximum Supply Current per Amplifier 45 µA
Typical Input Bias Current 1 pA
Unity-Gain Stability Capacitive Load 10 nF
Output Load Condition 10 kΩ
Output Swing from Either Supply Rail Within 1.5 V
पैकेज 8-pin PDIP
माउंटिंग प्रकार Through-hole

LT1462CN8 8-pin pdip पिन कॉन्फ़िगरेशन गाइड

LT1462CN8 (8-pin pdip पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस एनालॉग कंपोनेंट में इनपुट, आउटपुट और पावर सप्लाई पिन हैं। ऑफ़सेट नल, कम्पनसेशन और एनेबल पिन कॉन्फ़िगरेशन के लिए निर्माता डेटाशीट देखें। सिग्नल कंडीशनिंग और एम्प्लीफ़ायर सर्किट के लिए आदर्श।

LT1462CN8 के लिए 8-pin pdip पैकेज पिनआउट आरेख

इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: LT1462CN8.

देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।

सामान्य अनुप्रयोग

LT1462CN8 के लिए उपयुक्त है 6 अनुप्रयोगs: Precision Photodiode Amplification, High-Impedance Sensor Signal Conditioning, Battery-Powered Measurement, Low-Level Analog Filtering, Capacitive Transducer Readout, Industrial Low-Level Signal Acquisition.

📷

Precision Photodiode Amplification

The LT1462CN8 is suitable for photodiode and other high-impedance transimpedance front ends because its typical input bias current is only 1 pA. A JFET input stage contributes minimal current to the source, reducing error in currents that may be much smaller than the amplifier's signal current. Both channels can support a two-amplifier instrumentation arrangement when required. The designer should still calculate the transimpedance feedback value, bandwidth, noise contribution, and compensation needed for the photodiode capacitance. Unity-gain stability up to 10 nF helps with limited load capacitance, while the 1.5 V output headroom at a 10 kΩ load defines how close to the rails the output can operate.

🧩

High-Impedance Sensor Signal Conditioning

The LT1462CN8 fits electrochemical, capacitive, and resistive sensors whose source impedance could be disturbed by amplifier input bias current. With a typical input bias current of 1 pA and a dual 8-pin PDIP package, it can provide two conditioned channels without using separate single amplifiers. Each channel draws no more than 45 µA, which is valuable in battery-operated measurement systems. Input common-mode voltage, offset voltage, and noise must remain within the limits of the chosen supply configuration. The available 10 nF capacitive-load stability is useful when sensor wiring introduces capacitance, although long cables or highly capacitive transducers may require a dedicated isolation resistor.

🔋

Battery-Powered Measurement

The LT1462CN8 is a practical choice for portable measurement equipment where amplifier power can dominate the battery budget. Its maximum supply current of 45 µA per amplifier limits the current demand of each active channel, while the dual configuration can implement gain, filtering, or signal conversion stages in one package. At low supply voltages, however, output headroom must be planned carefully: the output reaches only within 1.5 V of either rail with a 10 kΩ load. Confirm that the sensor signal and required output span fit the available supply voltage, and include a practical power budget rather than relying only on the per-amplifier maximum current.

⚡

Low-Level Analog Filtering

The LT1462CN8 can serve as an active element in low-frequency analog filters built around high-impedance sources. Picoampere-level typical input bias reduces excitation-current error in sensitive filter stages, and unity-gain stability supports direct operation with capacitor networks up to 10 nF. The dual amplifier allows Sallen-Key, multiple-feedback, or related topologies without requiring two packages. Stability at the nominal unity-gain setting does not mean every feedback network is unconditionally stable, so resistor and capacitor values should be evaluated for the intended closed-loop gain. Output swing and common-mode limits must also be checked when the filter uses most of the available supply range.

📡

Capacitive Transducer Readout

The LT1462CN8 is well matched to capacitive transducers because its 1 pA typical input bias produces very little input-current burden, while the amplifier remains unity-gain stable with capacitive loads up to 10 nF. These properties help preserve the integrity of charge-sensitive and frequency-based sensor signals. A practical design should still include input protection, defined grounding, and any required noise or drift compensation. The 8-pin PDIP package through-hole format can also suit prototype instrumentation and repair work where socketed DIP assembly is preferred. Confirm the complete electrical and pin details against the official LT1462 documentation before laying out the PCB.

🏭

Industrial Low-Level Signal Acquisition

The LT1462CN8 can serve in industrial signal-acquisition modules that combine sensor inputs with low-power analog processing. Its dual-channel configuration supports differential or sequential sensing, the JFET input stage limits source loading, and the 45 µA maximum supply current per amplifier supports compact low-power designs. Unity-gain stability for loads up to 10 nF is particularly helpful around cables, connector capacitance, and compact sensor interfaces. Industrial suitability depends on the exact operating-temperature grade, supply range, and compliance requirements rather than package format alone. Keep sensitive inputs away from switching nodes, use short traces, and place bypass capacitors close to the supply pins.

What is the LT1462CN8?
The LT1462CN8 is a dual micropower JFET-input operational amplifier from Analog Devices, packaged in an 8-pin PDIP configuration. According to the Analog Devices LT1462 product information, each amplifier consumes no more than 45 µA and has a typical input bias current of 1 pA. These characteristics make it appropriate for high-impedance precision signal-conditioning circuits operating from low-power supplies.
What are the key specifications of LT1462CN8?
The LT1462CN8 provides two JFET-input amplifier channels, 45 µA maximum supply current per amplifier, 1 pA typical input bias current, and unity-gain stability with capacitive loads up to 10 nF. Analog Devices also specifies that the output can swing to within 1.5 V of either supply when driving a 10 kΩ load. Its package is the 8-pin PDIP.
What is the input bias current of the LT1462CN8?
The LT1462CN8 has a typical input bias current of 1 pA per amplifier. According to the Analog Devices LT1462 product page, this picoampere input bias combines with a maximum supply current of 45 µA per amplifier. Very low input bias current reduces the loading applied to high-impedance sensors and makes the dual amplifier useful in precision measurement front ends.
Is the LT1462CN8 stable with capacitive loads?
Yes. The LT1462CN8 is unity-gain stable with capacitive loads up to 10 nF, according to the Analog Devices product information. This specification allows sensor wiring or other load capacitance to be connected at the amplifier output without sacrificing nominal unity-gain stability. Very large capacitances may still require isolation or compensation appropriate to the circuit.
What output voltage can the LT1462CN8 produce?
With a 10 kΩ load, the LT1462CN8 output can swing to within 1.5 V of either supply rail. The Analog Devices LT1462 product information specifies this 1.5 V headroom under that load condition. Designers should include this limitation when setting signal ranges near the supply rails or operating at low supply voltages.
What can replace the LT1462CN8?
No complete, verified drop-in replacement for the LT1462CN8 is identified in the available cross-reference information. The LT1462CN8#PBF lead-free ordering code is the closest identified listing, but it is a packaging designation rather than a distinct engineering alternative. Confirm pinout, supply range, bias current, stability, and load performance before substituting any candidate.
Is LT1462CN8 suitable for battery-powered instrumentation?
The LT1462CN8 is suitable for many battery-powered instrumentation circuits because each amplifier draws no more than 45 µA. Its 1 pA typical input bias current also minimizes disturbance to high-impedance sensors. The operating-voltage range and input common-mode limits must be checked against the battery voltage before final circuit approval.
Where can I download the LT1462CN8 datasheet?
The official Analog Devices LT1462 product page is the appropriate starting point for LT1462 documentation and ordering information. It is available at https://www.analog.com/en/products/lt1462.html. Use the manufacturer's datasheet and pin-description tables for absolute maximum ratings, supply limits, electrical characteristics, and package details.
Where can I find the LT1462CN8 pinout?
The LT1462CN8 pinout is documented in the Analog Devices LT1462 family documentation on the official product page. The distributor listing identifies the target as an 8-pin PDIP JFET amplifier. Because individual pin assignments are not reproduced in the available listing text, use the manufacturer pin-description table when assigning PCB tracks and probing the device.
When should I choose the LT1462CN8 over a higher-current amplifier?
Choose the LT1462CN8 when picoampere-level input bias and a maximum supply current of 45 µA per amplifier are more important than wide bandwidth or heavy load capability. Its 10 nF unity-gain capacitive-load stability and dual-channel integration can simplify precision sensor circuits. A higher-current amplifier is preferable when driving lower-resistance loads or processing faster signals.
How does the LT1462CN8 compare with a CMOS-input operational amplifier?
The LT1462CN8 emphasizes a 1 pA typical input bias current, while many CMOS-input amplifiers can offer lower supply current and broader bandwidth. According to the Analog Devices product information, the LT1462 also provides unity-gain stability up to 10 nF and 1.5 V output headroom with a 10 kΩ load. The proper choice depends on source impedance, speed, noise, and power requirements.
What is the best Analog Devices equivalent for LT1462CN8?
The closest identified Analog Devices ordering variant is LT1462CN8#PBF, which uses the lead-free marking convention and is listed as an 8-pin PDIP dual J-FET amplifier. It represents the same base LT1462 device family rather than a different competitor amplifier. Final equivalence must be confirmed against the manufacturer datasheet for the exact ordering code.
What is the price of LT1462CN8?
Current commercial pricing for the LT1462CN8 should be requested through the Request a Quote form on this page. The available LCSC result advertises a starting price for the LT1462CN8#PBF lead-free variant, but it does not provide qualifying quantity-break pricing for the exact target MPN. The request form also supports confirmation of stock, packaging, and lead time.
Is LT1462CN8 in stock and what is its lead time?
Stock and lead time should be confirmed through the Request a Quote form on this page. The LT1462CN8 appears in current distributor and marketplace listings, but those listings do not establish a guaranteed allocation for the exact non-#PBF ordering code. Include the required quantity, package, and target date in the request.
Can LT1462CN8 be used for photodiode or sensor amplification?
Yes. The LT1462CN8's 1 pA typical input bias current makes it well suited to photodiode, capacitive-sensor, and other high-impedance sources that can be disturbed by amplifier input current. Its dual configuration supports common two-channel measurement arrangements. Add the required transimpedance feedback components and verify bandwidth, noise, and common-mode limits in the final design.
Is the LT1462CN8 RoHS and REACH compliant?
The RoHS and REACH status of the exact LT1462CN8 ordering code is not established in the available product information. The related LT1462CN8#PBF listing uses a lead-free ordering designation, but that marking alone does not establish every regional compliance declaration. Request the current manufacturer declaration or material-compliance report before treating the part as qualified for a regulated assembly.

के लिए इंजीनियरिंग संदर्भ डेटा LT1462CN8 — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose the LT1462CN8 when your design needs two low-power, high-impedance amplifier channels and its 1 pA typical input bias current materially reduces measurement error. It is especially appropriate for photodiode, capacitive-sensor, low-level analog-filter, and battery-powered instrumentation circuits where the 45 µA maximum supply current per amplifier is valuable. Its unity-gain stability up to 10 nF can also simplify connection to moderately capacitive sources. Choose a higher-bandwidth amplifier when signal frequency requires more gain-bandwidth product or slew rate, and choose a CMOS-input device when its lower input capacitance and power consumption are more important than JFET-level picoampere bias current. No verified drop-in replacement was identified, so any alternative must be checked for package, pinout, common-mode range, output headroom, bias current, and load stability.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद
Brand Analog Devices
Package 8-pin PDIP
Number of Amplifiers 2
Input Stage JFET
Maximum Supply Current per Amplifier 45 µA
Typical Input Bias Current 1 pA
Unity-Gain Capacitive Load 10 nF
Output Swing at 10 kΩ Load Within 1.5 V of either supply

मुख्य विशेषताएँ

  • Very low input bias for precision high-impedance measurement (बनामTypical CMOS-input precision amplifier)
  • Low supply current without abandoning capacitive-load stability (बनामHigher-bandwidth dual amplifier)
  • Useful rail-relative output capability under a defined load (बनामLower-drive micropower amplifier)

डिज़ाइन नोट्स

Place the supply bypass capacitor as close as practical to the device supply pins, and route sensitive input and feedback traces away from switching nodes and high-current return paths. The JFET input stage has low typical bias current, but PCB contamination, flux residue, and moisture can still create leakage paths that are significant relative to picoampere-scale sensor currents.

Budget the worst-case supply demand as up to 45 µA per amplifier and add the quiescent current required by the rest of the analog chain. At low supply voltages, verify that the desired output span remains above the 1.5 V headroom specified for a 10 kΩ load. This is especially important when using battery operation or driving an ADC near either supply rail.

Do not treat unity-gain stability up to 10 nF as permission for arbitrary compensation values. Sensor and cable capacitance can combine with amplifier output impedance and feedback-network impedance to alter stability, phase margin, and settling behavior. Evaluate the complete source and load network, and add an isolation resistor when the connected capacitance is close to or greater than the 10 nF limit.

For high-impedance sources, minimize leakage from connectors, relays, PCB coatings, and nearby moisture. Keep input-node area small and avoid long exposed traces. Because the specified 1 pA input bias current is typical, engineering margin for leakage and temperature-dependent behavior is necessary when the measured source current approaches picoampere levels.

अनुपालन जानकारी

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

The LT1462CN8#PBF ordering code uses a lead-free marking designation, but the available product information does not establish the complete compliance status of the exact LT1462CN8 ordering code.

डेटा सत्यापन तिथि: 2026-11-14 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

LT1462CN8 datasheet LT1462CN8 pinout LT1462CN8 datasheet pdf LT1462CN8 equivalent LT1462CN8 replacement LT1462CN8 cross reference LT1462CN8 price LT1462CN8 stock Analog Devices LT1462CN8 LT1462CN8 8-PDIP LT1462CN8 photodiode amplifier LT1462CN8 1pA input bias

संबंधित कंपोनेंट्स और शब्द

Analog Devices LT1462CN8 LT1462CN8#PBF LT1462 LT1463 Dual operational amplifier JFET-input operational amplifier Amplifier IC Analog Devices Precision signal conditioning Picoampere input bias current Micropower operational amplifier Unity-gain stability Capacitive load Output headroom 8-pin PDIP DIP package Through-hole package Photodiode amplification Capacitive sensor interface Battery-powered instrumentation Active filter RoHS REACH
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें