LT1462CN8 - Dual Micropower JFET Op Amp | Analog Devices
料号: LT1462CN8 ✓ 量产中LT1462CN8 概述
An operational amplifier is a voltage-gain building block used to amplify small signals, buffer sensors, perform active filtering, and implement analog control functions. A JFET-input operational amplifier uses junction field-effect transistors at its input stage, providing very low input bias current. Within the broader hierarchy, the LT1462CN8 is an amplifier IC, specifically a precision-grade dual JFET operational amplifier designed for low-power analog signal conditioning.
The LT1462 family's defining characteristic is its combination of low power and very high input impedance. Each amplifier draws no more than 45 µA of supply current, while its typical input bias current is only 1 pA. These characteristics are useful when measuring signals from high-impedance sources because the amplifier contributes minimal loading to the source. The dual configuration also permits two independent amplifier channels in one package.
According to the Analog Devices product information, the LT1462 is unity-gain stable for capacitive loads up to 10 nF. This allows direct placement of up to 10 nF at the output without adding a separate isolation resistor in many applications. The output can also drive a 10 kΩ load to within 1.5 V of either supply rail, making the amplifier suitable for low-voltage instrumentation where output headroom matters.
Typical uses include precision sensor interfaces, low-level signal conditioning, photodiode amplifiers, capacitive transducers, battery-powered measurement systems, and analog filters. Because the device combines two channels, it can also implement differential, instrumentation, or active-filter topologies when a suitable resistor network and common-mode range are acceptable.
When designing around the LT1462CN8, account for the 1.5 V output headroom at a 10 kΩ load and verify the signal's common-mode range at the chosen supply voltage. Decoupling capacitors should be placed close to the supply pins, and sensitive input traces should be kept short and away from switching nodes to minimize leakage and pickup.
This page combines the manufacturer's published performance highlights with package details, application guidance, and a structured engineering comparison. It is intended to help designers evaluate the LT1462CN8 for low-power, high-impedance analog designs while recognizing that final circuit performance depends on supply voltage, load, source impedance, stability, and output-headroom requirements.
直接替换替代料: LT1462CN8 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
该产品暂无直接替换替代料。
请求替代料LT1462CN8 最大额定值与电气特性
| Amplifier Type | Dual JFET-input operational amplifier |
| Number of Channels | 2 channels |
| Number of Amplifiers | 2 amplifiers |
| Input Stage | JFET |
| Maximum Supply Current per Amplifier | 45 µA |
| Typical Input Bias Current | 1 pA |
| Unity-Gain Stability Capacitive Load | 10 nF |
| Output Load Condition | 10 kΩ |
| Output Swing from Either Supply Rail | Within 1.5 V |
| 封装 | 8-pin PDIP |
| 安装类型 | Through-hole |
LT1462CN8 8-pin pdip 引脚配置指南
LT1462CN8(8-pin pdip 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: LT1462CN8.
请参阅 数据手册 以查看完整引脚配置。
典型应用
LT1462CN8 适用于 6 应用s: Precision Photodiode Amplification, High-Impedance Sensor Signal Conditioning, Battery-Powered Measurement, Low-Level Analog Filtering, Capacitive Transducer Readout, Industrial Low-Level Signal Acquisition.
Precision Photodiode Amplification
The LT1462CN8 is suitable for photodiode and other high-impedance transimpedance front ends because its typical input bias current is only 1 pA. A JFET input stage contributes minimal current to the source, reducing error in currents that may be much smaller than the amplifier's signal current. Both channels can support a two-amplifier instrumentation arrangement when required. The designer should still calculate the transimpedance feedback value, bandwidth, noise contribution, and compensation needed for the photodiode capacitance. Unity-gain stability up to 10 nF helps with limited load capacitance, while the 1.5 V output headroom at a 10 kΩ load defines how close to the rails the output can operate.
High-Impedance Sensor Signal Conditioning
The LT1462CN8 fits electrochemical, capacitive, and resistive sensors whose source impedance could be disturbed by amplifier input bias current. With a typical input bias current of 1 pA and a dual 8-pin PDIP package, it can provide two conditioned channels without using separate single amplifiers. Each channel draws no more than 45 µA, which is valuable in battery-operated measurement systems. Input common-mode voltage, offset voltage, and noise must remain within the limits of the chosen supply configuration. The available 10 nF capacitive-load stability is useful when sensor wiring introduces capacitance, although long cables or highly capacitive transducers may require a dedicated isolation resistor.
Battery-Powered Measurement
The LT1462CN8 is a practical choice for portable measurement equipment where amplifier power can dominate the battery budget. Its maximum supply current of 45 µA per amplifier limits the current demand of each active channel, while the dual configuration can implement gain, filtering, or signal conversion stages in one package. At low supply voltages, however, output headroom must be planned carefully: the output reaches only within 1.5 V of either rail with a 10 kΩ load. Confirm that the sensor signal and required output span fit the available supply voltage, and include a practical power budget rather than relying only on the per-amplifier maximum current.
Low-Level Analog Filtering
The LT1462CN8 can serve as an active element in low-frequency analog filters built around high-impedance sources. Picoampere-level typical input bias reduces excitation-current error in sensitive filter stages, and unity-gain stability supports direct operation with capacitor networks up to 10 nF. The dual amplifier allows Sallen-Key, multiple-feedback, or related topologies without requiring two packages. Stability at the nominal unity-gain setting does not mean every feedback network is unconditionally stable, so resistor and capacitor values should be evaluated for the intended closed-loop gain. Output swing and common-mode limits must also be checked when the filter uses most of the available supply range.
Capacitive Transducer Readout
The LT1462CN8 is well matched to capacitive transducers because its 1 pA typical input bias produces very little input-current burden, while the amplifier remains unity-gain stable with capacitive loads up to 10 nF. These properties help preserve the integrity of charge-sensitive and frequency-based sensor signals. A practical design should still include input protection, defined grounding, and any required noise or drift compensation. The 8-pin PDIP package through-hole format can also suit prototype instrumentation and repair work where socketed DIP assembly is preferred. Confirm the complete electrical and pin details against the official LT1462 documentation before laying out the PCB.
Industrial Low-Level Signal Acquisition
The LT1462CN8 can serve in industrial signal-acquisition modules that combine sensor inputs with low-power analog processing. Its dual-channel configuration supports differential or sequential sensing, the JFET input stage limits source loading, and the 45 µA maximum supply current per amplifier supports compact low-power designs. Unity-gain stability for loads up to 10 nF is particularly helpful around cables, connector capacitance, and compact sensor interfaces. Industrial suitability depends on the exact operating-temperature grade, supply range, and compliance requirements rather than package format alone. Keep sensitive inputs away from switching nodes, use short traces, and place bypass capacitors close to the supply pins.
工程参考数据: LT1462CN8 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 |
|---|---|
| Brand | Analog Devices |
| Package | 8-pin PDIP |
| Number of Amplifiers | 2 |
| Input Stage | JFET |
| Maximum Supply Current per Amplifier | 45 µA |
| Typical Input Bias Current | 1 pA |
| Unity-Gain Capacitive Load | 10 nF |
| Output Swing at 10 kΩ Load | Within 1.5 V of either supply |
关键差异点
- Very low input bias for precision high-impedance measurement (对比 Typical CMOS-input precision amplifier)
- Low supply current without abandoning capacitive-load stability (对比 Higher-bandwidth dual amplifier)
- Useful rail-relative output capability under a defined load (对比 Lower-drive micropower amplifier)
设计说明
Place the supply bypass capacitor as close as practical to the device supply pins, and route sensitive input and feedback traces away from switching nodes and high-current return paths. The JFET input stage has low typical bias current, but PCB contamination, flux residue, and moisture can still create leakage paths that are significant relative to picoampere-scale sensor currents.
Budget the worst-case supply demand as up to 45 µA per amplifier and add the quiescent current required by the rest of the analog chain. At low supply voltages, verify that the desired output span remains above the 1.5 V headroom specified for a 10 kΩ load. This is especially important when using battery operation or driving an ADC near either supply rail.
Do not treat unity-gain stability up to 10 nF as permission for arbitrary compensation values. Sensor and cable capacitance can combine with amplifier output impedance and feedback-network impedance to alter stability, phase margin, and settling behavior. Evaluate the complete source and load network, and add an isolation resistor when the connected capacitance is close to or greater than the 10 nF limit.
For high-impedance sources, minimize leakage from connectors, relays, PCB coatings, and nearby moisture. Keep input-node area small and avoid long exposed traces. Because the specified 1 pA input bias current is typical, engineering margin for leakage and temperature-dependent behavior is necessary when the measured source current approaches picoampere levels.
合规信息
The LT1462CN8#PBF ordering code uses a lead-free marking designation, but the available product information does not establish the complete compliance status of the exact LT1462CN8 ordering code.