LT1491AIS - 44V Micropower Quad RRIO Op Amp | Analog Devices
MPN: LT1491AIS ✓ सक्रियLT1491AIS अवलोकन
An operational amplifier is a voltage-controlled differential amplifier used to amplify, buffer, filter, or compare analog signals. The LT1491A belongs to the micropower operational-amplifier hierarchy, combining rail-to-rail input and output stages, low quiescent current, and a wide supply range. “Rail-to-rail input and output” means the amplifier can accept input signals close to either supply rail and produce output swing toward both rails, improving signal range in low-voltage systems.
The LT1491A family provides four amplifiers in each package and accepts single or split supplies with a total voltage between 2V and 44V. Maximum input offset voltage is 500 µV, while the gain-bandwidth product is 200 kHz. Slew rate reaches 0.07 V/µs. Each amplifier draws no more than 40 µA of quiescent current, making the device suitable for portable measurement systems where four active amplifiers would otherwise create a substantial standby load.
The LT1491A is designed for precision-oriented, low-frequency signal conditioning rather than high-speed waveform work. Its 200 kHz gain-bandwidth product supports closed-loop bandwidths below the unity-gain frequency, depending on noise gain and stability requirements. The 500 µV maximum offset is particularly relevant to current-sense, bridge-sensor, and feedback applications where a small DC error can dominate the measurement at low full-scale values.
Typical uses include battery-powered sensor interfaces, portable test equipment, industrial control modules, low-level signal conditioning, and precision current measurement. Its 44V maximum total supply voltage also allows operation in higher-voltage industrial systems when appropriate protection is implemented. The four-channel configuration reduces package count when a system requires several similar low-power amplifier functions.
Designers should use the manufacturer pin-description table and operating-limit tables when assigning PCB tracks. Input and output pins must remain within their absolute maximum ratings, including during supply transitions and fault conditions. Decoupling capacitors should be placed close to the supply pins, and sensitive analog inputs should be kept away from switching nodes to reduce coupled noise.
This product page combines manufacturer specifications, verified ordering information, practical design guidance, and same-package replacement analysis. It is intended to help engineers determine whether the LT1491AIS fits a micropower, high-voltage signal-conditioning design without assuming that merely similar amplifier functions guarantee pin-to-pin compatibility.
के लिए ड्रॉप-इन विकल्प LT1491AIS — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
LT1491AHS#PBF
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
LT1491ACS#PBF
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
LT1491AHS
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
LT1491AIS Maximum Ratings और Electrical Characteristics
| Amplifier Type | Quad general-purpose operational amplifier |
| Number of Amplifiers | 4 channels |
| Supply Voltage Range | 2 V to 44 V total supply voltage |
| Supply Configuration | Single or split supply |
| Quiescent Current per Amplifier | 40 µA maximum |
| Input Offset Voltage | 500 µV maximum |
| Gain-Bandwidth Product | 200 kHz |
| Slew Rate | 0.07 V/µs |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Over-The-Top Operation | Supported |
| Reverse Supply Protection | Supported |
| पैकेज | 14-pin SO package |
| Package Family | SOIC family, surface-mount package |
LT1491AIS soic family, surface-mount package पिन कॉन्फ़िगरेशन गाइड
LT1491AIS (soic family, surface-mount package पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस एनालॉग कंपोनेंट में इनपुट, आउटपुट और पावर सप्लाई पिन हैं। ऑफ़सेट नल, कम्पनसेशन और एनेबल पिन कॉन्फ़िगरेशन के लिए निर्माता डेटाशीट देखें। सिग्नल कंडीशनिंग और एम्प्लीफ़ायर सर्किट के लिए आदर्श।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: LT1491AIS.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
LT1491AIS के लिए उपयुक्त है 6 अनुप्रयोगs: Battery-Powered Sensor Interfaces, Portable Test and Measurement, Industrial Current Sensing, Low-Power Data Acquisition, Precision Bridge and Resistance Measurement, Audio and Control Signal Buffers.
Battery-Powered Sensor Interfaces
The LT1491AIS fits low-power sensor conditioning because each of its four amplifiers draws no more than 40 µA of quiescent current while accepting single or split supplies from 2V to 44V total. Rail-to-rail inputs help preserve measurement range when sensor outputs approach the supply limits, and rail-to-rail outputs improve downstream utilization of low-voltage operating space. The 500 µV maximum input offset is relevant when conditioning low-level sensor signals, while the 200 kHz gain-bandwidth product is appropriate for filtering and instrumentation stages rather than high-speed waveform acquisition. Designers can use all four channels for buffering, gain, filtering, and threshold functions to reduce package count.
अनुशंसित
Portable Test and Measurement
Portable meters and field-test instruments benefit from the LT1491AIS because four precision-oriented channels are integrated into one 14-pin SO package. The 2V to 44V total supply range allows use with single low-voltage rails or split supplies, while the 500 µV maximum input offset helps preserve accuracy in low-level measurement paths. Its 200 kHz gain-bandwidth product supports measurement amplifiers, buffers, filters, and comparator functions, and the 40 µA per-amplifier quiescent current limits the impact on battery life. Rail-to-rail input and output operation also makes the device practical when the available input range and output swing must be used efficiently.
अनुशंसित
Industrial Current Sensing
The LT1491AIS can amplify small shunt-derived voltages in industrial current-measurement circuits when low offset and low standby power are priorities. The manufacturer specifies a maximum input offset voltage of 500 µV, which helps reduce output error in low-current measurements, and the rail-to-rail input stage can accept signals near the supply range. Four channels allow one amplifier to serve multiple sensing or conditioning functions. The 2V to 44V total supply capability accommodates suitable industrial rails, but designers must still protect inputs during switching events and confirm the exact suffix-specific operating limits. Its 200 kHz bandwidth is appropriate for typical current-loop and control signal paths.
अनुशंसित
Low-Power Data Acquisition
The LT1491AIS is suited to slow, low-power acquisition channels that require buffering or amplification rather than high-speed conversion. Its 200 kHz gain-bandwidth product supports common gain, filtering, and summing stages for sensors and transducers, while the 0.07 V/µs slew rate provides adequate dynamic performance for many low-bandwidth measurements. Four channels reduce both PCB area and the number of power rails and bypass networks. Rail-to-rail operation increases usable input and output range, and the 40 µA per-channel quiescent current is valuable in distributed or battery-powered acquisition systems. System designers should verify stability for each feedback topology and noise-gain configuration.
अनुशंसित
Precision Bridge and Resistance Measurement
The LT1491AIS can support bridge-based resistance and pressure measurements when offset error must remain small relative to the sensor output. Its 500 µV maximum input offset reduces DC error, while four rail-to-rail amplifiers can provide excitation buffering, channel amplification, difference amplification, and output conditioning. The broad 2V to 44V total supply range supports multiple laboratory and industrial system architectures. Micro-power operation is valuable when the bridge interface is remote or battery powered. Designers should calculate the maximum shunt or sensor excitation current, verify input common-mode limits under imbalance, and keep sensitive input routing away from digital and switching-current paths.
अनुशंसित
Audio and Control Signal Buffers
The LT1491AIS can buffer low-level audio and control signals when low quiescent current matters more than wideband performance. Rail-to-rail input and output stages provide useful range in single-supply systems, and the four-channel package can handle left and right audio paths, monitoring, or control channels in a compact design. The 200 kHz gain-bandwidth product and 0.07 V/µs slew rate are suitable for many low-frequency audio and feedback functions, although they do not target high-fidelity wideband audio performance. Designers should verify capacitive-load stability, output-current requirements, and ground-return paths. Low-power operation helps limit heat and unwanted channel-to-channel coupling from supply noise.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा LT1491AIS — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | LT1491AHS#PBF | LT1491ACS#PBF | LT1491AHS |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 14-pin SO package | 14-pin SO package | 14-pin SO package | 14-pin SO package |
| Number of Channels | 4 | 4 | 4 | 4 |
| Total Supply Voltage | 2 V to 44 V | 2 V to 44 V | 2 V to 44 V | 2 V to 44 V |
| Quiescent Current per Amplifier | 40 µA maximum | 40 µA maximum | 40 µA maximum | 40 µA maximum |
| Input Offset Voltage | 500 µV maximum | 500 µV maximum | 500 µV maximum | 500 µV maximum |
| Input and Output Operation | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
मुख्य विशेषताएँ
- Wide total supply range for micropower operation (बनामLT1491AHS#PBF)
- Four rail-to-rail amplifiers in one 14-pin SO package (बनामLT1491ACS#PBF)
- Bandwidth advantage over the H-suffix comparison listing (बनामLT1491AHS)
डिज़ाइन नोट्स
Place the supply bypass capacitor immediately between the positive supply and ground pins of the LT1491AIS, with the shortest and lowest-inductance connection possible. Keep sensitive input traces away from power switches, relay contacts, inductors, and high-current return paths. Because the amplifier has rail-to-rail inputs, exposed traces may collect more interference than inputs biased near a midpoint, so route each channel according to its sensitivity and use a quiet ground reference.
Do not treat the over-the-top capability as permission to exceed the absolute maximum input and output ratings. During shutdown, supply reversal, or a disconnected sensor, an input can move beyond the normal operating rails and damage the amplifier. Add series resistance or external clamping where the source can exceed the allowed range, and check the suffix-specific absolute maximum table before choosing operating limits.
Verify stable operation at the actual noise gain of every channel. The LT1491AIS is a micropower precision amplifier with 200 kHz gain-bandwidth product, so inverting stages, capacitive loads, and sensor capacitance can affect stability. Use the manufacturer feedback and compensation guidance, keep feedback paths compact, and avoid excessive loading on the output. Stable operation should be checked across supply, temperature, and process variation rather than only at nominal conditions.
Estimated: using the maximum 40 µA quiescent current per amplifier, all four channels consume up to 160 µA before input bias current, output-load current, and feedback-network losses are included. At a 5V supply, the quiescent contribution is approximately 0.8 mW. Actual board demand will be higher because sensor bias currents and external loads may dominate, so calculate the complete power budget before assigning battery capacity.
अनुपालन जानकारी
The LT1491AIS#PBF ordering code includes the lead-free finish designation. No explicit RoHS, REACH, halogen-free, conflict-minerals, or AEC-Q100 statement was identified.