Analog Devices

LTC1688IS - 100Mbps Quad RS-485/RS-422 Driver | Analog Devices

MPN: LTC1688IS ✓ सक्रिय
3 V to 5.5 V Vdss RS-485 and RS-422 Rds(on) 16-lead SOIC (IS suffix, industrial) Package
न्यूनतम ऑर्डर मात्रा: 1 |

LTC1688IS अवलोकन

The Analog Devices LTC1688IS is a quad differential bus/line driver IC that operates at data rates up to 100 Mbps while satisfying both RS-485 and RS-422 system requirements. It runs from a 3 V to 5.5 V supply, guarantees a propagation delay of 8 ns ±4 ns across the full operating temperature range, and tolerates the complete RS-485 common-mode range of -7 V to 12 V. All four driver outputs are Hot Swap capable, preserving backplane data integrity during live insertion and removal. The device is packaged in a 16-lead SOIC outline for industrial surface-mount designs.

A differential bus driver is a line-driver interface IC that converts a single-ended logic-level signal into a balanced two-wire differential pair. Differential signaling is the physical layer foundation of RS-485 and RS-422 field buses, where the receiver subtracts the two lines so that common-mode noise injected along the cable is rejected. In the product hierarchy, an LTC1688-class device sits at the interface-IC level: transceiver (driver + receiver) > line driver > differential bus interface > semiconductor.

Because the LTC1688 is a driver-only device, each of the four channels presents a low-power differential output stage that can source and sink current into a terminated cable. Key advantages include 100 Mbps maximum data rate, guaranteed 8 ns ±4 ns propagation delay, hot-swap output protection for backplane insertion, and operation across the -7 V to +12 V common-mode window required by RS-485 rather than the narrower RS-422 range. Per-channel driver enable inputs let a host isolate unused channels to reduce loading.

Architecturally, the LTC1688 is the complement of the LTC1689 quad receiver: the two share an identical 16-lead SOIC footprint and pin arrangement of VCC, GND, data input, enable and receiver-output positions, so a single board layout can host either a driver or a receiver in the same slot. Signal integrity is maintained because skew between the differential pair is minimized, keeping the common-mode rejection budget intact at 100 Mbps line rates.

Typical applications include industrial backplane and serial backplane architectures, instrumentation and data-acquisition racks, factory automation links, process-control equipment, and test and measurement systems that must add or remove cards without disrupting an active bus.

When designing around the LTC1688IS, keep the differential pair tightly coupled and matched, terminate the far end of the bus with the standard network termination, and confirm that the board layout keeps driver outputs away from logic that could be exposed during hot-swap events.

This page consolidates the manufacturer datasheet details, pin-level usage guidance, price and lead-time handling through the Request a Quote form, and a curated set of pin-compatible family alternatives into one engineering reference.

के लिए ड्रॉप-इन विकल्प LTC1688IS — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

LTC1688IS#PBF

✅ ड्रॉप-इन
📦 SOIC-16
Lead-free (RoHS-compliant) production ordering code of the identical 16-lead SOIC quad driver; same 100 Mbps rate, 8 ns ±4 ns delay and -7 V to +12 V common-mode range (0% parameter change)

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

LTC1689IS#PBF

✅ ड्रॉप-इन
📦 SOIC-16
Identical 16-lead SOIC pinout but a quad receiver instead of a quad driver; same 3 V to 5.5 V supply and RS-485/RS-422 compliance, function inverted rather than parameterized

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

LTC1689IS#TRPBF

✅ ड्रॉप-इन
📦 SOIC-16
Quad receiver in the same 16-lead SOIC footprint with tape-and-reel presentation; identical supply range and enable structure, complementary to the LTC1688 driver function

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

LTC1688IS#TRPBF

✅ ड्रॉप-इन
📦 SOIC-16
Tape-and-reel presentation of the same 16-lead SOIC quad driver; electrical set identical (100 Mbps, 8 ns ±4 ns, -7 V to +12 V), 0% parameter change

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

LTC1689IS

✅ ड्रॉप-इन
📦 SOIC-16
Industrial-grade quad receiver sharing the LTC1688 16-lead SOIC pin placement; same 3 V to 5.5 V rails, complementary receive rather than drive function

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

LTC1688IS विशेषताएं

Product Type Quad differential bus/line driver
Number of Drivers 4
Maximum Data Rate 100 Mbps
Propagation Delay 8 ns ±4 ns (guaranteed over full temperature range)
सप्लाई वोल्टेज 3 V to 5.5 V
Common-Mode Range -7 V to +12 V (RS-485)
Standards Supported RS-485 and RS-422
Hot Swap Yes, Hot Swap capable driver outputs
पैकेज 16-lead SOIC (IS suffix, industrial)
माउंटिंग प्रकार Surface Mount
Temperature Grade Industrial (IS suffix)
Enable Control Per-channel driver enable

LTC1688IS 16-lead soic (is suffix, industrial) पिन कॉन्फ़िगरेशन गाइड

LTC1688IS (16-lead soic (is suffix, industrial) पैकेज) के लिए पिन कॉन्फ़िगरेशन। पिन नंबरिंग, फ़ंक्शन और कनेक्शन आरेख निर्माता डेटाशीट में परिभाषित हैं। सटीक फुटप्रिंट और सोल्डरिंग दिशानिर्देशों के लिए इसे देखें।

LTC1688IS के लिए 16-lead soic (is suffix, industrial) पैकेज पिनआउट आरेख

इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: LTC1688IS.

देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।

सामान्य अनुप्रयोग

LTC1688IS के लिए उपयुक्त है 6 अनुप्रयोगs: Industrial Serial Backplane, Instrumentation and Data Acquisition, Factory Automation and Process Control, Telecom and Network Equipment Line Cards, Point-to-Point RS-422 Links, Security and Surveillance Camera Systems.

🏭

Industrial Serial Backplane

The LTC1688IS is a natural fit for industrial serial backplanes where cards are inserted and removed while other modules keep driving the bus. Its Hot Swap capable driver outputs maintain backplane data integrity during live card insertion, and the 100 Mbps maximum data rate with a guaranteed 8 ns ±4 ns propagation delay keeps bit timing margins stable as boards share a long multi-drop cable. The -7 V to +12 V common-mode tolerance absorbs ground-bounce offsets between cards that mount on different chassis grounds, which is the usual failure mode on hot-pluggable backplanes. Per-channel driver enable inputs let a system hold unused channels in a benign state so an idle card does not disturb the active differential pair.

⚡

Instrumentation and Data Acquisition

Test and measurement racks that gather sensor data over long shielded cables need a driver whose common-mode range tolerates ground potential differences between the rack and the remote fixture. The LTC1688IS operates across the full RS-485 common-mode range of -7 V to +12 V and also meets RS-422 requirements, so the same output stage works for a single long run to a remote instrument head or for a multi-drop sensor trunk. Because the device is a pure driver, the receive side can be handled by a separate receiver, keeping the transmit path's timing budget tight at 8 ns ±4 ns guaranteed propagation delay across temperature.

🏭

Factory Automation and Process Control

PLC-to-actuator and PLC-to-sensor links in a plant often run tens of metres across electrically noisy floors. The LTC1688IS drives the balanced pair with a 100 Mbps capability that leaves ample margin for 9600 baud to 10 Mbaud industrial protocols, while the differential topology rejects the coupled noise that single-ended signalling would convert into data errors. Its 3 V to 5.5 V supply range lets it sit alongside modern 3.3 V control logic and legacy 5 V line cards in the same rack without level translation on the driver side.

🌐

Telecom and Network Equipment Line Cards

Line cards and shelf managers in telecom and network equipment push status and control traffic across internal backplanes and short-reach cables at high speed. The LTC1688IS gives each card four independent differential channels at up to 100 Mbps with channel-to-channel delay held within a tight ±4 ns window, which keeps the differential pair balanced and preserves common-mode rejection. The 16-lead SOIC footprint is compact enough for high-density line card slot population, and the Hot Swap capable outputs let a card be replaced without taking the entire shelf offline.

🖥️

Point-to-Point RS-422 Links

Where a system uses the full RS-422 standard for dedicated point-to-point links rather than a multi-drop bus, the LTC1688IS still applies because the datasheet confirms the family also meets RS-422 requirements. This lets a designer standardise on one 16-lead SOIC driver part across both point-to-point and multi-drop sections of the same machine, simplifying bill of materials and stocking. With 100 Mbps of headroom, the same qualified driver can support high-speed data movement between motion controllers, drive electronics and vision systems.

🎥

Security and Surveillance Camera Systems

Camera and access-control installations run long cable runs between a head-end recorder and field devices, frequently across ground planes that differ by several volts. The LTC1688IS handles that with its -7 V to +12 V common-mode operating window while delivering the differential signalling needed to keep video-synchronisation and control traffic free of the hum and ground-loop artefacts typical of unbalanced links. The 100 Mbps ceiling gives headroom for future bandwidth growth on the same cabling, and the Hot Swap feature supports field replacement of a camera module without rebooting the whole installation.

What is the LTC1688IS?
The LTC1688IS is a quad differential bus/line driver IC from Analog Devices that converts logic-level inputs into balanced RS-485/RS-422 differential outputs. According to the LTC1688/LTC1689 datasheet, the part operates at data rates up to 100 Mbps, carries the full RS-485 common-mode range of -7 V to +12 V, and also meets RS-422 requirements. It is offered in a 16-lead SOIC package as the industrial (IS) grade version of the family.
What is the maximum data rate of the LTC1688IS?
The LTC1688IS supports data rates up to 100 Mbps. The manufacturer datasheet states that the LTC1688/LTC1689 are ultrahigh speed differential bus/line drivers able to operate at data rates up to 100 Mbps, with propagation delay guaranteed at 8 ns ±4 ns over the full operating temperature range. That combination of speed and bounded delay makes the device suitable for backplane and point-to-point links where bit timing margins must be held across temperature.
Is the LTC1688IS Hot Swap capable?
Yes, the LTC1688IS has Hot Swap capable driver outputs. The manufacturer product page for the LTC1688/LTC1689 family states that the driver outputs are Hot Swap capable, maintaining backplane data integrity during live card insertion and removal. Hot Swap behavior is critical in chassis-based systems where a module may be inserted or removed while other cards are actively driving the same bus.
What is the supply voltage range of the LTC1688IS?
The LTC1688IS operates from a 3 V to 5.5 V single supply. This matches the voltage range identified for the LTC1688/LTC1689 pin-compatible family, which operates between +3 V and +5.5 V supply rails. Because the device is a driver-only part, the supply rail mainly powers the output stage and logic input comparators, and the bus common-mode range extends well beyond the supply voltage.
Where can I download the LTC1688IS datasheet PDF?
The official datasheet PDF is published by Analog Devices at analog.com under the LTC1688/LTC1689 family document, and the same document covers both the LTC1688 and LTC1689. It contains the absolute maximum ratings, recommended operating conditions, propagation delay characteristics, the RS-485 and RS-422 compliance discussion, and the 16-lead SOIC pin configuration table. Request a Quote on this page if you need a controlled copy for your design file.
Where do I find the LTC1688IS pinout?
The LTC1688IS pinout is documented in the pin configuration table of the LTC1688/LTC1689 datasheet, published on the Analog Devices product page for the LTC1688. The part is a 16-lead SOIC device whose pins include VCC, GND, per-channel data inputs, per-channel driver enables and the receiver-output positions that mirror the LTC1689 receiver. Use the pin-description table in that datasheet when assigning PCB nets and verifying the exposed supply and ground connections.
What is the propagation delay of the LTC1688IS?
The LTC1688IS guarantees a propagation delay of 8 ns ±4 ns over the full operating temperature range. This is stated directly in the Analog Devices LTC1688/LTC1689 datasheet description and is the key timing figure for high-speed differential links. A bounded ±4 ns window keeps channel-to-channel skew small, which preserves the differential common-mode rejection needed at 100 Mbps line rates.
Does the LTC1688IS support RS-422 as well as RS-485?
Yes, the LTC1688IS satisfies both RS-422 and RS-485 requirements. The manufacturer datasheet states that these devices operate over the full RS-485 common mode range of -7 V to +12 V and also meet RS-422 requirements, so the same output stage can be used for point-to-point RS-422 links and for multi-drop RS-485 buses. This dual compliance is why the family is often specified for industrial interfaces that must cover both standards.
What is the difference between LTC1688IS and LTC1689IS?
The LTC1688IS is the quad driver half of the family and the LTC1689IS is the quad receiver half. Both use the identical 16-lead SOIC package with the same placement of VCC, GND, data input, enable and receiver-output pins, so no PCB changes are needed to swap them between slots. The LTC1688 pushes differential outputs onto the bus; the LTC1689 converts differential bus levels into logic-level receiver outputs.
What is the best drop-in replacement for the LTC1688IS?
The best verified drop-in options are the pin-compatible members of the same Analog Devices (formerly Linear Technology) family: the LTC1688IS#PBF lead-free production version, the LTC1688IS#TRPBF tape-and-reel variant, and the LTC1689IS parts, whose 16-lead SOIC pin arrangement is identical. No cross-manufacturer drop-in with verified pin-for-pin equivalence was identified, so for a guaranteed no-redesign swap choose a same-family part and confirm the enable polarity in the datasheet.
Is there a drop-in equivalent to the LTC1688IS from another manufacturer?
No cross-manufacturer drop-in equivalent with verified pin-for-pin compatibility was identified for the LTC1688IS. The documented pin-compatible alternatives come from the same LTC1688/LTC1689 family, whose identical 16-lead SOIC pinout makes substitution straightforward. If a second-source driver is mandatory, verify common-mode range, propagation delay tolerance and enable polarity against the manufacturer datasheet rather than relying on footprint similarity alone.
When should I choose the LTC1688IS over the LTC1689IS?
Choose the LTC1688IS when the board must transmit onto a differential bus, and the LTC1689IS when the board must receive from one. Both are 16-lead SOIC parts with identical pin placement and a 3 V to 5.5 V supply range, so a chassis slot can be designed to accept either. If a design needs full bidirectional capability, use a transceiver such as the MC3488AP1 rather than combining a separate driver and receiver.
Is the LTC1688IS suitable for industrial backplane and hot-swap systems?
Yes, the LTC1688IS is specifically suited to backplane architectures. Its driver outputs are Hot Swap capable, maintaining backplane data integrity when boards are inserted or removed while the bus is live, and the 100 Mbps rate with 8 ns ±4 ns guaranteed delay supports modern serial backplanes. The -7 V to +12 V common-mode window also tolerates the ground-bounce conditions typical of hot-pluggable multi-card chassis.
What can replace the LTC1688IS?
The LTC1688IS can be replaced by the pin-compatible LTC1688IS#PBF, which is the lead-free production ordering code of the same device, or by the LTC1688IS#TRPBF tape-and-reel ordering code for automated assembly. For a functionally complementary substitution, the LTC1689IS family shares the same 16-lead SOIC pinout but converts to receiver outputs instead of driving the bus. Always confirm enable polarity and supply range in the datasheet before substituting.
Is the LTC1688IS the same as LTC1688IS#PBF?
The LTC1688IS#PBF is the lead-free, production ordering code of the LTC1688IS family device and is the part most commonly listed for purchase. The #PBF suffix denotes the RoHS-compliant lead-free termination and lead-free solderable package, while IS denotes the industrial SOIC package and temperature grade. For assembly and quotation purposes, treat LTC1688IS#PBF as the specific orderable configuration of this 16-lead SOIC quad driver.
Where can I buy the LTC1688IS and what does it cost?
The LTC1688IS is stocked by multiple authorized distributors, but distributor pricing moves daily and varies with quantity and package form. XAIPART publishes current unit pricing and stock position for the exact ordering code on this page; use the Request a Quote form here to receive a firm quotation and lead-time confirmation for your volume. Requesting a quote for the LTC1688IS#PBF lead-free configuration keeps the quotation aligned with what actually ships.
What is the lead time for the LTC1688IS?
Lead time depends on the ordering configuration and current factory backlog, so it is best confirmed at the time of quotation. Use the Request a Quote form on this page to obtain current lead-time and stock information for the LTC1688IS, and specify whether you need the LTC1688IS#PBF tape-and-reel presentation for automated pick-and-place. For design scheduling, treat any lead time as order-specific rather than a fixed catalog value.
What are the key specifications of the LTC1688IS that engineers should know?
The key engineering figures are: 100 Mbps maximum data rate, guaranteed propagation delay of 8 ns ±4 ns over the full temperature range, RS-485 common-mode range of -7 V to +12 V, simultaneous RS-422 compliance, Hot Swap capable driver outputs, a 3 V to 5.5 V supply, and a 16-lead SOIC package. These are the values stated in the Analog Devices LTC1688/LTC1689 datasheet and product page and define where the device is and is not usable.

के लिए इंजीनियरिंग संदर्भ डेटा LTC1688IS — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose the LTC1688IS when the design must transmit onto an RS-485 or RS-422 differential bus and the system benefits from Hot Swap capable outputs, a 100 Mbps ceiling and a -7 V to +12 V common-mode window. Choose the LTC1689IS family when the card must receive from the bus; it shares the identical 16-lead SOIC pin placement, so the same PCB slot accepts either part. For bidirectional nodes, a transceiver such as the MC3488AP1 or VSC8502XML is a better fit than pairing a separate driver and receiver. For second sourcing, the LTC1688IS#PBF and LTC1688IS#TRPBF ordering codes give identical electrical behaviour with lead-free production and tape-and-reel assembly formats. No cross-manufacturer drop-in with verified pin-for-pin equivalence was confirmed, so any outside substitute must be checked against the datasheet for enable polarity, common-mode range and delay tolerance before release.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद LTC1688IS#PBF LTC1689IS#PBF LTC1689IS#TRPBF LTC1688IS#TRPBF LTC1689IS
Package SOIC-16 SOIC-16 - same SOIC-16 - same SOIC-16 - same SOIC-16 - same SOIC-16 - same
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Function Quad differential driver Quad differential driver Quad differential receiver Quad differential receiver Quad differential driver Quad differential receiver
Maximum Data Rate 100 Mbps 100 Mbps 100 Mbps 100 Mbps 100 Mbps 100 Mbps
Propagation Delay 8 ns ±4 ns guaranteed 8 ns ±4 ns guaranteed 8 ns ±4 ns guaranteed 8 ns ±4 ns guaranteed 8 ns ±4 ns guaranteed 8 ns ±4 ns guaranteed
Common-Mode Range -7 V to +12 V (RS-485) -7 V to +12 V (RS-485) -7 V to +12 V (RS-485) -7 V to +12 V (RS-485) -7 V to +12 V (RS-485) -7 V to +12 V (RS-485)
Standards RS-485 and RS-422 RS-485 and RS-422 RS-485 and RS-422 RS-485 and RS-422 RS-485 and RS-422 RS-485 and RS-422
Supply Voltage 3 V to 5.5 V 3 V to 5.5 V 3 V to 5.5 V 3 V to 5.5 V 3 V to 5.5 V 3 V to 5.5 V
Channel Count 4 drivers 4 drivers 4 receivers 4 receivers 4 drivers 4 receivers
Delivery Presentation Industrial SOIC tube ordering code Lead-free production code Lead-free production code Tape and reel Tape and reel Industrial ordering code

मुख्य विशेषताएँ

  • Hot Swap capable outputs for live backplane insertion (बनामLTC1689IS#PBF)
  • Guaranteed propagation delay window of 8 ns ±4 ns over full temperature (बनामLTC1688IS#TRPBF)
  • Full RS-485 common-mode range of -7 V to +12 V (बनामLTC1689IS)
  • Quad driver density in a 16-lead SOIC footprint (बनामLTC1688IS#PBF)

डिज़ाइन नोट्स

Route the differential pair as a tightly coupled, length-matched trace pair directly from the driver pins to the connector or backplane fingers. Mismatch between the two legs converts common-mode noise into differential error and directly degrades the common-mode rejection the LTC1688IS relies on across its -7 V to +12 V window. Keep the pair away from switching nodes and clock nets, and if the trace must cross a split plane, bridge the gap with a stitching capacitor and re-couple the pair with a ground reference.

Do not assume the LTC1688IS and the LTC1689IS are interchangeable in a live design even though the 16-lead SOIC pin placement is identical. One drives the bus and the other receives it, so swapping them without changing the board netlist leaves the system silent or drives an idle high-impedance node. Likewise, respect the per-channel enable polarity in the datasheet: tying an enable pin to the wrong rail can hold the driver output in an indeterminate state during hot-swap insertion.

Terminate the far end of the bus with the standard network termination appropriate for the topology, and keep stub lengths short so reflections from card edges do not combine with the 100 Mbps edge rate. For hot-pluggable backplanes, place the driver close to the connector so that the unterminated stub between driver and edge is electrically short. Confirm with an eye diagram or return-loss measurement on the assembled board rather than relying on simulation alone.

Decouple the supply pins with a short, low-inductance path to a local ground plane, placing the bulk capacitor near the device and a small ceramic capacitor adjacent to the pins. Although the bus common-mode range exceeds the supply rails, the output stage still needs a clean local supply, and supply bounce on a hot-plugged card shows up directly as bus noise. Estimated: with a 3.3 V supply and 5 mA of driver bias current, local supply ripple stays negligible compared with the differential signal swings, provided the loop area of the decoupling network is minimised.

अनुपालन जानकारी

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

Compliance statements are not published on the manufacturer product page for this family. The #PBF ordering suffix denotes the lead-free termination used by Analog Devices for RoHS-compliant production parts, but the formal RoHS, REACH and halogen-free declarations should be confirmed on the manufacturer product page before release. No AEC-Q100 qualification is stated for this industrial-grade interface device.

डेटा सत्यापन तिथि: 2026-11-09 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

ltc1688is pbf LTC1688IS datasheet LTC1688IS#PBF datasheet LTC1688IS pinout LTC1688IS equivalent LTC1688IS replacement LTC1688IS vs LTC1689IS LTC1688IS 100Mbps RS485 driver LTC1688IS hot swap backplane Analog Devices LTC1688IS LTC1688IS SOIC-16 footprint LTC1688IS price LTC1688IS stock LTC1688IS propagation delay 8ns

संबंधित कंपोनेंट्स और शब्द

Analog Devices LTC1688IS LTC1688IS#PBF LTC1688IS#TRPBF LTC1689IS RS-485 RS-422 differential bus driver line driver interface IC Hot Swap common-mode range propagation delay SOIC-16 100 Mbps backplane multi-drop bus balun-free differential signaling MC3488AP1 MC1489NG4 RoHS AEC-Q100
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें