LTC1688IS - 100Mbps Quad RS-485/RS-422 Driver | Analog Devices
MPN: LTC1688IS ✓ Hoạt độngLTC1688IS Tóm tắt
A differential bus driver is a line-driver interface IC that converts a single-ended logic-level signal into a balanced two-wire differential pair. Differential signaling is the physical layer foundation of RS-485 and RS-422 field buses, where the receiver subtracts the two lines so that common-mode noise injected along the cable is rejected. In the product hierarchy, an LTC1688-class device sits at the interface-IC level: transceiver (driver + receiver) > line driver > differential bus interface > semiconductor.
Because the LTC1688 is a driver-only device, each of the four channels presents a low-power differential output stage that can source and sink current into a terminated cable. Key advantages include 100 Mbps maximum data rate, guaranteed 8 ns ±4 ns propagation delay, hot-swap output protection for backplane insertion, and operation across the -7 V to +12 V common-mode window required by RS-485 rather than the narrower RS-422 range. Per-channel driver enable inputs let a host isolate unused channels to reduce loading.
Architecturally, the LTC1688 is the complement of the LTC1689 quad receiver: the two share an identical 16-lead SOIC footprint and pin arrangement of VCC, GND, data input, enable and receiver-output positions, so a single board layout can host either a driver or a receiver in the same slot. Signal integrity is maintained because skew between the differential pair is minimized, keeping the common-mode rejection budget intact at 100 Mbps line rates.
Typical applications include industrial backplane and serial backplane architectures, instrumentation and data-acquisition racks, factory automation links, process-control equipment, and test and measurement systems that must add or remove cards without disrupting an active bus.
When designing around the LTC1688IS, keep the differential pair tightly coupled and matched, terminate the far end of the bus with the standard network termination, and confirm that the board layout keeps driver outputs away from logic that could be exposed during hot-swap events.
This page consolidates the manufacturer datasheet details, pin-level usage guidance, price and lead-time handling through the Request a Quote form, and a curated set of pin-compatible family alternatives into one engineering reference.
Bộ thay thế dễ dàng lắp đặt cho LTC1688IS — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
LTC1688IS#PBF
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LTC1689IS#PBF
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LTC1689IS#TRPBF
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LTC1688IS#TRPBF
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LTC1689IS
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LTC1688IS Thông số kỹ thuật
| Product Type | Quad differential bus/line driver |
| Number of Drivers | 4 |
| Maximum Data Rate | 100 Mbps |
| Propagation Delay | 8 ns ±4 ns (guaranteed over full temperature range) |
| Điện áp cung cấp | 3 V to 5.5 V |
| Common-Mode Range | -7 V to +12 V (RS-485) |
| Standards Supported | RS-485 and RS-422 |
| Hot Swap | Yes, Hot Swap capable driver outputs |
| Hộp | 16-lead SOIC (IS suffix, industrial) |
| Kiểu lắp đặt | Surface Mount |
| Temperature Grade | Industrial (IS suffix) |
| Enable Control | Per-channel driver enable |
Hướng dẫn cấu hình chân LTC1688IS 16-lead soic (is suffix, industrial)
Cấu hình chân cho LTC1688IS (16-lead soic (is suffix, industrial) gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho LTC1688IS.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
LTC1688IS phù hợp cho 6 Áp dụngs: Industrial Serial Backplane, Instrumentation and Data Acquisition, Factory Automation and Process Control, Telecom and Network Equipment Line Cards, Point-to-Point RS-422 Links, Security and Surveillance Camera Systems.
Industrial Serial Backplane
The LTC1688IS is a natural fit for industrial serial backplanes where cards are inserted and removed while other modules keep driving the bus. Its Hot Swap capable driver outputs maintain backplane data integrity during live card insertion, and the 100 Mbps maximum data rate with a guaranteed 8 ns ±4 ns propagation delay keeps bit timing margins stable as boards share a long multi-drop cable. The -7 V to +12 V common-mode tolerance absorbs ground-bounce offsets between cards that mount on different chassis grounds, which is the usual failure mode on hot-pluggable backplanes. Per-channel driver enable inputs let a system hold unused channels in a benign state so an idle card does not disturb the active differential pair.
Được đề xuất
Instrumentation and Data Acquisition
Test and measurement racks that gather sensor data over long shielded cables need a driver whose common-mode range tolerates ground potential differences between the rack and the remote fixture. The LTC1688IS operates across the full RS-485 common-mode range of -7 V to +12 V and also meets RS-422 requirements, so the same output stage works for a single long run to a remote instrument head or for a multi-drop sensor trunk. Because the device is a pure driver, the receive side can be handled by a separate receiver, keeping the transmit path's timing budget tight at 8 ns ±4 ns guaranteed propagation delay across temperature.
Được đề xuất
Factory Automation and Process Control
PLC-to-actuator and PLC-to-sensor links in a plant often run tens of metres across electrically noisy floors. The LTC1688IS drives the balanced pair with a 100 Mbps capability that leaves ample margin for 9600 baud to 10 Mbaud industrial protocols, while the differential topology rejects the coupled noise that single-ended signalling would convert into data errors. Its 3 V to 5.5 V supply range lets it sit alongside modern 3.3 V control logic and legacy 5 V line cards in the same rack without level translation on the driver side.
Được đề xuất
Telecom and Network Equipment Line Cards
Line cards and shelf managers in telecom and network equipment push status and control traffic across internal backplanes and short-reach cables at high speed. The LTC1688IS gives each card four independent differential channels at up to 100 Mbps with channel-to-channel delay held within a tight ±4 ns window, which keeps the differential pair balanced and preserves common-mode rejection. The 16-lead SOIC footprint is compact enough for high-density line card slot population, and the Hot Swap capable outputs let a card be replaced without taking the entire shelf offline.
Được đề xuất
Point-to-Point RS-422 Links
Where a system uses the full RS-422 standard for dedicated point-to-point links rather than a multi-drop bus, the LTC1688IS still applies because the datasheet confirms the family also meets RS-422 requirements. This lets a designer standardise on one 16-lead SOIC driver part across both point-to-point and multi-drop sections of the same machine, simplifying bill of materials and stocking. With 100 Mbps of headroom, the same qualified driver can support high-speed data movement between motion controllers, drive electronics and vision systems.
Được đề xuất
Security and Surveillance Camera Systems
Camera and access-control installations run long cable runs between a head-end recorder and field devices, frequently across ground planes that differ by several volts. The LTC1688IS handles that with its -7 V to +12 V common-mode operating window while delivering the differential signalling needed to keep video-synchronisation and control traffic free of the hum and ground-loop artefacts typical of unbalanced links. The 100 Mbps ceiling gives headroom for future bandwidth growth on the same cabling, and the Hot Swap feature supports field replacement of a camera module without rebooting the whole installation.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LTC1688IS — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LTC1688IS#PBF | LTC1689IS#PBF | LTC1689IS#TRPBF | LTC1688IS#TRPBF | LTC1689IS |
|---|---|---|---|---|---|---|
| Package | SOIC-16 | SOIC-16 - same | SOIC-16 - same | SOIC-16 - same | SOIC-16 - same | SOIC-16 - same |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Function | Quad differential driver | Quad differential driver | Quad differential receiver | Quad differential receiver | Quad differential driver | Quad differential receiver |
| Maximum Data Rate | 100 Mbps | 100 Mbps | 100 Mbps | 100 Mbps | 100 Mbps | 100 Mbps |
| Propagation Delay | 8 ns ±4 ns guaranteed | 8 ns ±4 ns guaranteed | 8 ns ±4 ns guaranteed | 8 ns ±4 ns guaranteed | 8 ns ±4 ns guaranteed | 8 ns ±4 ns guaranteed |
| Common-Mode Range | -7 V to +12 V (RS-485) | -7 V to +12 V (RS-485) | -7 V to +12 V (RS-485) | -7 V to +12 V (RS-485) | -7 V to +12 V (RS-485) | -7 V to +12 V (RS-485) |
| Standards | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 |
| Supply Voltage | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V |
| Channel Count | 4 drivers | 4 drivers | 4 receivers | 4 receivers | 4 drivers | 4 receivers |
| Delivery Presentation | Industrial SOIC tube ordering code | Lead-free production code | Lead-free production code | Tape and reel | Tape and reel | Industrial ordering code |
Bảo phân biệt quan trọng
- Hot Swap capable outputs for live backplane insertion (vsLTC1689IS#PBF)
- Guaranteed propagation delay window of 8 ns ±4 ns over full temperature (vsLTC1688IS#TRPBF)
- Full RS-485 common-mode range of -7 V to +12 V (vsLTC1689IS)
- Quad driver density in a 16-lead SOIC footprint (vsLTC1688IS#PBF)
Ghi chú thiết kế
Route the differential pair as a tightly coupled, length-matched trace pair directly from the driver pins to the connector or backplane fingers. Mismatch between the two legs converts common-mode noise into differential error and directly degrades the common-mode rejection the LTC1688IS relies on across its -7 V to +12 V window. Keep the pair away from switching nodes and clock nets, and if the trace must cross a split plane, bridge the gap with a stitching capacitor and re-couple the pair with a ground reference.
Do not assume the LTC1688IS and the LTC1689IS are interchangeable in a live design even though the 16-lead SOIC pin placement is identical. One drives the bus and the other receives it, so swapping them without changing the board netlist leaves the system silent or drives an idle high-impedance node. Likewise, respect the per-channel enable polarity in the datasheet: tying an enable pin to the wrong rail can hold the driver output in an indeterminate state during hot-swap insertion.
Terminate the far end of the bus with the standard network termination appropriate for the topology, and keep stub lengths short so reflections from card edges do not combine with the 100 Mbps edge rate. For hot-pluggable backplanes, place the driver close to the connector so that the unterminated stub between driver and edge is electrically short. Confirm with an eye diagram or return-loss measurement on the assembled board rather than relying on simulation alone.
Decouple the supply pins with a short, low-inductance path to a local ground plane, placing the bulk capacitor near the device and a small ceramic capacitor adjacent to the pins. Although the bus common-mode range exceeds the supply rails, the output stage still needs a clean local supply, and supply bounce on a hot-plugged card shows up directly as bus noise. Estimated: with a 3.3 V supply and 5 mA of driver bias current, local supply ripple stays negligible compared with the differential signal swings, provided the loop area of the decoupling network is minimised.
Thông tin tuân thủ
Compliance statements are not published on the manufacturer product page for this family. The #PBF ordering suffix denotes the lead-free termination used by Analog Devices for RoHS-compliant production parts, but the formal RoHS, REACH and halogen-free declarations should be confirmed on the manufacturer product page before release. No AEC-Q100 qualification is stated for this industrial-grade interface device.