MC1458IDT - Dual 1 MHz Op Amp | STMicroelectronics
MPN: MC1458IDT ✓ सक्रियMC1458IDT अवलोकन
An operational amplifier is an analog building block used to amplify voltage differences and implement feedback-based functions such as voltage followers, summing amplifiers, integrators, comparators, and active filters. The MC1458 belongs to the dual general-purpose operational-amplifier family, combining two independent amplifiers in one package. This integration reduces board area in analog systems that need more than one amplifier but do not require rail-to-rail inputs or low-noise instrumentation performance.
The device's 1 MHz gain-bandwidth product makes it suitable for moderate-speed feedback networks and audio-frequency signal conditioning. Its 0.8 V/µs slew rate limits how quickly the output can follow large voltage changes, so stable feedback compensation and suitable loop-gain choices remain important. The 30 nA input bias current is particularly useful when driving relatively high-impedance sensors or resistive networks, because input loading has less effect on the source signal.
Each amplifier in the MC1458 can operate from a wide range of supply voltages, enabling operation in both conventional single-supply and dual-supply analog systems. STMicroelectronics describes the MC1458 as a monolithic dual operational amplifier intended for integrators, summing amplifiers, and general feedback applications. Short-circuit protection and an absence of latch-up behavior support dependable use in conventional amplifier topologies.
Typical applications include audio preamplification, low-frequency active filtering, instrumentation signal conditioning, voltage buffering, summing and difference amplifiers, and general feedback control. In a voltage follower, the high input impedance limits source loading. In an integrator or active filter, component tolerances and amplifier bandwidth determine usable frequency range. The SOIC-8 package is suitable for conventional surface-mount assembly and exists in tape-and-reel distribution format.
When designing around the MC1458IDT, preserve signal headroom at the amplifier output and keep feedback-loop bandwidth compatible with the 1 MHz gain-bandwidth product. Place input, output, and compensation components close to their associated pins, and avoid long high-impedance traces that can increase noise pickup. Decoupling capacitors should connect directly across the supply pins to minimize supply-to-ground loop area.
This product page combines the STMicroelectronics family description with a practical breakdown of the MC1458IDT's amplifier count, bandwidth, slew rate, bias current, package, and application roles. It also provides replacement guidance, pin-location information, comparison criteria, and design notes for engineers evaluating the MC1458 against other general-purpose dual operational amplifiers.
के लिए ड्रॉप-इन विकल्प MC1458IDT — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस सीरीज़ के वेरिएंट
समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं MC1458IDT (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Package, Device Type, Short-Circuit Protection.
MC1458DT
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापितकीमत के लिए संपर्क करें
डेटाशीट देखें →MC1458CDT
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित📋 संदर्भ विकल्प (कैटलॉग में नहीं)
MC1458IDT Maximum Ratings और Electrical Characteristics
| Product Type | Dual operational amplifier |
| Number of Amplifier Circuits | 2 circuits |
| Amplifier Type | General-purpose |
| Gain-Bandwidth Product | 1 MHz |
| Slew Rate | 0.8 V/µs |
| Input Bias Current | 30 nA |
| Short-Circuit Protection | Supported |
| पैकेज | 8-pin SOIC |
| माउंटिंग प्रकार | Surface mount |
| Packaging Format | Cut Tape and Digi-Reel |
| Product Status | Active |
MC1458IDT 8-pin soic पिन कॉन्फ़िगरेशन गाइड
MC1458IDT (8-pin soic पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस एनालॉग कंपोनेंट में इनपुट, आउटपुट और पावर सप्लाई पिन हैं। ऑफ़सेट नल, कम्पनसेशन और एनेबल पिन कॉन्फ़िगरेशन के लिए निर्माता डेटाशीट देखें। सिग्नल कंडीशनिंग और एम्प्लीफ़ायर सर्किट के लिए आदर्श।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: MC1458IDT.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
MC1458IDT के लिए उपयुक्त है 6 अनुप्रयोगs: Audio Signal Buffering, Active Low-Frequency Filtering, Summing and Mixing Amplifier, Integrator and Control-Loop Circuit, Instrumentation Signal Conditioning, General Feedback Control.
Audio Signal Buffering
The MC1458IDT fits audio-frequency voltage buffering because its 1 MHz gain-bandwidth product provides more bandwidth than typical baseband audio signal paths, while the 0.8 V/µs slew rate supports moderate-amplitude waveforms. Its 30 nA input bias current also limits loading when the source is a high-impedance audio front end. Each half of the IC can implement a unity-gain buffer, impedance converter, or non-inverting stage. Because the output is not rail-to-rail by default, check the output swing against the signal peak and load. Keep feedback resistors close to the relevant pins and use short input routes to reduce susceptibility to noise.
अनुशंसित
Active Low-Frequency Filtering
The MC1458IDT is suitable for first- and second-order active filters operating below its 1 MHz gain-bandwidth limit. The amplifier's 30 nA input bias current is advantageous with high-impedance resistor networks because it reduces the voltage shift caused by input loading, while its 0.8 V/µs slew rate helps preserve waveform shape at low frequencies. Component tolerances and the op amp's finite gain can shift the filter's center frequency and Q. Validate the selected R and C values across temperature and load, and keep the feedback network physically compact to reduce parasitic effects. The wide operating-voltage range also supports conventional dual-supply filter designs.
अनुशंसित
Summing and Mixing Amplifier
The MC1458IDT can implement weighted summing, mixing, and difference functions where two independent amplifier channels are useful in one 8-pin SOIC package. Its 1 MHz gain-bandwidth product supports moderate-bandwidth closed-loop gains, while the 30 nA input bias current reduces errors in high-impedance summing networks. The principal design limit is the 0.8 V/µs slew rate when combining several full-scale signals. Calculate the worst-case summed output amplitude and verify that it remains within the amplifier's output-swing limits. Accurate resistor ratios and short, quiet routing are essential for preserving the intended weighted sum.
अनुशंसित
Integrator and Control-Loop Circuit
The MC1458IDT is explicitly suited to integrator and general feedback applications, allowing its two amplifier channels to implement an integration stage and an auxiliary control or monitoring function. Its 1 MHz gain-bandwidth product is adequate for low-frequency loops, and the 0.8 V/µs slew rate defines the usable large-signal bandwidth. Practical integrator designs require attention to capacitor leakage, input bias current, resistor tolerance, and saturation recovery. Limit the working frequency well below the amplifier's unity-gain bandwidth and include a suitable feedback resistor to control DC drift. Confirm the exact common-mode and output-swing limits before finalizing the loop operating range.
अनुशंसित
Instrumentation Signal Conditioning
The MC1458IDT can provide input buffering, gain, offset, and general analog conditioning for moderate-impedance sensors and low-frequency measurement channels. Its 30 nA input bias current reduces source-loading error compared with parts having substantially higher bias currents, and its 1 MHz gain-bandwidth product supports signal paths that do not require high-speed instrumentation amplifiers. A single package can serve two channels or combine buffering with gain. Check input offset voltage, common-mode range, output swing, and noise against the measurement accuracy requirement. For bridge sensors, low-offset or dedicated instrumentation amplifiers may be preferable when precision and common-mode performance dominate.
अनुशंसित
General Feedback Control
The MC1458IDT is appropriate for basic analog feedback control, regulator error amplification, and feedback-conditioned analog blocks because STMicroelectronics identifies general feedback applications as a primary use. Its 1 MHz gain-bandwidth product permits modest loop bandwidth, while the 0.8 V/µs slew rate affects transient response and large-signal stability. Use one channel as the forward-path amplifier and the other as a buffer, monitor, or auxiliary feedback path. Confirm phase margin through practical compensation testing, account for output loading, and keep the feedback node compact. This is a general-purpose solution rather than a dedicated precision regulator or instrumentation amplifier.
अनुशंसित
के लिए इंजीनियरिंग संदर्भ डेटा MC1458IDT — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | MC1458DT | MC1458CDT |
|---|---|---|---|
| Package | SOIC-8 | SOIC-8 | SOIC-8 |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Number of Amplifiers | 2 circuits | 2 circuits | 2 circuits |
| Gain-Bandwidth Product | 1 MHz | 1 MHz | 1 MHz |
| Slew Rate | 0.8 V/µs | 0.8 V/µs | 0.8 V/µs |
| Input Bias Current | 30 nA | 30 nA | 30 nA |
| Amplifier Type | General-purpose | General-purpose | General-purpose |
मुख्य विशेषताएँ
- Two general-purpose amplifiers in one compact package (बनामMC1458DT)
- Moderate bandwidth and slew performance for general analog feedback (बनामMC1458CDT)
- Low input loading for higher-impedance signal sources (बनामMC1458DT)
डिज़ाइन नोट्स
Place the input, output, feedback, and supply-decoupling connections directly to their corresponding SOIC-8 pins. Keep the ground return close to the amplifier and use a dedicated bypass capacitor from each supply pin to the local ground plane. The 1 MHz gain-bandwidth product makes the device appropriate for low-frequency and audio circuits, but long feedback traces can still create parasitic coupling or oscillation. Route sensitive inputs away from switching nodes and power inductors.
Do not assume that an 8-pin dual amplifier can replace every dual op amp with the same body size. Verify the exact pin assignments, supply-pin locations, input common-mode limits, output swing, and offset requirements. The MC1458IDT's 0.8 V/µs slew rate and 1 MHz gain-bandwidth product also constrain large-signal and high-frequency operation. Check the highest expected signal amplitude and closed-loop gain before finalizing the circuit.
For integrator and active-filter circuits, account for input bias current, capacitor leakage, and resistor tolerances rather than relying only on nominal component values. The 30 nA bias current can create meaningful DC error with very high source impedances. Keep resistor networks away from temperature-sensitive areas when possible, use low-leakage capacitors for integration, and validate stability over the intended frequency and load range with real prototype measurements.
Check the complete output-voltage range under the intended load because the allowable input and output common-mode range depends on the supply voltage. The MC1458 family supports a wide operating-voltage range, but that does not make every output waveform valid at every supply. Maintain the required output headroom for the selected feedback gain and load, and ensure the power-supply rails remain stable without excessive ripple.
अनुपालन जानकारी
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status is stated for the MC1458IDT. Confirm the current manufacturer product-page declarations or material documentation for the exact ordering code.