MC33202VD - Dual Rail-to-Rail Op Amp | onsemi | 8-SOIC
MPN: MC33202VD ✓ सक्रियMC33202VD अवलोकन
An operational amplifier, commonly called an op amp, is a high-gain analog building block used in amplifier, comparator, buffer, filtering, and feedback-control circuits. The MC33202 belongs to the operational-amplifier hierarchy, where rail-to-rail input and output capability broadens the usable signal range in low-voltage systems. Two amplifiers are integrated into each package, allowing compact designs with two independent analog channels.
The principal features are dual-channel construction, input common-mode operation beyond the supply rails, near-rail output swing, and operation from 1.8 V to 12 V. Input overdrive tolerance of 200 mV is particularly useful in sensor, filter, and feedback applications where signals may briefly approach or cross a rail. The 50 mV output-swing specification also allows a large portion of the available supply voltage to be used by downstream circuitry.
The MC33202 family is designed for very low supply voltages, making rail-to-rail behavior more relevant than the input and output ranges of conventional non-rail-to-rail amplifiers. The family provides rail-to-rail operation at both inputs and outputs. This architecture supports signal amplification when the input is close to either supply rail and improves output headroom when driving the next stage near the positive or negative limit.
Typical applications include low-voltage sensor interfaces, battery-powered analog measurement, audio signal conditioning, active filtering, instrumentation, and general-purpose dual-amplifier modules. Two channels can be used for instrumentation-amplifier input stages, active filters, differential signal conditioning, or separate gain and buffer functions when the circuit operates within the device's common-mode and output limits.
PCB design should prioritize short analog input paths, clean grounding, and stable supply bypassing. Place the input and output resistors close to their associated amplifier pins, route high-impedance sensor nodes away from switching nodes, and decouple the supply connection near the package. Because rail-to-rail input stages commonly use internal crossover transitions, input bias-current and offset behavior should be evaluated over the complete signal range rather than only near mid-supply.
This page combines the manufacturer family characteristics, package information, sourcing guidance, practical design considerations, and pin-compatible replacement options. It also identifies where channel-level electrical data should be confirmed in the manufacturer datasheet before a production design or PCB release.
के लिए ड्रॉप-इन विकल्प MC33202VD — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस सीरीज़ के वेरिएंट
समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं MC33202VD (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Package, Operating Temperature Range, Output Swing, RoHS Status, Supply Voltage Range.
MC33201D
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →MC33204D
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
TLV9302
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
TLV9102
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
TLV9352IDR
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →TLV9152IDBVR
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →MC33202VD Maximum Ratings और Electrical Characteristics
| Number of Amplifier Channels | 2 channels |
| Product Type | Dual operational amplifier |
| Supply Voltage Range | 1.8 V to 12 V |
| Input Common-Mode Operation | Rail-to-rail |
| Maximum Input Overdrive Without Output Phase Reversal | 200 mV beyond the supply rails |
| Output Swing | Within 50 mV of each supply rail |
| आउटपुट प्रकार | Rail-to-rail |
| Amplifier Classification | General-purpose amplifier |
| Package Type | 8-pin SOIC |
| माउंटिंग प्रकार | Surface mount |
| पिन की संख्या | 8 pins |
| Manufacturer Family | MC33201/MC33202/MC33204 family |
| Minimum Operating Supply Voltage | 1.8 V |
| Maximum Operating Supply Voltage | 12 V |
| ऑपरेटिंग तापमान रेंज | -55 °C to +125 °C |
| RoHS स्थिति | Unknown |
| REACH Status | Unknown |
| AEC-Q100 Qualification | Not applicable |
MC33202VD 8-pin soic पिन कॉन्फ़िगरेशन गाइड
MC33202VD (8-pin soic पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस एनालॉग कंपोनेंट में इनपुट, आउटपुट और पावर सप्लाई पिन हैं। ऑफ़सेट नल, कम्पनसेशन और एनेबल पिन कॉन्फ़िगरेशन के लिए निर्माता डेटाशीट देखें। सिग्नल कंडीशनिंग और एम्प्लीफ़ायर सर्किट के लिए आदर्श।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: MC33202VD.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
MC33202VD के लिए उपयुक्त है 6 अनुप्रयोगs: Battery-Powered Sensor Interfaces, Industrial Analog Measurement, Audio Signal Conditioning, Active Filtering, Portable Medical Monitoring, IoT and Edge Sensor Nodes.
Battery-Powered Sensor Interfaces
The MC33202VD fits low-energy sensor-conditioning circuits because each channel operates from a supply range beginning at 1.8 V. Rail-to-rail input operation is useful when a transducer produces signals near either supply rail, and the specified 200 mV input-overdrive tolerance allows brief excursions beyond the rails without phase reversal at the output. Two channels can form a gain stage followed by an active filter or buffer. Designers should verify input bias current, offset, noise, and the complete sensor output range before fixing the gain and feedback values.
अनुशंसित
Industrial Analog Measurement
The MC33202VD can condition low-level industrial signals when the measurement front end operates below 12 V and may swing close to its supply limits. Its rail-to-rail inputs maximize usable common-mode range, while the output can reach within 50 mV of each rail for downstream conversion or control circuitry. The dual package allows simultaneous amplification or filtering of two related channels, reducing component count. Use short, guarded sensor traces, maintain a stable ground reference, and confirm input bias-current error against the source impedance before selecting the external resistor network.
अनुशंसित
Audio Signal Conditioning
MC33202VD is suitable for line-level and low-voltage audio stages where the signal may approach the supply rails. Rail-to-rail inputs and outputs provide additional signal range in a compact dual-amplifier package, and the two channels can be configured as a filter, non-inverting amplifier, or buffer pair. The 50 mV output-swing figure defines the remaining headroom at either rail, which should be considered when driving the next stage. Feedback-component selection and decoupling layout remain essential for preserving low distortion and stable loop gain.
अनुशंसित
Active Filtering
The dual MC33202VD can implement two linked or independent active-filter sections within a 1.8 V to 12 V system. Rail-to-rail input behavior helps preserve filter response when signals occupy most of the available signal range, while near-rail output swing improves dynamic utilization. Common circuit arrangements include low-pass stages for sensor smoothing, band-pass sections for communication paths, and notch filters. Component tolerances should be balanced when high rejection is required, and the amplifier’s stability and output-current requirements should be checked against the selected capacitive load.
अनुशंसित
Portable Medical Monitoring
MC33202VD can support compact biomedical monitoring electronics when the signal chain operates from a low supply and uses two closely related analog channels. Its 1.8 V minimum supply and rail-to-rail input and output behavior suit battery-powered acquisition equipment, while the dual configuration can amplify and filter one input or process two sensor channels. Medical designs must independently evaluate noise, offset, patient protection, isolation, leakage, and regulatory requirements. The op-amp selection does not by itself establish compliance with medical-device standards.
अनुशंसित
IoT and Edge Sensor Nodes
MC33202VD is well suited to compact IoT sensor nodes because two analog channels fit into an 8-pin SOIC and operate from a supply as low as 1.8 V. The rail-to-rail characteristics accommodate sensor signals and ADC inputs that occupy much of the available voltage range. A typical implementation places the amplifier before an ADC input, with one channel buffering a sensor and the other amplifying a reference or second input. Care should be taken to keep high-impedance routes away from radio and switching circuitry, and to confirm the ADC input range against the amplifier’s output swing.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा MC33202VD — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | MC33201D | MC33204D | TLV9302 | TLV9102 | TLV9352 | TLV9152 |
|---|---|---|---|---|---|---|---|
| Brand | onsemi | onsemi | onsemi | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Number of Amplifier Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Product Class | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | Operational amplifier | Operational amplifier | Operational amplifier | Operational amplifier |
मुख्य विशेषताएँ
- Specified overdrive behavior beyond the supply rails (बनामMC33201D)
- Dual rail-to-rail input and output operation (बनामMC33204D)
- Compact integration of two analog channels (बनामTLV9302)
- Near-rail output utilization at low supply voltages (बनामTLV9102)
डिज़ाइन नोट्स
Place input, feedback, and output resistors close to the MC33202VD pins to minimize parasitic capacitance and susceptibility to interference. High-impedance input nodes should be short, guarded, and isolated from switching traces. For sensor interfaces, use a grounded guard where practical and route the sensor return directly to the amplifier ground reference rather than sharing a noisy return path with digital circuitry.
Decouple the MC33202VD supply connection close to the package and follow the manufacturer’s recommended input and output capacitor network. Because the device supports operation down to 1.8 V, the supply source must remain within that range during startup and transient conditions. Keep analog and switching supplies physically separated, and verify that supply ripple and ground movement do not consume the usable output range.
Do not assume that rail-to-rail input operation removes the need to check the full input common-mode range. Rail-to-rail input stages can introduce input-bias-current transitions and crossover-related offset changes near the rails. Design the signal range with margin, account for source-impedance error, and verify both channels across the expected supply voltage and temperature range before production release.
When using MC33202VD with a replacement such as TLV9302 or TLV9102, preserve the original feedback topology initially and check stability with the same source and load impedances. Bandwidth, noise, offset, bias current, and output-current capability can affect gain error and phase margin even when the devices are pin-to-pin compatible. Increase output isolation only after confirming that added capacitance will not destabilize the selected amplifier.
अनुपालन जानकारी
No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement is present in the retrieved manufacturer and distributor records. AEC-Q100 is not applicable to this general-purpose dual operational amplifier.