MC33202VD - Dual Rail-to-Rail Op Amp | onsemi | 8-SOIC
MPN: MC33202VD ✓ Hoạt độngMC33202VD Tóm tắt
An operational amplifier, commonly called an op amp, is a high-gain analog building block used in amplifier, comparator, buffer, filtering, and feedback-control circuits. The MC33202 belongs to the operational-amplifier hierarchy, where rail-to-rail input and output capability broadens the usable signal range in low-voltage systems. Two amplifiers are integrated into each package, allowing compact designs with two independent analog channels.
The principal features are dual-channel construction, input common-mode operation beyond the supply rails, near-rail output swing, and operation from 1.8 V to 12 V. Input overdrive tolerance of 200 mV is particularly useful in sensor, filter, and feedback applications where signals may briefly approach or cross a rail. The 50 mV output-swing specification also allows a large portion of the available supply voltage to be used by downstream circuitry.
The MC33202 family is designed for very low supply voltages, making rail-to-rail behavior more relevant than the input and output ranges of conventional non-rail-to-rail amplifiers. The family provides rail-to-rail operation at both inputs and outputs. This architecture supports signal amplification when the input is close to either supply rail and improves output headroom when driving the next stage near the positive or negative limit.
Typical applications include low-voltage sensor interfaces, battery-powered analog measurement, audio signal conditioning, active filtering, instrumentation, and general-purpose dual-amplifier modules. Two channels can be used for instrumentation-amplifier input stages, active filters, differential signal conditioning, or separate gain and buffer functions when the circuit operates within the device's common-mode and output limits.
PCB design should prioritize short analog input paths, clean grounding, and stable supply bypassing. Place the input and output resistors close to their associated amplifier pins, route high-impedance sensor nodes away from switching nodes, and decouple the supply connection near the package. Because rail-to-rail input stages commonly use internal crossover transitions, input bias-current and offset behavior should be evaluated over the complete signal range rather than only near mid-supply.
This page combines the manufacturer family characteristics, package information, sourcing guidance, practical design considerations, and pin-compatible replacement options. It also identifies where channel-level electrical data should be confirmed in the manufacturer datasheet before a production design or PCB release.
Bộ thay thế dễ dàng lắp đặt cho MC33202VD — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MC33202VD (cùng hình factor và footprint) — khác nhau ở Package, Operating Temperature Range, Output Swing, RoHS Status, Supply Voltage Range.
MC33201D
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MC33204D
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TLV9302
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TLV9102
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TLV9352IDR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →TLV9152IDBVR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MC33202VD Tỷ lệ tối đa & tính chất điện
| Number of Amplifier Channels | 2 channels |
| Product Type | Dual operational amplifier |
| Supply Voltage Range | 1.8 V to 12 V |
| Input Common-Mode Operation | Rail-to-rail |
| Maximum Input Overdrive Without Output Phase Reversal | 200 mV beyond the supply rails |
| Output Swing | Within 50 mV of each supply rail |
| Kiểu đầu ra | Rail-to-rail |
| Amplifier Classification | General-purpose amplifier |
| Package Type | 8-pin SOIC |
| Kiểu lắp đặt | Surface mount |
| Số lượng chân | 8 pins |
| Manufacturer Family | MC33201/MC33202/MC33204 family |
| Minimum Operating Supply Voltage | 1.8 V |
| Maximum Operating Supply Voltage | 12 V |
| Khoảng nhiệt độ hoạt động | -55 °C to +125 °C |
| Trạng thái RoHS | Unknown |
| REACH Status | Unknown |
| AEC-Q100 Qualification | Not applicable |
Hướng dẫn cấu hình chân MC33202VD 8-pin soic
Cấu hình chân cho MC33202VD (8-pin soic gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho MC33202VD.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MC33202VD phù hợp cho 6 Áp dụngs: Battery-Powered Sensor Interfaces, Industrial Analog Measurement, Audio Signal Conditioning, Active Filtering, Portable Medical Monitoring, IoT and Edge Sensor Nodes.
Battery-Powered Sensor Interfaces
The MC33202VD fits low-energy sensor-conditioning circuits because each channel operates from a supply range beginning at 1.8 V. Rail-to-rail input operation is useful when a transducer produces signals near either supply rail, and the specified 200 mV input-overdrive tolerance allows brief excursions beyond the rails without phase reversal at the output. Two channels can form a gain stage followed by an active filter or buffer. Designers should verify input bias current, offset, noise, and the complete sensor output range before fixing the gain and feedback values.
Được đề xuất
Industrial Analog Measurement
The MC33202VD can condition low-level industrial signals when the measurement front end operates below 12 V and may swing close to its supply limits. Its rail-to-rail inputs maximize usable common-mode range, while the output can reach within 50 mV of each rail for downstream conversion or control circuitry. The dual package allows simultaneous amplification or filtering of two related channels, reducing component count. Use short, guarded sensor traces, maintain a stable ground reference, and confirm input bias-current error against the source impedance before selecting the external resistor network.
Được đề xuất
Audio Signal Conditioning
MC33202VD is suitable for line-level and low-voltage audio stages where the signal may approach the supply rails. Rail-to-rail inputs and outputs provide additional signal range in a compact dual-amplifier package, and the two channels can be configured as a filter, non-inverting amplifier, or buffer pair. The 50 mV output-swing figure defines the remaining headroom at either rail, which should be considered when driving the next stage. Feedback-component selection and decoupling layout remain essential for preserving low distortion and stable loop gain.
Được đề xuất
Active Filtering
The dual MC33202VD can implement two linked or independent active-filter sections within a 1.8 V to 12 V system. Rail-to-rail input behavior helps preserve filter response when signals occupy most of the available signal range, while near-rail output swing improves dynamic utilization. Common circuit arrangements include low-pass stages for sensor smoothing, band-pass sections for communication paths, and notch filters. Component tolerances should be balanced when high rejection is required, and the amplifier’s stability and output-current requirements should be checked against the selected capacitive load.
Được đề xuất
Portable Medical Monitoring
MC33202VD can support compact biomedical monitoring electronics when the signal chain operates from a low supply and uses two closely related analog channels. Its 1.8 V minimum supply and rail-to-rail input and output behavior suit battery-powered acquisition equipment, while the dual configuration can amplify and filter one input or process two sensor channels. Medical designs must independently evaluate noise, offset, patient protection, isolation, leakage, and regulatory requirements. The op-amp selection does not by itself establish compliance with medical-device standards.
Được đề xuất
IoT and Edge Sensor Nodes
MC33202VD is well suited to compact IoT sensor nodes because two analog channels fit into an 8-pin SOIC and operate from a supply as low as 1.8 V. The rail-to-rail characteristics accommodate sensor signals and ADC inputs that occupy much of the available voltage range. A typical implementation places the amplifier before an ADC input, with one channel buffering a sensor and the other amplifying a reference or second input. Care should be taken to keep high-impedance routes away from radio and switching circuitry, and to confirm the ADC input range against the amplifier’s output swing.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MC33202VD — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MC33201D | MC33204D | TLV9302 | TLV9102 | TLV9352 | TLV9152 |
|---|---|---|---|---|---|---|---|
| Brand | onsemi | onsemi | onsemi | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Number of Amplifier Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Product Class | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | Operational amplifier | Operational amplifier | Operational amplifier | Operational amplifier |
Bảo phân biệt quan trọng
- Specified overdrive behavior beyond the supply rails (vsMC33201D)
- Dual rail-to-rail input and output operation (vsMC33204D)
- Compact integration of two analog channels (vsTLV9302)
- Near-rail output utilization at low supply voltages (vsTLV9102)
Ghi chú thiết kế
Place input, feedback, and output resistors close to the MC33202VD pins to minimize parasitic capacitance and susceptibility to interference. High-impedance input nodes should be short, guarded, and isolated from switching traces. For sensor interfaces, use a grounded guard where practical and route the sensor return directly to the amplifier ground reference rather than sharing a noisy return path with digital circuitry.
Decouple the MC33202VD supply connection close to the package and follow the manufacturer’s recommended input and output capacitor network. Because the device supports operation down to 1.8 V, the supply source must remain within that range during startup and transient conditions. Keep analog and switching supplies physically separated, and verify that supply ripple and ground movement do not consume the usable output range.
Do not assume that rail-to-rail input operation removes the need to check the full input common-mode range. Rail-to-rail input stages can introduce input-bias-current transitions and crossover-related offset changes near the rails. Design the signal range with margin, account for source-impedance error, and verify both channels across the expected supply voltage and temperature range before production release.
When using MC33202VD with a replacement such as TLV9302 or TLV9102, preserve the original feedback topology initially and check stability with the same source and load impedances. Bandwidth, noise, offset, bias current, and output-current capability can affect gain error and phase margin even when the devices are pin-to-pin compatible. Increase output isolation only after confirming that added capacitance will not destabilize the selected amplifier.
Thông tin tuân thủ
No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement is present in the retrieved manufacturer and distributor records. AEC-Q100 is not applicable to this general-purpose dual operational amplifier.