MC34072PG - Dual 44V Op Amp with 13V/us | onsemi
MPN: MC34072PG ✓ सक्रियMC34072PG अवलोकन
An operational amplifier is an amplifier IC that uses high-gain differential feedback to control an output voltage. The MC34072 family belongs to the broader operational amplifier, analog IC, and semiconductor hierarchies. It can operate from split supplies or a single supply and is particularly suited to circuits requiring higher supply tolerance than typical low-voltage rail-to-rail amplifiers.
The 4.5 MHz gain-bandwidth product supports useful closed-loop bandwidth at practical gain settings, while the 13 V/us slew rate allows outputs to change quickly without requiring JFET inputs. The manufacturer lists a 5 mV input offset-voltage figure for the commercial-temperature MC34072PG, and its bipolar construction is suited to general-purpose analog signal conditioning.
The MC34072 series combines precision bipolar performance with relatively high operating-voltage capability and fast settling behavior. Each amplifier can serve as an inverting or non-inverting stage, and the two independent channels allow simultaneous processing of related signals. This architecture is useful when a board needs one amplifier for filtering and another for buffering or gain control.
Typical uses include industrial sensor interfaces, low-frequency active filters, audio preamplifier stages, transducer amplifiers, feedback-control loops, and general instrumentation powered from industrial supply rails. The 44 V maximum supply also makes the device relevant to legacy 24 V control systems, provided the selected operating voltage and dissipation remain within the device ratings.
Place bypass capacitors close to the supply pins and route feedback components away from input and output traces to reduce oscillation risk. Confirm output swing, input common-mode range, load current, and thermal dissipation for each amplifier channel. Dual packages require evaluation of channel-to-channel behavior, not only the aggregate device rating.
This product page combines the MC34072PG operating characteristics with engineering-focused pin, packaging, replacement, and design guidance. It supports faster selection by placing verified headline specifications beside the practical constraints that determine whether the dual amplifier can operate safely in a target circuit.
के लिए ड्रॉप-इन विकल्प MC34072PG — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस सीरीज़ के वेरिएंट
समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं MC34072PG (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Input Offset Voltage, Mounting Type, Package, Supply Voltage Range.
MC34072P
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित📋 संदर्भ विकल्प (कैटलॉग में नहीं)
MC34072VPG
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित📋 संदर्भ विकल्प (कैटलॉग में नहीं)
MC33072P
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित📋 संदर्भ विकल्प (कैटलॉग में नहीं)
MC33072PG
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →MC34072PG Maximum Ratings और Electrical Characteristics
| Product Type | Dual general-purpose operational amplifier |
| Number of Circuits | 2 circuits |
| आउटपुट प्रकार | Single-ended |
| Supply Voltage Range | 3 V to 44 V |
| Gain-Bandwidth Product | 4.5 MHz |
| Slew Rate | 13 V/us |
| Input Offset Voltage | 5 mV |
| Amplifier Technology | Quality bipolar fabrication without JFET input technology |
| Supply Configuration | Single supply or split supply operation |
| पैकेज | 8-PDIP, 0.300 in (7.62 mm) pitch |
| माउंटिंग प्रकार | Through-hole insertion |
| Packaging | Tube |
| Operating Temperature Grade | Commercial temperature grade |
MC34072PG पिन कॉन्फ़िगरेशन
| पिन 1 | OUTA — Amplifier A output |
| पिन 2 | IN A- — Inverting input for amplifier A |
| पिन 3 | IN A+ — Non-inverting input for amplifier A |
| पिन 4 | V- — Negative supply or ground connection |
| पिन 5 | IN B+ — Non-inverting input for amplifier B |
| पिन 6 | IN B- — Inverting input for amplifier B |
| पिन 7 | OUTB — Amplifier B output |
| पिन 8 | V+ — Positive supply connection |
सामान्य अनुप्रयोग
MC34072PG के लिए उपयुक्त है 6 अनुप्रयोगs: Industrial Sensor Signal Conditioning, 24 V Control-System Feedback Amplifier, Active Audio Preamplifier, Low-Frequency Active Filter, Transducer and Bridge-Signal Interface, General-Purpose Instrumentation Buffer.
Industrial Sensor Signal Conditioning
The MC34072PG suits industrial sensor-conditioning stages that need two amplifier channels and a supply range extending to 44 V. One channel can amplify a transducer signal while the other provides filtering or an active differential input. Its 4.5 MHz gain-bandwidth product gives useful closed-loop bandwidth at moderate gains, and the 13 V/us slew rate reduces large-signal distortion during rapid input changes. The wide supply tolerance is particularly useful on 24 V control equipment, provided transient protection keeps every pin within the absolute maximum limits.
अनुशंसित
24 V Control-System Feedback Amplifier
The MC34072PG can amplify error and feedback signals in a 24 V control loop without requiring a low-voltage dual amplifier. The listed 3 V to 44 V operating range provides headroom for industrial rails, while 4.5 MHz gain-bandwidth product supports bandwidth above slow regulator loops. A 13 V/us slew rate helps the output track rapidly changing error signals. Designers should still verify the actual input common-mode range, output swing, stability with the selected feedback network, and power dissipation at the highest expected control voltage.
अनुशंसित
Active Audio Preamplifier
The MC34072PG provides two independent bipolar amplifier channels for microphone preamplification, line-level gain, or active filtering in audio equipment. Its 13 V/us slew rate can improve large-signal behavior compared with slower general-purpose amplifiers, while the 4.5 MHz gain-bandwidth product provides bandwidth beyond the audio range. The 5 mV listed input offset is important in low-level gain stages. For high-fidelity use, evaluate noise, input bias current, channel matching, output drive into the selected load, and the required dual-supply arrangement.
अनुशंसित
Low-Frequency Active Filter
The MC34072PG can implement active filters where two amplifier channels are needed for a second-order section or separate filtering stages. A 4.5 MHz gain-bandwidth product supports many audio and control-band applications, and the 13 V/us slew rate helps preserve low distortion during rapid waveform changes. Stable implementation depends on the selected noise gain and feedback topology, so use the manufacturer’s recommended operating region and verify phase margin on the final component tolerances. Add input and output isolation where the next stage presents a capacitive load.
अनुशंसित
Transducer and Bridge-Signal Interface
The MC34072PG can serve as a general-purpose interface for resistive, strain-gauge, or other slow-changing transducer signals when the system operates from a higher-voltage rail. One channel may amplify the sensor output and the other may generate a reference or drive a complementary stage. The 4.5 MHz gain-bandwidth product supports signal bandwidth above many mechanical sensing systems, while 13 V/us slew rate handles step inputs. High-impedance sources may reveal input bias-current effects, so verify leakage, sensor loading, grounding, and shield placement.
अनुशंसित
General-Purpose Instrumentation Buffer
The MC34072PG can buffer two instrumentation signals, isolate a source from the following ADC, or implement gain blocks in laboratory and industrial instrumentation. Its 13 V/us slew rate preserves large-signal fidelity, and the 4.5 MHz gain-bandwidth product supports moderate-bandwidth signal paths. The dual bipolar topology is useful where two channels save board area, but channel matching and offset behavior should be considered at high gain. Confirm input bias current, common-mode limits, output loading, and stability before substituting it for a dedicated precision amplifier.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा MC34072PG — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | MC34072P | MC34072VPG | MC33072P | MC33072PG |
|---|---|---|---|---|---|
| Brand | onsemi | onsemi | onsemi | onsemi | onsemi |
| Package | 8-PDIP (0.300, 7.62 mm) | 8-PDIP (0.300, 7.62 mm) | 8-PDIP (0.300, 7.62 mm) | 8-PDIP (0.300, 7.62 mm) | 8-PDIP (0.300, 7.62 mm) |
| Number of Amplifiers | 2 | 2 | 2 | 2 | 2 |
| Output Type | Single-ended | Single-ended | Single-ended | Single-ended | Single-ended |
| Input Technology | Bipolar, without JFET input technology | Bipolar, without JFET input technology | Bipolar, without JFET input technology | Bipolar | Bipolar |
मुख्य विशेषताएँ
- Wide single-supply operating range (बनामMC33072P)
- High slew rate for a general-purpose bipolar dual amplifier (बनामMC34072P)
- Two independent channels in one through-hole package (बनामLM2904PWR)
- Compatibility with the broader MC34072 family (बनामMC33072PG)
डिज़ाइन नोट्स
Check both amplifier channels when calculating dissipation because the package contains two amplifiers. Estimated: for each channel, use Pchannel = (VS - VOUT) × IOUT, then add the quiescent contribution from both channels. Compare the total with the datasheet power limit and expected ambient temperature. A 24 V rail at several milliamperes of load can create meaningful heat in an 8-pin PDIP without substantial copper cooling.
Place the supply-bypass capacitor immediately between the V+ and V- pins or close to the package pins on the supply route. Keep each channel’s feedback resistors and compensation components close to their associated amplifier inputs. Maintain separation between the two channels if they process uncorrelated or high-level signals, and provide a solid ground return to reduce common-impedance coupling.
Do not treat the 44 V supply rating as permission to operate without transient protection. Inductive or industrial wiring can introduce spikes above the absolute maximum voltage. Use suitable surge suppression, verify the input common-mode range for single-supply operation, and confirm output swing at the actual load. Also verify whether the selected gain and capacitive loading remain inside the stable operating region shown in the manufacturer documentation.
Keep input and output copper paths physically separated, especially around inverting-input nodes, because those nodes are sensitive to leakage and capacitive coupling. Route the ground return directly to the supply capacitor rather than through the output or feedback section. Use a low-impedance ground plane where possible and minimize exposed trace length around the two amplifier channels.
अनुपालन जानकारी
The retrieved manufacturer and distributor pages do not state the requested compliance declarations. Obtain current onsemi material or product compliance documentation for the exact MC34072PG ordering code.