OPA131PJ - 4MHz FET Op Amp, 50pA, 750uA | Texas Instruments
MPN: OPA131PJ ✓ सक्रियOPA131PJ अवलोकन
A FET-input operational amplifier is an analog amplifier whose input stage uses field-effect transistors rather than bipolar input transistors. This architecture produces extremely low input bias current, making FET-input amplifiers part of the operational-amplifier hierarchy and particularly useful when measuring high-impedance sources, photodiode currents, or sensor outputs whose bias-current error must remain small. Unlike bipolar-input amplifiers, the OPA131PJ can interface with high-source-impedance nodes without loading them as heavily.
The OPA131PJ combines low offset voltage, wide bandwidth, and capacitive-load drive. Its maximum input offset voltage is 750 µV, its gain-bandwidth product is 4 MHz, and its slew rate is 10 V/µs. The ±18 V supply capability allows operation from split supplies commonly used in industrial and instrumentation systems. Power consumption of 750 µA also supports battery-powered or low-power analog designs when the circuit does not require a more power-hungry amplifier.
The OPA131 series provides single, dual, and quad configurations in industry-standard pinouts, enabling designers to standardize across different channel counts. The single OPA131 is suitable for isolated signal-conditioning channels, while dual and quad versions can implement complete analog front ends. Its 4 MHz bandwidth provides useful response for audio-frequency and general-purpose closed-loop gains while retaining useful low-bias-current behavior.
Typical uses include transimpedance amplification for optical and chemical sensors, precision current-to-voltage conversion, bridge-signal conditioning, low-leakage measurement interfaces, and buffering high-impedance transducers. The 50 pA maximum bias current is especially important when source resistance is high, while the 750 µV maximum offset voltage supports accurate low-level amplification.
When designing around the OPA131PJ, check the common-mode input range against the actual signal and supply voltages, and use the manufacturer pin-description table when assigning PCB connections. Decoupling capacitors should be placed close to the supply pins, and feedback components should be positioned to minimize parasitic capacitance. The principal trade-off is that 4 MHz bandwidth is modest compared with modern high-speed amplifiers, but it is appropriate for precision, low-power, general-purpose signal paths.
This page combines the manufacturer electrical characteristics, package and pin information, practical application guidance, and a conservative drop-in-replacement assessment. The replacement analysis distinguishes verified same-footprint options from parts that require a different package, helping engineers preserve PCB compatibility while reviewing changes in offset, bandwidth, bias current, and common-mode behavior.
के लिए ड्रॉप-इन विकल्प OPA131PJ — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस सीरीज़ के वेरिएंट
समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं OPA131PJ (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Gain-Bandwidth Product, Input Bias Current, Input Stage, Slew Rate.
OPA131P
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित📋 संदर्भ विकल्प (कैटलॉग में नहीं)
OPA134PA
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापितकीमत के लिए संपर्क करें
डेटाशीट देखें →OPA131PJ Maximum Ratings और Electrical Characteristics
| Amplifier Type | Single general-purpose operational amplifier |
| Input Bias Current | 50 pA maximum |
| Power Consumption | 750 µA |
| Gain-Bandwidth Product | 4 MHz |
| Input Offset Voltage | 750 µV maximum |
| Supply Voltage Range | ±18 V |
| Slew Rate | 10 V/µs |
| Input Stage | FET input |
| Number of Channels | 1 channel |
| पैकेज | 8-pin PDIP |
| Terminal Form | Through-hole |
| Number of Terminals | 8 terminals |
| Package Shape | Rectangular |
| माउंटिंग प्रकार | Through-hole |
| Capacitive Load Drive | Excellent |
| Series Configuration Options | Single, dual, and quad versions |
| RoHS स्थिति | Compliant |
| Lead-Free Status | Lead free |
OPA131PJ पिन कॉन्फ़िगरेशन
| पिन 1 | NC — Not connected |
| पिन 2 | IN- — Inverting input |
| पिन 3 | IN+ — Non-inverting input |
| पिन 4 | V- — Negative supply connection |
| पिन 5 | NC — Offset null connection |
| पिन 6 | OUT — Output |
| पिन 7 | V+ — Positive supply connection |
| पिन 8 | NC — Not connected |
सामान्य अनुप्रयोग
OPA131PJ के लिए उपयुक्त है 6 अनुप्रयोगs: Photodiode Transimpedance Amplification, Precision Current Measurement, High-Impedance Sensor Signal Conditioning, Industrial Bridge Signal Conditioning, Low-Power Audio Buffering, Laboratory Instrumentation Buffer.
Photodiode Transimpedance Amplification
The OPA131PJ fits photodiode front ends because its FET input has a 50 pA maximum bias current, reducing the DC error created when bias current flows through a high feedback resistance. A 4 MHz gain-bandwidth product allows useful closed-loop bandwidth, while the 10 V/µs slew rate handles moderate signal changes. The transimpedance feedback network must be designed for the photodiode capacitance, and the completed circuit should be checked for stability with realistic stray capacitance. A resistor and capacitor combination around the inverting input establishes transimpedance gain and bandwidth, while the non-inverting input is usually grounded directly. OPA131PJ is preferable when low input leakage is more important than the very high bandwidth available from dedicated high-speed transimpedance amplifiers.
अनुशंसित
Precision Current Measurement
OPA131PJ is appropriate for picoampere-to-micropere current detection because the 50 pA maximum input bias current limits the measurement floor created by the amplifier itself. A transimpedance stage converts input current into a voltage that can be sampled by an ADC or control system. Its 4 MHz bandwidth supports moderate-rate measurements, and its wide ±18 V supply capability allows convenient selection of positive and negative rails. Feedback resistance and leakage around the summing node remain critical because board contamination can easily exceed the amplifier's specified bias current. Guarding, clean PCB practices, and careful capacitor selection are necessary for repeatable picoampere-class measurements.
अनुशंसित
High-Impedance Sensor Signal Conditioning
The OPA131PJ is well matched to high-impedance sensors whose output current must not be significantly loaded. Its FET input draws only 50 pA maximum bias current, while the 750 µV maximum offset voltage supports accurate amplification of low-level sensor signals. The 4 MHz gain-bandwidth product is sufficient for many pressure, chemical, humidity, and optical sensors operating below audio or low-frequency control bandwidths. The signal amplitude must remain inside the amplifier's common-mode input range, and the output must remain inside the specified swing limits. Bias-point calculations should include sensor impedance, resistor leakage, and temperature drift rather than relying only on nominal amplifier offset.
अनुशंसित
Industrial Bridge Signal Conditioning
OPA131PJ can serve as the input amplifier in an instrumentation system handling low-level bridge or strain-gauge signals. The 50 pA maximum bias current reduces loading of high-resistance sensing elements, while the 4 MHz bandwidth provides ample response for many static and slowly varying industrial measurements. The 750 µV maximum input offset voltage contributes to signal accuracy, although resistor matching and calibration remain important in a complete bridge amplifier. Differential excitation, filtering, and gain stages should be evaluated together for common-mode range, output swing, and noise. The ±18 V capability is useful in industrial instrumentation using positive and negative rails, provided the selected operating point and temperature grade satisfy the equipment specification.
अनुशंसित
Low-Power Audio Buffering
OPA131PJ can buffer low-level audio or instrumentation signals where input bias current is important and a 4 MHz gain-bandwidth product is adequate. Its FET input avoids the higher bias current typical of bipolar-input amplifiers, and its 10 V/µs slew rate provides reasonable headroom for moderate signal amplitudes. The 750 µA power figure also fits low-power analog blocks. Designers should still check output swing, output-current capability, noise density, and stability when driving long cables or reactive loads. For conventional 20 kHz audio, bandwidth is generally sufficient, but gains and source impedances should be evaluated to prevent gain peaking or excessive noise. The OPA134P may be considered when its own offset, noise, and dynamic specifications offer a closer match.
अनुशंसित
Laboratory Instrumentation Buffer
OPA131PJ is useful as a general-purpose buffer in laboratory instrumentation that must combine low input loading with a wide supply range. The 50 pA maximum bias current is valuable when the source may present megohm-level impedance, while the 4 MHz bandwidth supports signal conditioning over audio and moderate measurement bandwidths. A ±18 V operating capability accommodates split-supply analog sections and simplifies grounding around bipolar sensor outputs. The amplifier should be configured with feedback close to the device, supply bypassing placed at the pins, and protection networks chosen to preserve the specified input and output ranges. For very high precision, verify offset and drift over temperature, input-voltage noise, output settling, and capacitive-load stability in the actual instrument configuration.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा OPA131PJ — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | OPA131P | OPA134P |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | PDIP-8 | PDIP-8 | PDIP-8 |
| Amplifier Type | Single FET-input operational amplifier | Single FET-input operational amplifier | Single FET-input operational amplifier |
| Gain-Bandwidth Product | 4 MHz | 4 MHz | 8 MHz |
| Maximum Input Bias Current | 50 pA | 50 pA | 5 pA |
| Maximum Input Offset Voltage | 750 µV | 750 µV | Not stated in the available source |
| Slew Rate | 10 V/µs | 10 V/µs | Not stated in the available source |
| Supply Voltage Range | ±18 V | ±18 V | Not stated in the available source |
| Power Consumption | 750 µA | 750 µA | Not stated in the available source |
| Number of Channels | 1 channel | 1 channel | 1 channel |
मुख्य विशेषताएँ
- Single-device low-leakage input specification (बनामOPA134P)
- Specified low offset for general precision signal paths (बनामOPA134P)
- Wide supply capability in a through-hole package (बनामOPA134P)
डिज़ाइन नोट्स
Place the input, feedback, and supply bypass components close to the OPA131PJ pins to minimize parasitic resistance and capacitance. For a transimpedance amplifier, keep the inverting input and feedback resistor layout compact because board leakage and stray capacitance directly affect low-current measurements. Connect the unused offset-null connection according to the manufacturer pin description and avoid long high-impedance traces near noisy switching circuitry.
Do not assume that a 50 pA maximum bias current guarantees accurate picoampere measurements if the PCB is contaminated, humidity is high, or the source has substantial leakage. Estimate the bias-current error as input bias current multiplied by total source impedance, then compare that error with the sensor resolution. Use guarded PCB practices, clean materials, and suitable protection components whose leakage is below the measurement budget.
Verify input common-mode voltage and output swing across the full supply range before using OPA131PJ with bipolar sensor signals. The 4 MHz gain-bandwidth product is sufficient for many audio and measurement applications, but high closed-loop gain, source capacitance, and load capacitance can reduce stability. Evaluate noise, slew-rate requirements, and capacitive-load behavior using the manufacturer's test conditions and the actual feedback network.
अनुपालन जानकारी
RoHS-compliant and lead-free status are identified in the OPA131PJ product information. No qualifying AEC-Q100, REACH, halogen-free, or conflict-minerals statement was identified.