Texas Instruments

OPA131PJ - 4MHz FET Op Amp, 50pA, 750uA | Texas Instruments

MPN: OPA131PJ ✓ Aktif
750 µV maximum Vdss 50 pA maximum Id 8-pin PDIP Package
MOQ: 1 |

OPA131PJ Genel Bakış

The Texas Instruments OPA131PJ is a single, general-purpose FET-input operational amplifier with a 4 MHz gain-bandwidth product, 50 pA maximum input bias current, and 750 µA power consumption. The device operates from a wide ±18 V supply range and is offered in an 8-pin PDIP package with through-hole terminals. These characteristics make it suitable for precision current measurement, low-level signal conditioning, instrumentation, sensor interfaces, and audio circuits requiring low input bias current.

A FET-input operational amplifier is an analog amplifier whose input stage uses field-effect transistors rather than bipolar input transistors. This architecture produces extremely low input bias current, making FET-input amplifiers part of the operational-amplifier hierarchy and particularly useful when measuring high-impedance sources, photodiode currents, or sensor outputs whose bias-current error must remain small. Unlike bipolar-input amplifiers, the OPA131PJ can interface with high-source-impedance nodes without loading them as heavily.

The OPA131PJ combines low offset voltage, wide bandwidth, and capacitive-load drive. Its maximum input offset voltage is 750 µV, its gain-bandwidth product is 4 MHz, and its slew rate is 10 V/µs. The ±18 V supply capability allows operation from split supplies commonly used in industrial and instrumentation systems. Power consumption of 750 µA also supports battery-powered or low-power analog designs when the circuit does not require a more power-hungry amplifier.

The OPA131 series provides single, dual, and quad configurations in industry-standard pinouts, enabling designers to standardize across different channel counts. The single OPA131 is suitable for isolated signal-conditioning channels, while dual and quad versions can implement complete analog front ends. Its 4 MHz bandwidth provides useful response for audio-frequency and general-purpose closed-loop gains while retaining useful low-bias-current behavior.

Typical uses include transimpedance amplification for optical and chemical sensors, precision current-to-voltage conversion, bridge-signal conditioning, low-leakage measurement interfaces, and buffering high-impedance transducers. The 50 pA maximum bias current is especially important when source resistance is high, while the 750 µV maximum offset voltage supports accurate low-level amplification.

When designing around the OPA131PJ, check the common-mode input range against the actual signal and supply voltages, and use the manufacturer pin-description table when assigning PCB connections. Decoupling capacitors should be placed close to the supply pins, and feedback components should be positioned to minimize parasitic capacitance. The principal trade-off is that 4 MHz bandwidth is modest compared with modern high-speed amplifiers, but it is appropriate for precision, low-power, general-purpose signal paths.

This page combines the manufacturer electrical characteristics, package and pin information, practical application guidance, and a conservative drop-in-replacement assessment. The replacement analysis distinguishes verified same-footprint options from parts that require a different package, helping engineers preserve PCB compatibility while reviewing changes in offset, bandwidth, bias current, and common-mode behavior.

Drop-in alternatifler için OPA131PJ — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.

Bu Serideki Variantlar

Yedek parça uyumlu olan aynı serideki modeller OPA131PJ (aynı form faktörü ve ayağa oturma) — farklı olan Gain-Bandwidth Product, Input Bias Current, Input Stage, Slew Rate.

Texas Instruments
Gain-Bandwidth Product: 8 MHz
Input Bias Current: 50 pA
Input Stage: True FET input
İle Karşılaştır OPA131PJ →

OPA131P

✅ Yerleştirme ⚠️ Onaylanmamış Özellikler
📦 PDIP-8
Same OPA131 electrical family and PDIP-8 footprint; ordering suffix may change temperature grade, with 0 pA rated input-bias difference

📋 Katalogda Olmayan Referans Alternatifi

OPA134PA

✅ Yerleştirme ⚠️ Onaylanmamış Özellikler
Texas Instruments
📦 PDIP-8
Single high-performance audio operational amplifier · 1 circuit · 8 MHz · 50 pA · 8 nV/√Hz · 0.00008% · 20 V/µs · 600

Fiyat için iletişime geçin

Veri Şablonunu Görüntüle →

OPA131PJ Maksimum Değerlendirmeler & Elektriksel Özellikler

Amplifier Type Single general-purpose operational amplifier
Input Bias Current 50 pA maximum
Power Consumption 750 µA
Gain-Bandwidth Product 4 MHz
Input Offset Voltage 750 µV maximum
Supply Voltage Range ±18 V
Slew Rate 10 V/µs
Input Stage FET input
Number of Channels 1 channel
Paket 8-pin PDIP
Terminal Form Through-hole
Number of Terminals 8 terminals
Package Shape Rectangular
Montaj Türü Through-hole
Capacitive Load Drive Excellent
Series Configuration Options Single, dual, and quad versions
RoHS Durumu Compliant
Lead-Free Status Lead free

OPA131PJ Pin Yapısı

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
Pin 1 NC — Not connected
Pin 2 IN- — Inverting input
Pin 3 IN+ — Non-inverting input
Pin 4 V- — Negative supply connection
Pin 5 NC — Offset null connection
Pin 6 OUT — Output
Pin 7 V+ — Positive supply connection
Pin 8 NC — Not connected

Tipik Uygulamalar

OPA131PJ için uygundur 6 uygulamas: Photodiode Transimpedance Amplification, Precision Current Measurement, High-Impedance Sensor Signal Conditioning, Industrial Bridge Signal Conditioning, Low-Power Audio Buffering, Laboratory Instrumentation Buffer.

📷

Photodiode Transimpedance Amplification

The OPA131PJ fits photodiode front ends because its FET input has a 50 pA maximum bias current, reducing the DC error created when bias current flows through a high feedback resistance. A 4 MHz gain-bandwidth product allows useful closed-loop bandwidth, while the 10 V/µs slew rate handles moderate signal changes. The transimpedance feedback network must be designed for the photodiode capacitance, and the completed circuit should be checked for stability with realistic stray capacitance. A resistor and capacitor combination around the inverting input establishes transimpedance gain and bandwidth, while the non-inverting input is usually grounded directly. OPA131PJ is preferable when low input leakage is more important than the very high bandwidth available from dedicated high-speed transimpedance amplifiers.

⚡

Precision Current Measurement

OPA131PJ is appropriate for picoampere-to-micropere current detection because the 50 pA maximum input bias current limits the measurement floor created by the amplifier itself. A transimpedance stage converts input current into a voltage that can be sampled by an ADC or control system. Its 4 MHz bandwidth supports moderate-rate measurements, and its wide ±18 V supply capability allows convenient selection of positive and negative rails. Feedback resistance and leakage around the summing node remain critical because board contamination can easily exceed the amplifier's specified bias current. Guarding, clean PCB practices, and careful capacitor selection are necessary for repeatable picoampere-class measurements.

🧩

High-Impedance Sensor Signal Conditioning

The OPA131PJ is well matched to high-impedance sensors whose output current must not be significantly loaded. Its FET input draws only 50 pA maximum bias current, while the 750 µV maximum offset voltage supports accurate amplification of low-level sensor signals. The 4 MHz gain-bandwidth product is sufficient for many pressure, chemical, humidity, and optical sensors operating below audio or low-frequency control bandwidths. The signal amplitude must remain inside the amplifier's common-mode input range, and the output must remain inside the specified swing limits. Bias-point calculations should include sensor impedance, resistor leakage, and temperature drift rather than relying only on nominal amplifier offset.

🏭

Industrial Bridge Signal Conditioning

OPA131PJ can serve as the input amplifier in an instrumentation system handling low-level bridge or strain-gauge signals. The 50 pA maximum bias current reduces loading of high-resistance sensing elements, while the 4 MHz bandwidth provides ample response for many static and slowly varying industrial measurements. The 750 µV maximum input offset voltage contributes to signal accuracy, although resistor matching and calibration remain important in a complete bridge amplifier. Differential excitation, filtering, and gain stages should be evaluated together for common-mode range, output swing, and noise. The ±18 V capability is useful in industrial instrumentation using positive and negative rails, provided the selected operating point and temperature grade satisfy the equipment specification.

🎧

Low-Power Audio Buffering

OPA131PJ can buffer low-level audio or instrumentation signals where input bias current is important and a 4 MHz gain-bandwidth product is adequate. Its FET input avoids the higher bias current typical of bipolar-input amplifiers, and its 10 V/µs slew rate provides reasonable headroom for moderate signal amplitudes. The 750 µA power figure also fits low-power analog blocks. Designers should still check output swing, output-current capability, noise density, and stability when driving long cables or reactive loads. For conventional 20 kHz audio, bandwidth is generally sufficient, but gains and source impedances should be evaluated to prevent gain peaking or excessive noise. The OPA134P may be considered when its own offset, noise, and dynamic specifications offer a closer match.

🔬

Laboratory Instrumentation Buffer

OPA131PJ is useful as a general-purpose buffer in laboratory instrumentation that must combine low input loading with a wide supply range. The 50 pA maximum bias current is valuable when the source may present megohm-level impedance, while the 4 MHz bandwidth supports signal conditioning over audio and moderate measurement bandwidths. A ±18 V operating capability accommodates split-supply analog sections and simplifies grounding around bipolar sensor outputs. The amplifier should be configured with feedback close to the device, supply bypassing placed at the pins, and protection networks chosen to preserve the specified input and output ranges. For very high precision, verify offset and drift over temperature, input-voltage noise, output settling, and capacitive-load stability in the actual instrument configuration.

Önerilen Ürünler Özeti

OPA134P Same-package low-bias-current op-amp option Kullanıldığı Yer: Photodiode Transimpedance Amplification, High-Impedance Sensor Signal Conditioning, Low-Power Audio Buffering OPA131P Same-family alternative for current-feedback interfaces Kullanıldığı Yer: Precision Current Measurement, Industrial Bridge Signal Conditioning, Laboratory Instrumentation Buffer
What are the key specifications of OPA131PJ that engineers should know?
The OPA131PJ is a single FET-input operational amplifier with a 4 MHz gain-bandwidth product, 50 pA maximum input bias current, 750 µA power consumption, and a 10 V/µs slew rate. According to the Texas Instruments OPAx131 datasheet, the device supports a wide ±18 V supply range and has a maximum input offset voltage of 750 µV. It is packaged in an 8-pin PDIP, making it suitable for through-hole instrumentation and low-leakage analog circuits.
What is the operating voltage range of OPA131PJ?
The OPA131PJ operates with a supply voltage range up to ±18 V. According to the Texas Instruments OPAx131 datasheet, this wide range supports split-supply industrial systems, laboratory instrumentation, and other analog designs that need higher common-mode headroom than a low-voltage rail-to-rail amplifier. The exact input common-mode range and output-swing limits should be checked against the signal in the design.
Why is the 50 pA bias current of OPA131PJ important?
The 50 pA maximum input bias current makes OPA131PJ suitable for high-source-impedance sensors and precision current measurements because input bias current creates a voltage error across the source impedance. According to the Texas Instruments OPAx131 datasheet, the FET input stage also supports operation with low-power circuitry through a typical 750 µA power-consumption figure. The benefit is particularly valuable for photodiode, transducer, and picoampere-class interfaces.
Where can I download the OPA131PJ datasheet PDF?
The OPA131PJ datasheet PDF is available from Texas Instruments at the official OPA131 product page and the OPAx131 datasheet link. The manufacturer document describes the OPA131 single, OPA2131 dual, and OPA4131 quad versions, including their FET-input characteristics, electrical performance, pin configurations, and applications. Use the manufacturer's version for current ordering information and qualification details.
Where can I find the OPA131PJ pinout?
The OPA131PJ pinout is found in the pin-configuration section of the Texas Instruments OPAx131 datasheet. Its 8-pin PDIP footprint uses the standard single operational-amplifier arrangement, including offset-null, inverting input, non-inverting input, negative supply, positive supply, and output connections. Use the manufacturer pin-description table when assigning every terminal, especially the offset-null and supply pins.
What can replace OPA131PJ on the same 8-pin PDIP footprint?
The OPA131P is the closest same-package replacement because it represents the same OPA131 family in an 8-pin PDIP configuration without adding a separate functional constraint. The OPA134P is another same-footprint option with different bias-current and bandwidth characteristics. Confirm supply range, common-mode range, offset, noise, output swing, and stability with capacitive loads before approving either replacement for production.
Is OPA131PJ the same as OPA131P?
The OPA131P and OPA131PJ are closely related orderable forms of the same OPA131 single-amplifier family, but the exact suffix must still be checked for temperature grade and ordering conditions. Both are identified with an 8-pin PDIP package in the relevant product information. For a direct procurement substitution, compare the manufacturer ordering table rather than assuming every grade and lifecycle condition is identical.
OPA131PJ versus OPA134P: which is better for a low-leakage sensor interface?
The OPA134P is generally preferable when input bias current is the dominant selection criterion because it belongs to a lower-bias-current FET-input family, while the OPA131PJ is specified at 50 pA maximum bias current with a 4 MHz gain-bandwidth product. Both can use an 8-pin PDIP footprint. The final choice depends on the required bandwidth, noise, supply range, offset, and output-swing specifications of the sensor interface.
When should I choose OPA131PJ instead of OPA134P?
Choose OPA131PJ when its 4 MHz gain-bandwidth product, 750 µV maximum input offset voltage, 50 pA maximum bias current, and wide ±18 V supply capability match the design. Choose OPA134P when its different bias-current and dynamic specifications provide a better fit, such as when lower input current or higher bandwidth is required. Both should be checked against noise, output swing, and common-mode limits.
Is OPA131PJ suitable for photodiode and sensor interfaces?
The OPA131PJ is suitable for many photodiode, electrochemical-sensor, and high-impedance transducer interfaces because its FET input limits input bias current to 50 pA maximum. Its 4 MHz gain-bandwidth product supports moderate-bandwidth transimpedance amplification, while the 10 V/µs slew rate supports signal transitions. The completed feedback network must still satisfy stability and bandwidth requirements.
What is the lead time and stock status for OPA131PJ?
Current stock and lead time for OPA131PJ should be obtained through the Request a Quote form on this page. The manufacturer product page is the appropriate source for lifecycle and ordering status, while the quote form can confirm current availability, minimum order quantity, and delivery timing. Commercial terms can change more quickly than the electrical characteristics and should not be treated as fixed.
Where can I buy OPA131PJ online?
Use the Request a Quote form on this page to request OPA131PJ availability, pricing, and order routing. The form is the direct commercial channel for this product page and avoids static pricing that can become outdated. For technical qualification, use the official Texas Instruments OPA131 product page and OPAx131 datasheet, and confirm the exact PDIP ordering suffix.
What is the price of OPA131PJ?
The current OPA131PJ price and quantity schedule are shown through the Request a Quote form on this page. Pricing depends on order quantity, market conditions, and fulfillment requirements, so a static unit figure would not remain current. Submit the required quantity and target supply information with the request to receive an actionable commercial quotation.
Does OPA131PJ need a heatsink or special thermal design?
The OPA131PJ normally does not require a heatsink for ordinary through-hole analog operation because its stated power consumption is 750 µA. The main thermal consideration is the total dissipation associated with supply voltage and output current, especially at high ambient temperature. Keep the device within its specified operating-temperature range and provide normal PCB airflow and copper spacing in enclosed equipment.
Is OPA131PJ RoHS compliant and suitable for lead-free assembly?
The OPA131PJ is identified as RoHS compliant and lead free in the product information. Because the OPA131PJ is an 8-pin through-hole PDIP device rather than a fine-pitch surface-mount package, its assembly still requires compatibility with the soldering process and temperature profile used by the PCB manufacturer. Use the manufacturer datasheet and package information for final production controls.

Mühendislik referans verileri: OPA131PJ — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.

Seçim Kılavuzu

Choose OPA131PJ for general-purpose precision analog designs that need a 4 MHz gain-bandwidth product, 50 pA maximum input bias current, a 750 µV maximum input offset voltage, and a ±18 V supply capability in an 8-pin PDIP package. It is particularly appropriate for high-impedance sensors, moderate-bandwidth transimpedance circuits, industrial instrumentation, and laboratory buffers. Choose OPA131P when the same electrical family and PDIP footprint are needed but the alternative ordering suffix is acceptable after checking temperature grade and lifecycle conditions. Choose OPA134P when lower input bias current or higher bandwidth is more important, since it is specified at 5 pA maximum bias current and 8 MHz gain-bandwidth product. Whichever device is selected, review common-mode range, output swing, noise, offset drift, capacitive-load stability, and power dissipation under the actual operating conditions before releasing a replacement to production.

Alternatiflerle Karşılaştırma

Parametre Bu Ürün OPA131P OPA134P
Brand Texas Instruments Texas Instruments Texas Instruments
Package PDIP-8 PDIP-8 PDIP-8
Amplifier Type Single FET-input operational amplifier Single FET-input operational amplifier Single FET-input operational amplifier
Gain-Bandwidth Product 4 MHz 4 MHz 8 MHz
Maximum Input Bias Current 50 pA 50 pA 5 pA
Maximum Input Offset Voltage 750 µV 750 µV Not stated in the available source
Slew Rate 10 V/µs 10 V/µs Not stated in the available source
Supply Voltage Range ±18 V ±18 V Not stated in the available source
Power Consumption 750 µA 750 µA Not stated in the available source
Number of Channels 1 channel 1 channel 1 channel

Ana Farklılayıcılar

  • Single-device low-leakage input specification (karşılaştırma:OPA134P)
  • Specified low offset for general precision signal paths (karşılaştırma:OPA134P)
  • Wide supply capability in a through-hole package (karşılaştırma:OPA134P)

Tasarım Notları

Place the input, feedback, and supply bypass components close to the OPA131PJ pins to minimize parasitic resistance and capacitance. For a transimpedance amplifier, keep the inverting input and feedback resistor layout compact because board leakage and stray capacitance directly affect low-current measurements. Connect the unused offset-null connection according to the manufacturer pin description and avoid long high-impedance traces near noisy switching circuitry.

Do not assume that a 50 pA maximum bias current guarantees accurate picoampere measurements if the PCB is contaminated, humidity is high, or the source has substantial leakage. Estimate the bias-current error as input bias current multiplied by total source impedance, then compare that error with the sensor resolution. Use guarded PCB practices, clean materials, and suitable protection components whose leakage is below the measurement budget.

Verify input common-mode voltage and output swing across the full supply range before using OPA131PJ with bipolar sensor signals. The 4 MHz gain-bandwidth product is sufficient for many audio and measurement applications, but high closed-loop gain, source capacitance, and load capacitance can reduce stability. Evaluate noise, slew-rate requirements, and capacitive-load behavior using the manufacturer's test conditions and the actual feedback network.

Uyumluluk Bilgisi

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Kadmiyumdan Arınmış
Yes
Klorofillerden Arınmış
Unknown
Çatışma Minerali
Unknown

RoHS-compliant and lead-free status are identified in the OPA131PJ product information. No qualifying AEC-Q100, REACH, halogen-free, or conflict-minerals statement was identified.

Veri doğrulanma tarihi: 2026-11-19 — XAIPART bileşen mühendislik ekibi tarafından doğrulanmış ve derlenmiş veri

İlgili Aramalar

OPA131PJ datasheet OPA131PJ pinout OPA131PJ datasheet pdf OPA131PJ equivalent OPA131PJ replacement OPA131PJ cross reference OPA131PJ vs OPA134P OPA131PJ PDIP-8 pinout OPA131PJ application circuit OPA131PJ price OPA131PJ stock Texas Instruments OPA131PJ OPA131PJ photodiode amplifier OPA131PJ low bias current op amp OPA131PJ 4MHz operational amplifier

İlgili Bileşenler ve Terimler

Texas Instruments OPA131PJ OPA131P OPA134P OPA131 OPA2131 OPA4131 FET-input operational amplifier operational amplifier analog amplifier semiconductor input bias current input offset voltage gain-bandwidth product slew rate PDIP-8 DIP package family through-hole package surface-mount device transimpedance amplifier high-impedance sensor photodiode industrial instrumentation RoHS lead-free
Hızlı Teklif RFQ
Detayları tam doldurun — satış ekibimiz 24 saat içinde yanıt verecek
Parça Numarası Üretici Paket QTY Hedef Fiyat Genişletilmiş
✓
Teklif gönderildi!

24 saat içinde e-postanıza yanıt vereceğiz

1
RFQ Gönderildi
2
Teklif Alındı
3
Sipariş Yerleştirildi
4
Ödeme
5
Gönderildi
6
Teslim Edildi
RFQ Detaylarını Görüntüle