OPA207ID - Low-Noise Precision Op Amp | Texas Instruments
MPN: OPA207ID ✓ सक्रियOPA207ID अवलोकन
An operational amplifier, or op amp, is a voltage-gain circuit used to amplify the voltage difference between its two inputs. Within the analog IC hierarchy, the OPA207ID belongs to the amplifier IC family, where its precision, low-noise characteristics support measurement, reference, buffering, and feedback-control circuits where signal integrity is more important than wide bandwidth or lowest power consumption.
The principal features of the OPA207ID include improved noise performance, wider output-voltage swing, twice the speed and half the quiescent current of the industry-standard OP-07, OP-77, and OP-177 amplifiers it is designed to replace. Its 350 µA supply current supports low-power operation, while 7.5 nV/√Hz noise and 100 µV input offset voltage target high-accuracy signal chains. The 0.2 µV/°C drift specification helps maintain calibration accuracy as temperature changes.
Technically, the OPA207 uses a bipolar input and output architecture with low input bias current, high common-mode rejection ratio, and high power-supply rejection ratio. These characteristics reduce errors caused by input biasing, common-mode voltage, and supply-rail variation. Its rail-to-rail output allows the output voltage to approach the positive and negative supply limits more closely than a conventional precision amplifier, improving dynamic range in restricted supply-voltage designs.
Typical uses include precision current sensing, sensor-signal conditioning, low-level transducer amplification, buffered references, laboratory instrumentation, and industrial control loops. The combination of low noise, low offset drift, low bias current, and low quiescent current makes the device appropriate when measurement error must remain small while operating from limited power.
Designers should review the input common-mode range, output swing, stability requirements, and noise-gain curve before finalizing compensation. Decoupling capacitors should be placed close to the supply pins, and sensitive feedback paths should be kept short and isolated from switching nodes to preserve the benefit of the 7.5 nV/√Hz input-noise specification.
This product page combines the manufacturer specifications, lifecycle and package information, practical application guidance, and verified sourcing information. It also distinguishes exact package and order-code considerations so engineers can evaluate OPA207ID suitability without confusing it with the smaller-footprint OPA207IDBVR version.
के लिए ड्रॉप-इन विकल्प OPA207ID — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस उत्पाद के लिए कोई drop-in alternatives उपलब्ध नहीं।
विकल्प अनुरोध करेंOPA207ID Maximum Ratings और Electrical Characteristics
| Operational Amplifier Type | Precision bipolar operational amplifier |
| Number of Channels | 1 circuit |
| क्वाइसेंट करंट | 350 µA |
| Input Voltage Noise Density | 7.5 nV/√Hz |
| Input Offset Voltage | 100 µV |
| Input Offset Voltage Drift | 0.2 µV/°C |
| Maximum Supply Voltage | 36 V |
| Output Swing | Rail-to-rail output |
| पैकेज | 8-SOIC, 0.154 inch width, 3.90 mm width |
| माउंटिंग प्रकार | Surface mount |
| Automotive Qualification | Not applicable to the standard OPA207ID ordering designation |
OPA207ID 8-soic, 0.154 inch width, 3.90 mm width पिन कॉन्फ़िगरेशन गाइड
OPA207ID (8-soic, 0.154 inch width, 3.90 mm width पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस एनालॉग कंपोनेंट में इनपुट, आउटपुट और पावर सप्लाई पिन हैं। ऑफ़सेट नल, कम्पनसेशन और एनेबल पिन कॉन्फ़िगरेशन के लिए निर्माता डेटाशीट देखें। सिग्नल कंडीशनिंग और एम्प्लीफ़ायर सर्किट के लिए आदर्श।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: OPA207ID.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
OPA207ID के लिए उपयुक्त है 6 अनुप्रयोगs: Precision Sensor Signal Conditioning, Precision Current Sensing, Low-Noise Buffering, Instrumentation and Reference Circuits, Transducer and Bridge Measurement, Low-Power Portable Measurement.
Precision Sensor Signal Conditioning
The OPA207ID fits low-level sensor front ends because its 100 µV input offset voltage, 0.2 µV/°C offset drift, and 7.5 nV/√Hz input noise limit the error introduced when amplifying small differential signals. Its low input bias current also reduces errors in high-impedance sensor networks. Place the amplifier close to the sensor or differential input network, use short feedback paths, and verify common-mode range at the highest sensor voltage. The rail-to-rail output improves usable swing when operating from a constrained supply, while the 350 µA quiescent current supports portable instrumentation.
अनुशंसित
Precision Current Sensing
OPA207ID is appropriate for current-shunt measurement when low offset, low drift, and low noise determine measurement accuracy. Its 100 µV offset specification limits residual error near the zero-current state, while the 0.2 µV/°C drift specification helps preserve calibration as board temperature changes. The 7.5 nV/√Hz noise density supports resolving small voltage changes across a shunt. Keep the shunt and amplifier on the same thermally stable area, use Kelvin routing where practical, and confirm that the shunt voltage remains within the amplifier’s input common-mode range.
अनुशंसित
Low-Noise Buffering
The OPA207ID can buffer high-impedance sources without adding excessive noise or offset error. Its 7.5 nV/√Hz input-noise density, low input bias current, and high common-mode rejection ratio help preserve weak source signals, while the rail-to-rail output gives the following stage more usable voltage range. Use the device as a voltage follower only after checking stability and capacitive-load limits for the specific gain configuration. Keep the input lead short, avoid leakage-prone board surfaces, and use a clean ground return to prevent buffer current from becoming part of the measured signal.
अनुशंसित
Instrumentation and Reference Circuits
OPA207ID is useful in laboratory and industrial instrumentation where offset stability and low-noise behavior affect measurement credibility. The 100 µV input offset voltage and 0.2 µV/°C drift specification provide a defined starting point for error budgets, while 350 µA quiescent current enables multi-channel designs with constrained power budgets. Use clean supply bypassing at the package pins, route analog returns carefully, and separate sensitive inputs from digital and switching circuitry. Calibration should include both offset and temperature effects when the instrument operates across a wide environmental range.
अनुशंसित
Transducer and Bridge Measurement
The OPA207ID can amplify small differential outputs from strain, pressure, and resistance bridges while its low offset and low drift reduce errors relative to the bridge excitation. Its low input bias current minimizes loading of high-impedance bridges, and its high common-mode rejection ratio helps reject supply and common-mode disturbances when those ratios meet the design requirements. Choose gain carefully to avoid unnecessary noise gain, confirm the input common-mode limits across bridge tolerance and excitation range, and provide local supply decoupling. For highest precision, evaluate offset, drift, noise, and bridge excitation variations together in the error budget.
अनुशंसित
Low-Power Portable Measurement
OPA207ID suits portable measurement systems where each analog channel contributes to battery consumption and signal error. Its 350 µA quiescent current is the baseline supply demand, while low noise, low offset voltage, and low offset drift improve the useful dynamic range of compact sensor modules. The rail-to-rail output can reduce the required supply span in low-voltage systems. Power the 8-pin SOIC from a low-noise source, place bypass capacitors close to the supply pins, and account for output-current demand in the overall power budget. Enable the circuit only when measurement is required when the system architecture supports shutdown control externally.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा OPA207ID — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
मुख्य विशेषताएँ
- Lower offset drift for temperature-sensitive precision measurements (बनामOP-07)
- Lower quiescent current for multi-channel and portable systems (बनामOP-177)
- Improved noise performance in low-level analog paths (बनामOP-77)
डिज़ाइन नोट्स
Place the supply bypass capacitor and any permitted output or feedback capacitors close to their corresponding OPA207ID pins. Keep sensitive input and feedback traces short, avoid routing them beneath digital or switching traces, and provide a continuous ground reference to the source. For a precision measurement design, use separate analog and return paths where possible and evaluate the complete return current rather than relying only on component placement.
Treat input bias current, leakage, and noise gain as an integrated error budget. The 7.5 nV/√Hz input-noise specification is useful only when the source impedance, feedback resistors, board leakage, and operating noise bandwidth are also controlled. Check resistor thermal noise and avoid excessively large feedback values when they increase Johnson noise or slow settling. Validate the chosen gain and compensation with the final source and load capacitances.
Do not assume that every OPA207 package option is mechanically interchangeable with OPA207ID. The OPA207ID uses an 8-pin SOIC, whereas OPA207IDBVR uses SOT-23-5; changing between them requires a different PCB land pattern. Also check input common-mode range and output swing against the actual supply voltage, because the rail-to-rail output description does not imply rail-to-rail input operation.
The OPA207ID is a low-power precision amplifier, but final thermal margin should be checked from the maximum supply voltage, output swing, load current, and ambient temperature. Use the manufacturer’s power-dissipation and junction-temperature limits rather than estimating reliability from the 350 µA quiescent current alone. Place the SOIC on an appropriate copper area when operating near the maximum electrical limits, and ensure airflow or conduction keeps the device within its rated temperature range.
अनुपालन जानकारी
No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration for OPA207ID was identified. The standard OPA207ID ordering designation is not presented as an automotive-qualified variant.