Texas Instruments

OPA207ID - Low-Noise Precision Op Amp | Texas Instruments

MPN: OPA207ID ✓ Aktif
7.5 nV/√Hz Vdss 350 µA Id 8-SOIC, 0.154 inch width, 3.90 mm width Package
MOQ: 1 |

OPA207ID Ringkasan

The Texas Instruments OPA207ID is a low-power, high-precision bipolar operational amplifier with 350 µA quiescent current, 7.5 nV/√Hz input noise, 100 µV input offset voltage, and 0.2 µV/°C offset drift. It is packaged in an 8-pin SOIC and provides a rail-to-rail output stage for precision analog signal-conditioning applications.

An operational amplifier, or op amp, is a voltage-gain circuit used to amplify the voltage difference between its two inputs. Within the analog IC hierarchy, the OPA207ID belongs to the amplifier IC family, where its precision, low-noise characteristics support measurement, reference, buffering, and feedback-control circuits where signal integrity is more important than wide bandwidth or lowest power consumption.

The principal features of the OPA207ID include improved noise performance, wider output-voltage swing, twice the speed and half the quiescent current of the industry-standard OP-07, OP-77, and OP-177 amplifiers it is designed to replace. Its 350 µA supply current supports low-power operation, while 7.5 nV/√Hz noise and 100 µV input offset voltage target high-accuracy signal chains. The 0.2 µV/°C drift specification helps maintain calibration accuracy as temperature changes.

Technically, the OPA207 uses a bipolar input and output architecture with low input bias current, high common-mode rejection ratio, and high power-supply rejection ratio. These characteristics reduce errors caused by input biasing, common-mode voltage, and supply-rail variation. Its rail-to-rail output allows the output voltage to approach the positive and negative supply limits more closely than a conventional precision amplifier, improving dynamic range in restricted supply-voltage designs.

Typical uses include precision current sensing, sensor-signal conditioning, low-level transducer amplification, buffered references, laboratory instrumentation, and industrial control loops. The combination of low noise, low offset drift, low bias current, and low quiescent current makes the device appropriate when measurement error must remain small while operating from limited power.

Designers should review the input common-mode range, output swing, stability requirements, and noise-gain curve before finalizing compensation. Decoupling capacitors should be placed close to the supply pins, and sensitive feedback paths should be kept short and isolated from switching nodes to preserve the benefit of the 7.5 nV/√Hz input-noise specification.

This product page combines the manufacturer specifications, lifecycle and package information, practical application guidance, and verified sourcing information. It also distinguishes exact package and order-code considerations so engineers can evaluate OPA207ID suitability without confusing it with the smaller-footprint OPA207IDBVR version.

Pilihan pengganti yang segera untuk OPA207ID — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

Tiada pilihan pengganti yang segera untuk produk ini.

Minta Alternatif

OPA207ID Penilaian maksimum & Ciri-ciri Elektrik

Operational Amplifier Type Precision bipolar operational amplifier
Number of Channels 1 circuit
Arus Dalam Tentera 350 µA
Input Voltage Noise Density 7.5 nV/√Hz
Input Offset Voltage 100 µV
Input Offset Voltage Drift 0.2 µV/°C
Maximum Supply Voltage 36 V
Output Swing Rail-to-rail output
Kemasan 8-SOIC, 0.154 inch width, 3.90 mm width
Jenis Pemasangan Surface mount
Automotive Qualification Not applicable to the standard OPA207ID ordering designation

Panduan Konfigurasi Pin OPA207ID 8-soic, 0.154 inch width, 3.90 mm width

Konfigurasi pin untuk OPA207ID (8-soic, 0.154 inch width, 3.90 mm width pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.

Garis bentuk pengecah pakai 8-soic, 0.154 inch width, 3.90 mm width untuk OPA207ID

Tiada data garisan pin yang diperoleh untuk OPA207ID.

Rujuk kepada lembaran data untuk konfigurasi pin penuh.

Aplikasi Biasa

OPA207ID patut untuk 6 aplikasis: Precision Sensor Signal Conditioning, Precision Current Sensing, Low-Noise Buffering, Instrumentation and Reference Circuits, Transducer and Bridge Measurement, Low-Power Portable Measurement.

🧩

Precision Sensor Signal Conditioning

The OPA207ID fits low-level sensor front ends because its 100 µV input offset voltage, 0.2 µV/°C offset drift, and 7.5 nV/√Hz input noise limit the error introduced when amplifying small differential signals. Its low input bias current also reduces errors in high-impedance sensor networks. Place the amplifier close to the sensor or differential input network, use short feedback paths, and verify common-mode range at the highest sensor voltage. The rail-to-rail output improves usable swing when operating from a constrained supply, while the 350 µA quiescent current supports portable instrumentation.

⚡

Precision Current Sensing

OPA207ID is appropriate for current-shunt measurement when low offset, low drift, and low noise determine measurement accuracy. Its 100 µV offset specification limits residual error near the zero-current state, while the 0.2 µV/°C drift specification helps preserve calibration as board temperature changes. The 7.5 nV/√Hz noise density supports resolving small voltage changes across a shunt. Keep the shunt and amplifier on the same thermally stable area, use Kelvin routing where practical, and confirm that the shunt voltage remains within the amplifier’s input common-mode range.

📡

Low-Noise Buffering

The OPA207ID can buffer high-impedance sources without adding excessive noise or offset error. Its 7.5 nV/√Hz input-noise density, low input bias current, and high common-mode rejection ratio help preserve weak source signals, while the rail-to-rail output gives the following stage more usable voltage range. Use the device as a voltage follower only after checking stability and capacitive-load limits for the specific gain configuration. Keep the input lead short, avoid leakage-prone board surfaces, and use a clean ground return to prevent buffer current from becoming part of the measured signal.

🏭

Instrumentation and Reference Circuits

OPA207ID is useful in laboratory and industrial instrumentation where offset stability and low-noise behavior affect measurement credibility. The 100 µV input offset voltage and 0.2 µV/°C drift specification provide a defined starting point for error budgets, while 350 µA quiescent current enables multi-channel designs with constrained power budgets. Use clean supply bypassing at the package pins, route analog returns carefully, and separate sensitive inputs from digital and switching circuitry. Calibration should include both offset and temperature effects when the instrument operates across a wide environmental range.

🏭

Transducer and Bridge Measurement

The OPA207ID can amplify small differential outputs from strain, pressure, and resistance bridges while its low offset and low drift reduce errors relative to the bridge excitation. Its low input bias current minimizes loading of high-impedance bridges, and its high common-mode rejection ratio helps reject supply and common-mode disturbances when those ratios meet the design requirements. Choose gain carefully to avoid unnecessary noise gain, confirm the input common-mode limits across bridge tolerance and excitation range, and provide local supply decoupling. For highest precision, evaluate offset, drift, noise, and bridge excitation variations together in the error budget.

📱

Low-Power Portable Measurement

OPA207ID suits portable measurement systems where each analog channel contributes to battery consumption and signal error. Its 350 µA quiescent current is the baseline supply demand, while low noise, low offset voltage, and low offset drift improve the useful dynamic range of compact sensor modules. The rail-to-rail output can reduce the required supply span in low-voltage systems. Power the 8-pin SOIC from a low-noise source, place bypass capacitors close to the supply pins, and account for output-current demand in the overall power budget. Enable the circuit only when measurement is required when the system architecture supports shutdown control externally.

What are the key specifications of OPA207ID that engineers should know?
The OPA207ID is a single-channel precision bipolar op amp with 350 µA quiescent current, 7.5 nV/√Hz input noise, 100 µV input offset voltage, and 0.2 µV/°C offset drift. It also uses a rail-to-rail output stage and is offered in an 8-pin SOIC package. According to the Texas Instruments OPA207 datasheet, the device is intended to improve on the OP-07, OP-77, and OP-177 while consuming less power and operating faster.
Where can I download the OPA207ID datasheet PDF?
The OPA207ID datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/gpn/OPA207. The document contains the electrical characteristics, package drawings, pin configuration, typical performance curves, and ordering information for the OPA207 family. Use the ordering table to confirm that OPA207ID denotes the 8-pin SOIC tube version rather than the SOT-23-5 or tape-and-reel ordering codes.
Where can I find the OPA207ID pinout and package drawing?
The OPA207ID pin configuration and package drawing are shown in the Pin Configuration and Mechanical Data sections of the Texas Instruments OPA207 datasheet. The device uses an 8-pin SOIC package with 0.154-inch body width, corresponding to the 3.90 mm body width identified for this ordering code. Use the package drawing on this page to confirm land-pattern dimensions and compare the physical footprint with the target PCB.
Is OPA207ID suitable for precision sensor signal conditioning?
Yes, the OPA207ID is well suited to precision sensor signal conditioning because its input offset voltage is 100 µV, input offset drift is 0.2 µV/°C, and input noise density is 7.5 nV/√Hz. According to the Texas Instruments OPA207 datasheet, low input bias current and high common-mode rejection ratio also reduce errors around sensor outputs. The rail-to-rail output stage provides additional output range when the amplifier operates from limited supply voltages.
How does OPA207ID compare with OP-07, OP-77, and OP-177?
The OPA207ID is designed as a lower-power and faster precision alternative to the OP-07, OP-77, and OP-177 families. According to the Texas Instruments OPA207 datasheet, it provides improved noise performance, a wider output-voltage swing, twice the speed, and half the quiescent current of those industry-standard alternatives. Direct substitution still requires checking supply voltage, input common-mode range, output swing, compensation, and exact pin compatibility for the selected device.
What is the best drop-in replacement for OPA207ID?
No independently validated drop-in replacement is identified on this page because a substitute must match the 8-pin SOIC footprint and remain within the key electrical limits of the OPA207ID. The OPA207IDR has the same 8-SOIC package but is a tape-and-reel carrier variant, while OPA207IDBVR uses SOT-23-5 and is not footprint-compatible. Use the Texas Instruments cross-reference search and compare the complete electrical tables before approving any substitution.
Can OPA207IDR replace OPA207ID on the same PCB?
The OPA207IDR can use the same 8-SOIC footprint and electrical configuration as OPA207ID, but it is the tape-and-reel order code rather than the tube-pack OPA207ID order code. Texas Instruments lists both as active package variants of the OPA207 family. A PCB populated with OPA207ID may therefore accept OPA207IDR electrically and mechanically, provided production quantities, carrier format, labeling, and sourcing requirements are reviewed.
What is the best cross-brand equivalent for OPA207ID?
A specific cross-brand equivalent cannot be recommended responsibly without a verified 8-pin SOIC pinout and a side-by-side comparison of offset, drift, noise, bias current, bandwidth, common-mode range, and supply limits. The available cross-reference results identify lookup tools but do not establish a qualified substitute for OPA207ID. Use the Request a Quote form for sourcing help, and require the candidate manufacturer to confirm pin compatibility and application-specific performance before replacing the Texas Instruments device.
When should I choose OPA207ID instead of OPA207IDBVR?
Choose OPA207ID when the PCB is designed for an 8-pin SOIC footprint, particularly for tube-pack production or an existing instrumentation layout. Choose OPA207IDBVR when the board uses the smaller SOT-23-5 footprint and requires that order code. Both belong to the OPA207 family, but the package dimensions, land pattern, carrier format, and placement requirements differ, so OPA207IDBVR is not a physical drop-in substitute for OPA207ID.
Is OPA207ID the same as OPA207IDR?
The OPA207ID and OPA207IDR use the same 8-SOIC package and correspond to the same OPA207 family configuration, but their order codes identify different carrier formats. Texas Instruments identifies OPA207ID as the tube-pack ordering option and OPA207IDR as the tape-and-reel option. Their electrical performance is intended to match, while handling, reel quantity, labeling, and production logistics determine which code is more appropriate for a given assembly process.
What can replace OPA207ID in a precision amplifier circuit?
OPA207ID should be replaced only with a device that has the same 8-pin SOIC pin arrangement and satisfies the circuit’s offset, drift, noise, bias-current, bandwidth, common-mode, output-swing, and supply requirements. The OPA207IDR is an order-code alternative in the same package, but it is not an independent functional upgrade. For a cross-brand replacement, compare the full Texas Instruments OPA207 datasheet limits against the candidate datasheet and verify stability at the actual noise gain.
How much current does OPA207ID consume?
The OPA207ID has a specified quiescent current of 350 µA. According to the Texas Instruments OPA207 product page and OPA207 datasheet, this is half the quiescent current of the industry-standard OP-07, OP-77, and OP-177 alternatives for which it is intended as an improvement. Actual circuit demand increases with output current and operating frequency, so the quiescent figure should be used as the baseline rather than the maximum system consumption.
Where can I buy OPA207ID and check current stock?
Use the Request a Quote form on this page to request OPA207ID availability, current lead time, order quantity, and tube-pack packaging information. The manufacturer lists the OPA207ID as an active ordering option with a standard package quantity of 75 units. Stock and delivery timing can change, so request a written quotation for the exact quantity and ship-to requirements rather than relying on a historical listing count.
What is the price of OPA207ID?
Use the Request a Quote form on this page for the current OPA207ID price, quantity breaks, stock, and lead time. Market pricing depends on order quantity, tube-pack packaging, and current supply conditions, so a historical unit price should not be treated as a quotation. The structured pricing area on this page is updated separately, and the quote request provides the appropriate route for a purchase decision based on current commercial conditions.
Is OPA207ID in stock and what is its lead time?
Request current OPA207ID stock and lead time through the Request a Quote form on this page. Texas Instruments identifies OPA207ID as an active part ordered in a tube with a standard package quantity of 75 units, but live inventory and lead time vary with order volume and logistics. Specify the required quantity, delivery date, and ship-to location so the supplier can confirm the current commitment rather than presenting an outdated availability estimate.

Data referensi kejuruteraan untuk OPA207ID — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose OPA207ID when the design needs a precision single amplifier with 350 µA quiescent current, 7.5 nV/√Hz input noise, 100 µV offset voltage, low drift, and an 8-pin SOIC footprint. It is particularly suitable for current sensing, bridge measurement, sensor conditioning, reference buffering, and portable instrumentation where power and measurement error both matter. Choose OPA207IDR when the same 8-SOIC configuration is needed but production handling calls for tape-and-reel rather than the tube-pack OPA207ID order code. Choose OPA207IDBVR only when the PCB already uses SOT-23-5; it is not a drop-in mechanical replacement. For a different manufacturer, require a documented 8-pin SOIC pinout and a complete comparison of offset, drift, noise, bias current, bandwidth, slew rate, common-mode range, output swing, supply range, and stability before approving a substitution.

Penyeberangsung Jelas

  • Lower offset drift for temperature-sensitive precision measurements (vsOP-07)
  • Lower quiescent current for multi-channel and portable systems (vsOP-177)
  • Improved noise performance in low-level analog paths (vsOP-77)

Catatan Desain

Place the supply bypass capacitor and any permitted output or feedback capacitors close to their corresponding OPA207ID pins. Keep sensitive input and feedback traces short, avoid routing them beneath digital or switching traces, and provide a continuous ground reference to the source. For a precision measurement design, use separate analog and return paths where possible and evaluate the complete return current rather than relying only on component placement.

Treat input bias current, leakage, and noise gain as an integrated error budget. The 7.5 nV/√Hz input-noise specification is useful only when the source impedance, feedback resistors, board leakage, and operating noise bandwidth are also controlled. Check resistor thermal noise and avoid excessively large feedback values when they increase Johnson noise or slow settling. Validate the chosen gain and compensation with the final source and load capacitances.

Do not assume that every OPA207 package option is mechanically interchangeable with OPA207ID. The OPA207ID uses an 8-pin SOIC, whereas OPA207IDBVR uses SOT-23-5; changing between them requires a different PCB land pattern. Also check input common-mode range and output swing against the actual supply voltage, because the rail-to-rail output description does not imply rail-to-rail input operation.

The OPA207ID is a low-power precision amplifier, but final thermal margin should be checked from the maximum supply voltage, output swing, load current, and ambient temperature. Use the manufacturer’s power-dissipation and junction-temperature limits rather than estimating reliability from the 350 µA quiescent current alone. Place the SOIC on an appropriate copper area when operating near the maximum electrical limits, and ensure airflow or conduction keeps the device within its rated temperature range.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration for OPA207ID was identified. The standard OPA207ID ordering designation is not presented as an automotive-qualified variant.

Data disahkan pada: 2026-11-19 — data yang disahkan dan disusun semula oleh pasukan kejuruteraan komponen XAIPART

Pencarian Berhubungan

OPA207ID datasheet OPA207ID datasheet pdf OPA207ID pinout OPA207ID equivalent OPA207ID replacement OPA207ID cross reference OPA207ID price OPA207ID stock Texas Instruments OPA207ID OPA207ID 8-SOIC OPA207ID low noise op amp OPA207ID vs OPA207IDR

Komponen dan Tanda berkaitan

Texas Instruments OPA207ID OPA207IDR OPA207IDBVR OPA207 operational amplifier precision operational amplifier amplifier IC analog IC semiconductor bipolar architecture rail-to-rail output low-dropout amplifier low-noise op amp quiescent current input voltage noise density input offset voltage input offset voltage drift common-mode rejection ratio power-supply rejection ratio 8-SOIC SOIC package family surface-mount package precision instrumentation sensor signal conditioning current sensing
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ