OPA241UA - 25µA Micro-Power Op Amp | Texas Instruments
MPN: OPA241UA ✓ सक्रियOPA241UA अवलोकन
An operational amplifier is a voltage-feedback analog building block that amplifies the difference between two input voltages while presenting high input impedance and low output impedance. The OPA241 belongs to the low-dropout, micropower operational-amplifier hierarchy within analog and mixed-signal semiconductors. Its low operating current makes it suitable for sensor interfaces, portable instrumentation, battery monitoring, and low-duty-cycle control systems where continuous amplifier power would dominate the system budget.
The principal operating characteristics are a 25 µA supply current, 35 kHz gain-bandwidth product, 0.01 V/µs slew rate, and operation from a single 5 V supply. The device also provides rail-to-rail output swing, which increases usable output range on low-voltage rails. Low offset voltage supports accurate amplification of small sensor signals, while the high common-mode rejection ratio reduces sensitivity to supply and ground-disturbance signals. A unity-gain bandwidth of 35 kHz makes the amplifier appropriate for low-frequency signal conditioning rather than high-speed waveform processing.
OPA241UA is a single-amplifier implementation in the broader OPAx241 family, alongside the OPA2241 and OPA4241 dual and quad versions. The family targets portable applications where low power consumption, common-mode range, and output swing are more important than wideband performance. Single-supply operation also simplifies battery-powered design, while the small SOIC package supports conventional surface-mount assembly.
Typical uses include low-power sensor amplification, portable measurement equipment, battery-current monitoring, industrial signal conditioning, and low-leakage sensing interfaces. In these applications, the amplifier can sit close to a sensor and condition its output before conversion or transmission. The 35 kHz bandwidth is adequate for slow physiological, temperature, pressure, and position signals, but it is not intended for high-speed communications, pulse shaping, or precision audio workloads.
For a new design, verify the signal bandwidth, output load, common-mode range, and stability requirements against the manufacturer datasheet. Place the bypass capacitor close to the supply pins and avoid capacitive loading that can reduce phase margin. The low-current advantage should also be checked against the complete analog signal chain, since additional amplifiers, converters, and protection devices can consume more power than the OPA241UA itself.
This product page consolidates the manufacturer specifications, commercial sourcing guidance, package details, cross-reference alternatives, and application-focused engineering notes. It supports faster part selection by connecting the OPA241UA electrical limits with practical low-power circuit requirements rather than repeating only the basic ordering information.
के लिए ड्रॉप-इन विकल्प OPA241UA — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस सीरीज़ के वेरिएंट
समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं OPA241UA (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Amplifier Type, Number of Channels, Operating Temperature Range, Package, Slew Rate.
OPA241UAG4
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
AD8676ARZ
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →LT6015
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
MAX44246
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
OPA241UA Maximum Ratings और Electrical Characteristics
| Amplifier Type | Single operational amplifier |
| Supply Type | Single supply |
| Nominal Supply Voltage | 5 V |
| क्वाइसेंट करंट | 25 µA |
| Gain-Bandwidth Product | 35 kHz |
| Slew Rate | 0.01 V/µs |
| Supply Voltage Range | ±1.35 V to ±18 V |
| Output Swing | Rail-to-rail |
| Offset Voltage | Low |
| Common-Mode Rejection | High |
| Open-Loop Gain | High |
| Number of Channels | 1 channel |
| पिन की संख्या | 8 pins |
| पैकेज | 8-pin SOIC |
| माउंटिंग प्रकार | Surface mount |
| Application | Battery-powered portable applications |
| ऑपरेटिंग तापमान रेंज | -40 °C to +85 °C |
OPA241UA 8-pin soic पिन कॉन्फ़िगरेशन गाइड
OPA241UA (8-pin soic पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस एनालॉग कंपोनेंट में इनपुट, आउटपुट और पावर सप्लाई पिन हैं। ऑफ़सेट नल, कम्पनसेशन और एनेबल पिन कॉन्फ़िगरेशन के लिए निर्माता डेटाशीट देखें। सिग्नल कंडीशनिंग और एम्प्लीफ़ायर सर्किट के लिए आदर्श।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: OPA241UA.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
OPA241UA के लिए उपयुक्त है 6 अनुप्रयोगs: Battery-Powered Sensor Interfaces, Portable Medical Instrumentation, Industrial Process Measurement, Battery Current Monitoring, Low-Power Data Acquisition, Precision Voltage Buffering.
Battery-Powered Sensor Interfaces
The OPA241UA is suitable for conditioning outputs from temperature, pressure, position, and electrochemical sensors in battery-operated equipment. Its 25 µA quiescent current limits the amplifier's contribution to standby power, while the 35 kHz gain-bandwidth product accommodates slow sensor signals without requiring a wideband amplifier. Place the device close to the sensor and use local supply bypassing to minimize sensitive traces and susceptibility to external interference. The rail-to-rail output can improve signal range on low-voltage rails, although the complete input and output ranges must remain within the datasheet limits for the selected gain and load.
अनुशंसित
Portable Medical Instrumentation
The OPA241UA can amplify low-level physiological or diagnostic signals in portable instruments where every microamp of supply current affects battery life. Its 25 µA quiescent current, low offset voltage, high common-mode rejection, and high open-loop gain support accurate amplification around a low-voltage analog front end. The 35 kHz bandwidth is appropriate for many ECG, pressure, and biochemical monitoring waveforms that remain below the amplifier's useful frequency range. Verify electrode protection, input bias-current error, patient-safety isolation, and applicable medical requirements independently of the amplifier's electrical performance.
अनुशंसित
Industrial Process Measurement
OPA241UA suits low-frequency industrial sensor chains where a 24 V source must be reduced to a compact, low-energy analog signal. Although the device is identified for 5 V single-supply operation, its documented supply range permits other suitable operating rails. The 25 µA supply current reduces power in remote monitoring loops, and the 0.01 V/µs slew rate supports slow process variables with reasonable small-signal bandwidth. Add protection against industrial transients and verify the exact input common-mode range, output swing, and grounding strategy before connecting field-wired sensors.
अनुशंसित
Battery Current Monitoring
The OPA241UA can amplify the voltage across a low-value shunt when monitoring current consumption in a portable battery system. Its low 25 µA supply current prevents the measurement amplifier from materially changing the load being measured, while low offset voltage supports accurate recovery of small voltage differences. The 35 kHz bandwidth is suitable for relatively slow charge and discharge current profiles rather than fast pulse currents. Use a Kelvin connection, high-side or low-side topology appropriate to the system ground, and an input filter sized against the shunt impedance and amplifier noise requirements.
अनुशंसित
Low-Power Data Acquisition
OPA241UA is useful in compact, low-duty-cycle data-acquisition systems that amplify sensor outputs before conversion and control overall energy use. The 25 µA quiescent current is beneficial when the acquisition node must operate throughout a long battery life, and the single 5 V supply simplifies system partitioning. The 35 kHz gain-bandwidth product is sufficient for many environmental, occupancy, and condition-monitoring inputs but not for high-speed vibration analysis. Select the gain and output range for the converter, account for settling time, and preserve a clean analog return path between the sensor, amplifier, and converter.
अनुशंसित
Precision Voltage Buffering
OPA241UA can provide voltage buffering and gain for low-level reference or control signals in compact portable equipment. Its high open-loop gain reduces output error when driving a moderate load, while low offset voltage helps preserve small reference levels. The rail-to-rail output increases the available range near the supply rails, and the 0.01 V/µs slew rate is sufficient for slowly changing control or measurement nodes. Confirm stability with the intended load capacitance, avoid excessive resistive loading, and use the datasheet's input common-mode and output-swing limits when operating near either rail.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा OPA241UA — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | OPA241UAG4 | AD8676 | LT6015 | MAX44246 |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Analog Devices | Analog Devices | Maxim Integrated |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
मुख्य विशेषताएँ
- Very low supply demand for a general-purpose operational amplifier (बनामOPA241UAG4)
- Single 5 V supply operation with rail-to-rail output (बनामAD8676)
- Focused low-frequency signal-conditioning bandwidth (बनामMAX44246)
डिज़ाइन नोट्स
Budget the OPA241UA's 25 µA quiescent current together with output-current demand and the power consumed by surrounding circuitry. A nominally low-current amplifier can still raise total system consumption after accounting for sensor biasing, bypass leakage, conversion electronics, and protection components. Where the system operates intermittently, evaluate whether the shutdown behavior of the upstream circuit can provide a larger saving than selecting a marginally lower-current amplifier.
Place the supply bypass capacitor immediately beside the OPA241UA power pins and route the return directly to the device ground. Keep sensitive input traces short, away from switching-node and high-current return paths. Because the gain-bandwidth product is 35 kHz, the circuit is intended for slow signals, but correct grounding and local decoupling still determine whether offset, interference, and supply ripple appear as gain or common-mode errors.
Do not assume that rail-to-rail output swing permits operation at or beyond either supply rail. Check the input common-mode range, output swing under the intended load, gain setting, and minimum supply voltage from the manufacturer datasheet. Likewise, verify capacitive-load stability before connecting long cables, large filter capacitors, or ADC sampling inputs directly to the output.
अनुपालन जानकारी
The Texas Instruments product and ordering pages identify OPA241UA as active in an 8-pin SOIC package with a -40 °C to +85 °C operating range. Specific environmental and material compliance declarations were not present in the cited excerpts and require confirmation from the manufacturer.